ページ1に含まれる内容の要旨
Model No. WESY38320
Serial No.
USER'S MANUAL
Write the serial number in the
space above for future reference.
Serial Number Decal (Under Seat)
QUESTIONS?
As a manufacturer, we are
committed to providing complete
customer satisfaction. If you
have questions, or if parts are
missing, we will guarantee com-
plete satisfaction through assis-
tance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The technicians on our cus-
tomer hot line will provide imme-
ページ2に含まれる内容の要旨
TABLE OF CONTENTS IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 ADJUS
ページ3に含まれる内容の要旨
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precautions before using the weight system. 1. Read all instructions in this manual and in 13. Always disconnect the lat bar from the the accompanying literature before using the weight system when performing an exercise weight system. that does not use the lat bar. 2. It is the responsibility of the owner to ensure 14. Make sure that the cables remain on the pul- that all users of the weight system
ページ4に含まれる内容の要旨
BEFORE YOU BEGIN ® Thank you for selecting the versatile WEIDER PRO Department toll-free at 1-800-999-3756, Monday ® 3550 weight system. The WEIDER PRO 3550 weight through Friday, 6 a.m. until 6 p.m. Mountain Time system offers an impressive array of weight stations (excluding holidays). To help us assist you, please designed to develop every major muscle group of the note the product model number and serial number body. Whether your goal is to tone your body, build before calling. The model num
ページ5に含まれる内容の要旨
ASSEMBLY Make sure that you have the following tools: Make Assembly Easier • Two adjustable wrenches Everything in this manual is designed to ensure that the weight system can be assem- • One standard screwdriver bled successfully by anyone. • One phillips screwdriver Before beginning assembly, make sure to • One rubber mallet read the information on this page. This brief introduction will save you much more • You will also need grease or petroleum jelly, a time than it takes to read it. s
ページ6に含まれる内容の要旨
1 FRAME ASSEMBLY 1. Make sure that you understand all of the 71 85 information on page 5 before you begin assembling the weight system. 120 86 Locate and open the parts bags labeled “FRAME 2 ASSEMBLY 1” and “FRAME ASSEMBLY 2.” 86 Press a 2” Square Inner Cap (105) into the open end of the Long Base (120). 105 Attach the Short Base (2) to the Long Base (120) with two 5/16” x 2 3/4” Bolts (85), the Long Frame 2 110 Plate (71), and two 5/16” Nylon Locknuts (86). Do 53 not tighten the Nylon Locknuts
ページ7に含まれる内容の要旨
4. Press a 1 1/2” Square Inner Cap (67) into the 4 square tube on the Butterfly Upright (3). Slide the Butterfly Upright onto the two indicated 5/16” x 2 1/2” Carriage Bolts (110) in the Short Base (2). Finger tighten a 5/16” Nylon Locknut (86) onto each Carriage Bolt. Do not tighten the Nylon Locknuts 67 yet. 3 86 86 2 110 5. Press a 2” x 3” Inner Cap (58) into the top of the 5 Seat Upright (9). Attach the Leg Lever Bumper (77) 58 to the Seat Upright with a #10 x 1” Screw (14). 9 Slide the Seat
ページ8に含まれる内容の要旨
7. Press a 2” x 3” Inner Cap (58) into the top of the 7 Squat Upright (4). Slide the Squat Upright onto the 58 two indicated 5/16” x 2 1/2” Carriage Bolts (110) in the Long Base (120). Finger tighten a 5/16” Nylon Locknut (86) onto each Carriage Bolt. Do not tight- en the Nylon Locknuts yet. 58 5 Press a 2” x 3” Inner Cap (58) into the top of the VKR Upright (5). Slide the VKR Upright onto the two indicated 5/16” x 2 1/2” Carriage Bolts (110) in the Long Base (120). Finger tighten a 5/16” Nylon
ページ9に含まれる内容の要旨
9. Insert the ends of two Weight Guides (42) into the 9 indicated bracket on the Long Base (120). Attach the Weight Guides to the Long Base with a 3/8” x 6 1/2” Bolt (95) and a 3/8” Nylon Locknut (87). 42 Attach the other two Weight Guides (42) to the Long Base (120) in the same way. 42 87 120 95 10. Slide two Weight Bumpers (49) onto the two indi- 10 cated Weight Guides (42). Next, slide ten Weights 42 (44) onto the Weight Guides. Make sure that the Weights are turned so the grooved sides of th
ページ10に含まれる内容の要旨
12. Press a 2” x 3” Inner Cap (58) into the Butterfly Top 12 92 Frame (7). Attach the Butterfly Top Frame to the Top Frame (6) with two 5/16” x 2 3/4” Bolts (85), two 90 5/16” Washers (90), and two 5/16” Nylon Locknuts (86). Do not tighten the Nylon Locknuts yet. 86 7 Attach the Butterfly Top Frame (7) to the Butterfly 6 90 Upright (3) with two 5/16” x 3 3/4” Bolts (92), two 5/16” 85 Washers (90), and two 5/16” Nylon Locknuts (86). 90 58 Tighten all of the 5/16” Nylon Locknuts (86) and 3 3/8” Ny
ページ11に含まれる内容の要旨
16. Lubricate a 3/8” x 3” Button Head Bolt (104) and 16 104 both sides of two Plastic Washers (56) with grease. Attach the Right Butterfly Arm (26) to the Butterfly 91 26 Frame (47) with the Bolt, the two Plastic Washers, 57 two Butterfly Caps (57), two 3/8” Washers (91), and 47 a 3/8” Nylon Jamnut (113) as shown. Make sure 56 that the recessed sides of the Plastic Washers are fitted over the welded bushing in the 57 25 Butterfly Arm. Do not overtighten the Nylon 91 Jamnut; the Butterfly Arm mus
ページ12に含まれる内容の要旨
20. Remove the preattached 3 1/2” Pulleys (78 [only 20 one is shown]) from the Offset Double “U”- bracket (61). Wrap the VKR High Cable (74) under a 3 1/2” Pulley (78). Attach the Pulley to the Offset Double “U”-bracket (61) with a 3/8” x 1 3/4” Bolt (93) and a 74 3/8” Nylon Locknut (87). 78 93 87 61 21. Wrap the VKR High Cable (74) over a 4 1/2” Pulley 21 (119). Attach the Pulley inside of the indicated 6 bracket on the Top Frame (6) with 3/8” x 1 3/4” Bolt 87 (93) and a 3/8” Nylon Locknut (87)
ページ13に含まれる内容の要旨
24. Route the Lat Cable (88) over a 3 1/2” Pulley (78). 24 Slide a Long Cable Trap (102) onto a 3/8” x 1 3/4” 88 78 6 Bolt (93). Attach the Pulley to the indicated bracket 87 on the Top Frame (6) with the Bolt and a 3/8” Nylon Locknut (87). Make sure that the Long Cable 102 Trap is turned to hold the Cable in the groove of the Pulley. 93 25. Remove the preassembled 3/8” Nylon Locknut (87) 25 and 3/8” x 2” Bolt (100) from the Pulley Plates (63). Wrap the Lat Cable (88) under a 3 1/2” Pulley (78).
ページ14に含まれる内容の要旨
28. Wrap the Butterfly Cable (69) over a “V”-pulley (55). 28 Attach the Pulley and a Long Cable Trap (102) to the indicated bracket on the Butterfly Upright (3) with a 3/8” x 2 1/2” Bolt (18) and a 3/8” Nylon Locknut (87). Make sure that the Long Cable Trap is turned to hold the Cable in the groove of the Pulley. 3 87 102 55 18 69 29. Remove the preattached 3 1/2” Pulleys (78) from 29 the Double “U”-bracket (62). Wrap the Butterfly Cable (69) under a 3 1/2” Pulley (78). Attach the Pulley to the
ページ15に含まれる内容の要旨
32. Locate the Leg Lever Cable (75), which is 88” 32 long and has an eyelet on one end and a thread- ed pin on the other end. Route the eyelet end of the Cable through the Seat Upright (9) and attach it 10 to the tab on the Leg Lever (10) with a 5/16” x 1” 86 Shoulder Bolt (103) and a 5/16” Nylon Locknut (86). 75 9 103 Tab 33. Attach a 3 1/2” Pulley (78) inside of the Seat 33 Upright (9) with a 3/8” x 2 3/4” Bolt (101), two 3/8” Washers (91), two 1/2” Spacers (89), and a 3/8” 9 Nylon Locknut (87
ページ16に含まれる内容の要旨
36. Remove the preattached 3 1/2” Pulley (not 36 shown) from the “U”-bracket (64). Attach the end of the Leg Lever Cable (75) to the 75 “U”-bracket (64) with a 1/4” Washer (97) and a 1/4” Nylon Locknut (34). Note: Do not completely tighten the Nylon Locknut; it should be thread- ed only two turns onto the end of the Cable. 64 97 34 37. Locate the VKR Low Cable (72), which is the 37 only remaining cable that has an eyelet on one 78 end and a ball on the other end. Route the eyelet 5 end of the Ca
ページ17に含まれる内容の要旨
40. Wrap the VKR Low Cable (72) under a 3 1/2” 40 Pulley (78). Attach the Pulley to the indicated brack- et on the Long Base (120) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Locknut (87). 78 72 87 93 120 41. Route the VKR Low Cable (72) under the indicated 41 stack of Weights (44). Wrap the VKR Low Cable (72) under a 3 1/2” 44 Pulley (78). Attach the Pulley to the indicated brack- et on the Long Base (120) with a 3/8” x 1 3/4” Bolt 78 72 (93) and a 3/8” Nylon Locknut (87). 87 93 120 42. Wra
ページ18に含まれる内容の要旨
44. Wrap the VKR Low Cable (72) over a 3 1/2” Pulley 44 (78). Attach the Pulley and a Cable Trap (68) between the lower set of holes in the “U”-bracket (64) with a 3/8” x 2” Bolt (100) and a 3/8” Nylon Locknut (87). Make sure that the Cable Trap is 100 turned to hold the Cable in the groove of the 64 Pulley. 68 87 72 78 45. Attach the end of the VKR Low Cable (72) inside of 45 the Short Base (2) with a 5/16” x 2 1/2” Bolt (59), two 5/16” Washers (90), and a 5/16” Nylon Locknut (86). 72 86 90 90
ページ19に含まれる内容の要旨
48. Wrap the Squat Cable (73) under a 3 1/2” Pulley 48 (78). Attach the Pulley to the indicated bracket on the Long Base (120) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Locknut (87). 78 73 87 93 120 49. Wrap the Squat Cable (73) over a 4 1/2” Pulley 49 (119). Attach the Pulley to the indicated bracket on 6 87 the Top Frame (6) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Locknut (87). 93 119 73 50. Place a 1/2” Washer (1) on top of the Weight Tube 50 (43) closest to the Squat Upright (4
ページ20に含まれる内容の要旨
52. Press two 3/4” x 1 1/2” Inner Caps (116) and a 1 1/4” 52 Square Inner Cap (117) into the Seat Bracket (11). 16 Attach the Seat (16) to the Seat Bracket (11) with two 1/4” x 3/4” Screws (114), a 1/4” x 1 1/2” Screw (99), and a 1/4” Washer (97). 116 97 Turn the indicated Adjustment Handle (65) counter- 11 clockwise several turns to loosen it. Next, pull the 99 Handle and insert the Seat Bracket (11) into the 116 Seat Frame (8). Engage the Handle into one of the 114 117 holes in the Seat Brack
