ページ1に含まれる内容の要旨
PATENT PENDING
Model No. 831.150470
USER'S MANUAL
Serial No.
The serial number can be found in the
location shown below. Write the serial
number in the space above.
Serial Number Decal (under seat)
CAUTION
Read all precautions and instruc-
tions in this manual before
using this equipment. Save this
manual for future reference.
SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179
ページ2に含まれる内容の要旨
TABLE OF CONTENTS LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 PART IDENTIFICATION CHART . . .
ページ3に含まれる内容の要旨
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precautions before using the weight bench. 1. Read all instructions in this manual before 10. Always be sure there is an equal amount of using the weight bench. weight on each side of your barbell (not included) when you are using it. 2. Use the weight bench only as described in this manual. 11. The weight bench is designed to support a maximum of 560 pounds, including the user, 3. It is the respons
ページ4に含まれる内容の要旨
WARNING DECAL PLACEMENT The decal shown below has been placed on the weight bench and on the squat rack. If either decal is missing, or if either decal is not legible, please call our Customer Service Department toll-free at 1-800- 999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays), to order a replacement decal. Apply the replacement decal to the location shown. 4
ページ5に含まれる内容の要旨
BEFORE YOU BEGIN ® Thank you for selecting the versatile WEIDER PRO Monday through Friday, 6 a.m. until 6 p.m. Mountain 545 Weight Bench. The PRO 545 Weight Bench is Time (excluding holidays). To help us assist you, designed to let you develop every major muscle group please note the product model number and serial of the body. Whether your goal is a shapely figure, dra- number before calling. The model number is matic muscle size and strength, or a healthier cardio- WEBE54570. The serial number
ページ6に含まれる内容の要旨
ASSEMBLY Before beginning assembly, carefully read the THE FOLLOWING TOOLS (NOT INCLUDED) ARE following information and instructions: REQUIRED FOR ASSEMBLY: • Assembly requires two people. • Two (2) adjustable wrenches • Place all parts in a cleared area and remove the • One (1) rubber mallet packing materials; do not dispose of the packing materials until assembly is completed. • One (1) standard screwdriver • Tighten all parts as you assemble them, unless • One (1) phillips screwdriver instruc
ページ7に含まれる内容の要旨
3. Press 20mm x 40mm Inner Caps (44) into the ends 3 44 of both Backrest Tubes (25). Lubricate an M10 x 152mm Bolt (11). Attach the Backrest Tubes (25) to the Bench Frame (49) with the Bolt, two M10 Washers (15), and an M10 Nylon 15 Locknut (14). The Backrest Brackets must be ori- 25 ented as shown. Do not overtighten the Nylon 15 14 Locknut; the Backrest Brackets must be able to 11—Lubricate move freely. 44 49 4. Slide the Adjustment Bracket (26) onto the Bench 4 Lubricate—11 Guide Frame (49).
ページ8に含まれる内容の要旨
7. Press three 50mm Square Inner Caps (36) into the 7 Leg Lever (32). Press a 1” Round Inner Cap (41) 36 into the Leg Lever. Press a 1” Angle Cap (5) onto the Leg Lever. 32 5 41 36 8. Lubricate the M10 x 72mm Bolt (10). Attach the Leg 8 Lever (32) to the Front Leg (22) with the Bolt and 14 an M10 Nylon Locknut (14). 32 10—Lubricate 22 9. Tap 3/4” Round Inner Caps (43) into each end of 9 48 the three Pad Tubes (38). 43 Insert a Pad Tube (38) through one hole in the Leg 38 22 Lever (32). Insert an
ページ9に含まれる内容の要旨
11. Note: The WEIDER PRO 545 is designed to be 11 used with both olympic and standard barbells. If you will be using an olympic barbell, assemble the base 31 in the wide position, as shown in the main drawing. 12 20 If you will be using a standard barbell, assemble the 12 base in the narrow position, as shown in the inset drawing. 20 Attach each section of the Base (20, 55) to an 8 31 Adjustment “U” Bracket (31) with two M8 x 68mm 55 8 Bolts (8) and two M8 Nylon Locknuts (12). Do not tighten the
ページ10に含まれる内容の要旨
14. Insert a Weight Rest (37) into each Rear Upright 14 (19). Be sure that the Weight Rests are inserted at the same level on both sides. 19 37 19 37 15. Slide a Front Upright (18) onto the indicated M8 x 15 58mm Carriage Bolts (6) in either section of the A second person Base (20, 55). A second person must hold the must hold each Upright at the location shown during the step. Upright here while Partially tighten an M8 Nylon Locknut (12) onto the Nylon Locknuts each Carriage Bolt but do not full
ページ11に含まれる内容の要旨
17. Slide a Carriage Stop (54) onto a Front Upright 17 (18). Be sure that the 60mm Square Bushing (53) is facing up. Align the holes in the Carriage Stop with the holes in the Front Upright. Insert 52 an M8 x 68mm Bolt (8) through the Carriage Stop and Front Upright. Tighten an M8 Nylon Locknut (12) onto the Bolt. Slide a Weight Carriage (52) onto the Front Upright (18). The weight tube must be on the side shown. 18 Attach the other Carriage Stop (54) and Weight Carriage (52) in the same manner.
ページ12に含まれる内容の要旨
19. Attach each section of the Top Frame (21, 39) to 19 8 the Front Uprights (18) with an M8 x 68mm Bolt (8), 13 two M8 Washers (13), and an M8 Nylon Locknut 21 (12). Attach each section of the Top Frame (21, 39) to 39 8 the Rear Uprights (19) with two M8 x 68mm Bolts 12 13 (8), two M8 Washers (13), and two M8 Nylon Locknuts (12). 8 12 13 Tighten all Nylon Locknuts and Bolts used in 19 19 steps 11–19. 12 18 18 8 12 13 20. Attach a Cable (51) to one of the Weight Carriages 20 (52) with an M10 x 7
ページ13に含まれる内容の要旨
23. Press a 1” Round Inner Cap (41) into each end of a 23 Spotter Tube (4). 4 Press a 1” Round Inner Cap into each end of the 41 other Spotter Tube (not shown). 41 24. Insert a Spotter Tube (4) through a Front Upright 24 (18) and into a Rear Upright (19). Rotate the Spotter Tube so that the hook locks in place around the Front Upright. 18 Insert the other Spotter Tube through the other Front and Rear Upright (not shown) in the same manner. Be sure that the Spotter Tubes are 19 inserted at the sa
ページ14に含まれる内容の要旨
ADJUSTING THE WEIDER PRO 545 The weight bench is designed to be used with your own weight set (not included). The steps below explain how the weight bench can be adjusted. See EXERCISE GUIDELINES on page 17 for important exercise information and refer to the accompanying exercise poster to see the correct form for each exercise. Refer also to the exer- cise information accompanying your weight set (not included) for additional exercises. Inspect and tighten all parts each time you use the weight
ページ15に含まれる内容の要旨
ADJUSTING THE WEIGHT RESTS Squat exercises and toe raise exercises naturally require that the Weight Rests (37) be set to a different height than bench press exercises. You should always set the Weight Rests to a height which is comfortable for the exercise you will perform. To adjust the Weight Rests (37), insert the Weight Rests into the adjustment holes in the Rear Uprights (19) at the desired height. Be sure that each Weight Rest is firmly seated in the adjustment hole and that both 37 Weigh
ページ16に含まれる内容の要旨
ADJUSTING THE WIDTH OF THE SQUAT RACK 21 8 If you buy a new barbell, you may need to change the 1 width of the squat rack. If you are using an olympic barbell, you must use the wide setting. If you are using a five or six foot long barbell, you must use 31 39 the narrow setting. To move the squat rack from the narrow setting to 12 the wide setting: Remove the Adjustment “U” Bracket (31), four M8 x 68mm Bolts (8), and four M8 Nylon Locknuts (12) from each section of the Base (20, 55). Remove the
ページ17に含まれる内容の要旨
EXERCISE GUIDELINES THE FOUR BASIC TYPES OF WORKOUTS PERSONALIZING YOUR EXERCISE PROGRAM • Muscle Building We have not specified an exact length of time for each workout, or a specific number of repetitions or In order to increase the size and strength of your sets for each exercise. It is very important to avoid muscles, you must push your muscles to a high per- overdoing it during the first few months of your exer- centage of their capacity. You must also progressively cise program, and to pro
ページ18に含まれる内容の要旨
for 3 minutes after each set if you are doing a muscle STAYING MOTIVATED building workout, 1 minute after each set if you are doing a toning workout, and 30 seconds after each For motivation, keep a record of each workout. The set if you are doing a weight loss workout. Plan to chart on page 19 of this manual can be photocopied spend the first couple of weeks familiarizing yourself and used to schedule and record your workouts. List with the equipment and learning the proper form for the date, e
ページ19に含まれる内容の要旨
EXERCISE WEIGHT SETS REPS MONDAY Date: / / AEROBIC EXERCISE TUESDAY Date: / / EXERCISE WEIGHT SETS REPS WEDNESDAY Date: / / AEROBIC EXERCISE THURSDAY Date: / / EXERCISE WEIGHT SETS REPS FRIDAY Date: / / Make photocopies of this page for scheduling and recording your workouts. 19
ページ20に含まれる内容の要旨
M8 Nylon Locknut (12)—30 M10 Nylon Locknut (14)—9 M6 Washer (42)—7 M8 Washer (13)—12 M10 Washer (15)—2 M6 x 60mm Screw (16)—1 M6 x 48mm Screw (35)—4 M10 x 90mm Bolt (7)—2 M6 x 16mm Screw (17)—2 M8 x 68mm Bolt (8)—22 M8 x 58mm CarriageBolt (6)—8 M10 x 48mm Bolt (9)—2 M10 x 72mm Bolt (10)—3 M10 x 152mm Bolt (11)—2
