ページ1に含まれる内容の要旨
Assembly
Guide
R2600iNetTV
COMMERCIAL FITNESS BIKE
ページ2に含まれる内容の要旨
Assembly Guide R2600iNetTV COMMERCIAL FITNESS BIKE To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order. Before proceeding, find your new Fitness Bike’s serial number located on the front axle tube, and enter here: Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be sure to read your Owner’s Guide before using your new Fitness Bike. If any parts, hardware or tools are missi
ページ3に含まれる内容の要旨
TOOLS & PARTS INCLUDED MM MM 5 Allen Wrench 6 Allen Wrench MM 4 L-Shaped Wrench Screwdriver MM 5 L-Shaped Wrench PARTS BOX Console Mast Cover, Qty: 1 Water Bottle & Cage, Qty: 1 CONSOLE BOX Heart Rate Chest Strap, Qty: 1 Color-coded Hardware Bags iNetTV Console Assembly Guide Owner’s Guide Warranty Card
ページ4に含まれる内容の要旨
HARDWARE INCLUDED ORANGE BAG GREEN BAG M8x65L Screw Quantity: 2 M8 Lock Washer M8 x 15L Screw Quantity: 8 Quantity: 4 M8 Lock Washer M8 x 20L Screw Quantity: 4 Quantity: 2 M8 x 20L Screw Quantity: 4 BLUE BAG BLACK BAG M8 Lock Washer M8 x 15L Screw Quantity: 6 Quantity: 7 M6 x 55L Screw Quantity: 8 PINK BAG M6 Lock Washer Quantity: 8 M8 Lock Washer M8 x 20L Screw Quantity: 4 Quantity: 2
ページ5に含まれる内容の要旨
STEP 1 ORANGE BAG • Install the rear foot with the four lock STEP 1 washers (M8), two inside screws (M8x65L), and two outside screws MM (M8x20L). Tighten with the 5 Allen wrench. STEP 2 BLUE BAG • Slide the rubber boot onto the console mast. • Locate the bundle of wires that comes from the console mast frame bracket. Wrap the wire tie coming from the bottom of the console mast around the bundle of wires. Pull the wire tie with the bundle of wires up through the top of the console mast while sim
ページ6に含まれる内容の要旨
STEP 3 PINK BAG STEP 3 • Mount the upper handlebars to the console mast using two lock washers (M8) and two screws (M8x20L). MM Tighten with the 5 Allen wrench. STEP 4 CONSOLE • Remove the six mounting screws from the back of the console. Set the console into place on the console mast and secure it with the six screws you just removed. Tighten with the Phillips screwdriver. Connect the wires STEP 4 to the proper plugs in the back of the console (see diagram). 1 - Co-Axial Cable TV 2 - USB - B 3
ページ7に含まれる内容の要旨
STEP 5 GREEN BAG • Attach the seat frame to the sliding seat bracket using four socket head MM cap screws (M8x20L) and the 6 Allen wrench. • Connect Wires A on the seat handlebar to Wires B on the sliding Wires A seat bracket. Attach the seat handlebars to the sliding seat bracket using four lock washers (M8) and four MM screws (M8x15L). Tighten with the 5 Allen wrench. STEP 5 Wires B 7
ページ8に含まれる内容の要旨
STEP 6 BLACK BAG • Secure the Lumbar controlled seat back and the seat bottom to the seat frame with eight lock washers (M6) and eight screws (M6x55L). Tighten MM with the 4 Allen wrench. • Snap the plastic seat cover into place on the back of the Lumbar controlled seat. STEP 6 500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551 toll free 1.800.335.4348 • phone 1.920.648.4090 • fax 1.920.648.3373 www.visionfitness.com 2002 Vision Fitness. All Rights Reserved. 8.02 Part #Z26RB60
