ページ1に含まれる内容の要旨
™
Open All
Electric Can Opener
Instruction Booklet
CA2800
Please read these instructions carefully
and retain for future reference.
ページ2に含まれる内容の要旨
Contents Sunbeam’s Safety Precautions 1 Safety Precautions for your Open All 1 Features of your Open All 2 Using your Sunbeam Open All 4 Care and Cleaning of your Open All 6 Important instructions – retain for future use.
ページ3に含まれる内容の要旨
Sunbeam’s Safety Precautions SAFETY PRECAUTIONS FOR YOUR • Do not place any part of this appliance in SUNBEAM OPEN ALL. a dishwasher. • Keep fingers well away from blade when in use. • Use extreme care when handling off-cuts. • Use extreme care when handling blades. Sunbeam is very safety conscious when • Do not use an appliance for any purpose designing and manufacturing consumer products, other than its intended use. but it is essen
ページ4に含まれる内容の要旨
Features of your Open All Release Button Cutting Assembly Support Bar Drive Wheel Knife Sharpener Built in ceramic knife sharpener will ensure that your knives remain sharp at all times. Cord Storage Handy cord storage keeps the benchtop tidy by storing unwanted cord. 2
ページ5に含まれる内容の要旨
Lever Blade Magnetic Lid Holder Stainless steel blade cutting action Stainless steel blade allows for a smoother cutting action. Magnetic lid holder Holds the lid in place during and after the can is fully opened. Removable lever For easy cleaning, slide the release button and remove the cutting assembly/lever. Automatic operation Simply lift the lever and position the blade inside the rim of the can. Press the lever ™ down and the Open A
ページ6に含まれる内容の要旨
Using your Sunbeam Open All 1. E nsure that the Cutting Assembly is correctly positioned. (See figure 1.) Support Lever Bar Release Button Drive Wheel Keyhole Figure 2 Drive Wheel Figure 1 4. F irmly press the Lever down. This action will bring the blade down and pierce The Cutting Assembly fits into the the lid of the can and start operating keyhole opening at the top of the Open the motor to turn the can. Ensure the ™ All can
ページ7に含まれる内容の要旨
7. T o remove the can, support the can with one hand and lift the Lever with the other. The lid will remain attached to the Magnetic Lid Holder. (See figure 4.) Figure 4 CAUTION: Be careful when removing the lid from the magnet as the cut edge is sharp. Opening dented/damaged cans: Occasionally, badly dented cans will cause ™ the Open All can opener to stall. If this happens, grasp the dented can and guide it through the cutting
ページ8に含まれる内容の要旨
Care and Cleaning Turn the power off and unplug the cord from Drive Wheel: the power outlet before cleaning. The Cutting Wipe with a damp cloth to thoroughly clean, Assembly is easily removed for thorough use a small brush to remove accumulated cleaning. (See figure 5.) dirt. Release Button Motor Housing: Wipe over with a damp cloth. Keyhole Do not use harsh abrasives or cleaners to ™ clean any parts of your Open All can opener, a
ページ9に含まれる内容の要旨
Notes
ページ10に含まれる内容の要旨
Notes
ページ11に含まれる内容の要旨
12 Month Replacement Guarantee In the unlikely event that this appliance develops any malfunction within 12 months of purchase (3 months commercial use) due to faulty materials or manufacture, we will replace it for you free of charge. Should you experience any difficulties with In Australia you are entitled to a your appliance, please phone our customer replacement or refund for a major failure and service line for advice on 1300 881 861 in for compensati
ページ12に含まれる内容の要旨
Need help with your appliance? Contact our customer service team or visit our website for information and tips on getting the most from your appliance. In Australia Visit www.sunbeam.com.au Or call 1300 881 861 In New Zealand Visit www.sunbeam.co.nz Or call 0800 786 232 is a registered trademark. ‘Open All’ is a trademark of Sunbeam Corporation. Made in China. Due to minor changes in design or otherwise, the product may differ from the one shown in this leaflet. © Copy
