ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Table of Contents Contents INTRODUCTION .................................................................................................. 3 Woodstock Technical Support ............................................................................ 3 Machine Specifications ....................................................................................4 Controls and Features .....................................................................................7 SAFETY ........
ページ4に含まれる内容の要旨
Setting RPM ............................................................................................... 30 RPM Chart ................................................................................................. 31 Setting Power Feed Rate ................................................................................ 32 Threading Setup .......................................................................................... 33 MAINTENANCE ................................................
ページ5に含まれる内容の要旨
INTRODUCTION Woodstock Technical Support ® Your new Model M1049 Benchtop Lathe has been specially designed to provide many years of trouble-free service. Close attention to detail, ruggedly built parts and a rigid quality control program assure safe and reliable operation. Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to include the basic information for safety, setup, operation, maintenance, and service of this pr
ページ6に含まれる内容の要旨
"#
$%
' * + ' / /
ページ7に含まれる内容の要旨
N%"X ^% ` ? ^% >~ { N%"X $
{> ? $
`~=@$ N%"X
ページ8に含まれる内容の要旨
# ]% $
% ' ] %# $ Z }%
|# ] X_ %{>
"`=@ $
[ !
; *#%
|** * >;+
; *#%
|*?\ X * _ #; *? z{[ # z{^\# z[ # ? Z_
-6-
ページ9に含まれる内容の要旨
Controls and Features B C A D E G F H I J S R Q P O M N L K Model M1049 Benchtop lathe. A. Belt and Change Gear Access Door K. Chip Tray B. Belt Tension Lever L. Thread Dial C. ON/OFF and Spindle Direction Switch M. Half Nut Lever D. 3-Jaw Chuck N. Apron Feed Lever E. Steady Rest O. Cross Slide Handwheel F. Back Splash P. Apron Handwheel G. Follow Rest Q. Headstock H. 4-Way Tool Holder R. Gearbox I. Compound Rest S. Gear Shift Lever J. Tailstock -7-
ページ10に含まれる内容の要旨
SAFETY For Your Own Safety, Read Manual Before Operating Machine Standard Machinery Safety Instructions Read and understand this Always wear hearing owner’s manual BEFORE using machine. protection when operating or observing Untrained users can be serious
ページ11に含まれる内容の要旨
Untrained operators Unexpected movement during can be seriously hurt by machinery. Only operations greatly increases the risk of injury allow trained or properly supervised people and loss of control. Verify machines are to use machine. When machine is not being stable/secure and mobile bases (if used) are used, disconnect power, remove switch keys, locked before starting. or lock-out machine to prevent unauthorized use—especially around children. Make Do not
ページ12に含まれる内容の要旨
Additional Safety Instructions for Lathes 1. AVOIDING INJURY: Read and understand this manual before operating this lathe. 2. AVOIDING LACERATIONS AND ENTANGLEMENT: Do not clear chips by hand. Use a brush, and never clear chips while the lathe is turning. 3. USING CORRECT TOOLING: Always select the right cutter for the job, and make sure cutters are sharp. The right tool decreases strain on
ページ13に含まれる内容の要旨
Avoiding Potential Injuries 3. Always wear face and eye protection 1. Always cover the bed ways, and when using this benchtop lathe. unplug the benchtop lathe when retooling. 4 Never use hands to stop or slow the 2. Never leave the chuck key inserted in chuck when shutting down the benchtop lathe. the chuck. 5. Never wear loose clothing or gloves when working with the benchtop lathe. -11-
ページ14に含まれる内容の要旨
ELECTRICAL Circuit Requirements This machine must be connected to the correct size and type of power supply circuit, or fire or electrical damage may occur. Read through this section to determine if an adequate power supply circuit is available. If a correct circuit is not available, a qualified electrician MUST install one before you can connect the machine to power. A power supply circuit includes all electrical equipment between the b
ページ15に含まれる内容の要旨
Grounding Requirements GROUNDED 110V 5-15 RECEPTACLE This machine MUST be grounded. In the event of certain types of malfunctions or breakdowns, grounding provides Grounding Prong a path of least resistance for electric current to travel—in order to reduce the risk of electric shock. Improper connection of the equipment-grounding wire will increase the risk of electric shock. The wire with green 5-15 PLUG insulation (with/without yellow stripes) is the equipment- Neu
ページ16に含まれる内容の要旨
SETUP Inventory The following is an inventory of the accessories shipped ® A C D with your Model M1049 Benchtop lathe. Installed Accessories (Figure 7) Qty A. 4" Three-Jaw Chuck .......................................1 B. 4-Way Tool Post ............................................1 C. Compound Rest ............................................1 D. Follow Rest .................................................1 B Packaged Accessories (Figure 8) E. Toolbox ..........
ページ17に含まれる内容の要旨
Machine Placement Cleaning Machine This machine distributes a The table and other unpainted parts of your heavy load in a small footprint. Some lathe are coated with a waxy grease that residential floors may require additional protects them from corrosion during shipment. bracing to support both machine and Clean this grease off with a solvent cleaner or operator. citrus-based degreaser. DO NOT use chlorine- based solvents such as brake parts cleaner or
ページ18に含まれる内容の要旨
Uncrating & Lifting This benchtop lathe has been carefully crated. If you notice it has been damaged, contact your authorized dealer immediately. 1. Remove the crate sides. 2. Unbolt the benchtop lathe from the pallet. 3. Place the chip tray onto the workbench surface and align the holes. 4. With lifting assistance place the lathe on the chip tray and align the mo
ページ19に含まれる内容の要旨
Test Run and Break-In The purpose of the test run is to make sure the benchtop lathe and safety features operate correctly before proceeding with additional setup. To begin the test run procedure, do these steps: Make sure the benchtop lathe is lubricated. Refer to if required. Make sure the chuck is threaded onto the spindle tightly and the two set screws are tight. Refer to on for details. Half-Nut Before starting th
ページ20に含まれる内容の要旨
LATHE OPERATIONS General The Model M1049 will perform many types of operations that are beyond the scope of this manual. Many of these operations can be dangerous or deadly if performed incorrectly. The instructions in this section are written with the understanding that the operator has the necessary knowl- edge and skills to operate this machine. If at any time you are experiencing difficulties performing any opera- tion, stop using the machine! I
