ページ1に含まれる内容の要旨
Page 1
MODEL 808331
IN-LINE BLOWER
For use with models CTWH30, CTWH36, IH4227,
W302418, W302718, W362210-482210
READ AND SAVE THESE INSTRUCTIONS
! !
FOR DOMESTIC COOKING ONLY
WARNING WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY 4. Use an extinguisher ONLY if:
TO PERSONS, OBSERVE THE FOLLOWING:
A. You know you have a Class ABC extinguisher and you already
1. Use this unit only in the manner intended by the manufacturer. If know how to operate it.
you have questions, contac
ページ2に含まれる内容の要旨
Page 2 TYPICAL INSTALLATION TYPICAL INSTALLATION MOUNTING (New Frame Construction) MOUNTING USING HANGER KIT (included) 10” ROUND DUCT 4½” X 18½” Mounting brackets TO 10” ROUND HANGER factory-shipped in TRANSITION KIT BOLT position for ½” ceil- & WASHER ing material. EXTENSION CEILING SPRING JOIST HANGER 10” ROUND (24” centers KIT CHAIN DUCT (INTAKE) shown) HANGER KIT EYE-BOLT 4½” X 18½” TO 10” ROUND HANGER TRANSI- 10” ROUND KIT NUT & Blower factory-shipped TION DUCT WASHER in horizonta
ページ3に含まれる内容の要旨
Page 3 WIRING WIRING PLATE POSITION BLACK TO TOP / BACK BLACK OF HOUSING VERTICAL GROUND TO POWER CABLE WIRING PLATE CONNECTION WIRING PLATE HORIZONTAL POWER CABLE CONNECTION 120 VAC LINE IN WHITE (from Wiring plate mounts to side or top of housing. TO range WHITE hood) Ventilator can be wired from outside of housing. Use UL approved connectors to wire per local codes. DUCTING OPTIONS MOUNTING OPTIONS BLOWER DISCHARGE POSITIONS ¼-20 hex nuts secure mounting brackets to housing. Loosen and DUC
ページ4に含まれる内容の要旨
Page 4 ATTACH POWER CORD TO USE AND CARE To clean blower assembly: Remove access panel, unplug blower HOOD from housing, remove blower mounting nuts, and carefully remove blower from housing. Use appropriate vacuum attachment or a soft Follow wiring instructions packed with range hood, and adhere to cloth and mild soap or detergent to clean blower discharge area and all local and state codes, and the National Electrical Code. wheel. DO NOT ALLOW WATER TO ENTER MOTOR. Make sure blower assem
ページ5に含まれる内容の要旨
Page 1 MODEL 808332 IN-LINE BLOWER For use with models CTWH30, CTWH36, IH4227, DD30R, DD36R, DD45R, W30-662418, W30-662718, L28-582212, I36-663418 READ AND SAVE THESE INSTRUCTIONS ! ! FOR DOMESTIC COOKING ONLY WARNING WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY 4. Use an extinguisher ONLY if: TO PERSONS, OBSERVE THE FOLLOWING: A. You know you have a Class ABC extinguisher and you already 1. Use this unit only in the manner intended by the manufacturer. If know how to op
ページ6に含まれる内容の要旨
Page 2 TYPICAL INSTALLATION TYPICAL INSTALLATION MOUNTING (New Frame Construction) MOUNTING USING HANGER KIT (included) 10” ROUND DUCT 8” X 12” TO 8” X 12” TO 8” X 12” TO (OUTLET) 10” ROUND 10” ROUND HANGER 10” ROUND TRANSITION KIT BOLT TRANSITION TRANSITION (FEMALE) & WASHER (FEMALE) (MALE) EXTENSION SPRING 10” ROUND DUCT HANGER 10” ROUND (INTAKE) KIT CHAIN DUCT (INTAKE) HANGER KIT EYE-BOLT GRILLE NUT (Install into square 8” X 12” TO holes in housing) 10” ROUND HANGER MOUNTING TRANSITI
ページ7に含まれる内容の要旨
Page 3 WIRING WIRING PLATE POSITION BLACK TO BLACK EDGE OF HOUSING GROUND TO VERTICAL WIRING PLATE POWER CABLE CONNECTION WIRING PLATE HORIZONTAL POWER CABLE CONNECTION WHITE TO Wiring plate mounts to side or top of housing. WHITE 120 VAC LINE IN (from range hood) DUCTING OPTIONS Ventilator can be wired from outside of housing. BLOWER DISCHARGE POSITIONS Use UL approved connectors to wire per local codes. DUCT DUCT Housing MOVABLE CONNECTOR rotated & mov- CONNECTOR PANEL (outlet) able panel
ページ8に含まれる内容の要旨
Page 4 ATTACH POWER CORD TO USE AND CARE To clean blower assembly: Remove access panel, unplug blower HOOD from housing, remove blower mounting nuts, and carefully remove blower from housing. Use appropriate vacuum attachment or a soft Follow wiring instructions packed with range hood, and adhere to cloth and mild soap or detergent to clean blower discharge area and all local and state codes, and the National Electrical Code. wheel. DO NOT ALLOW WATER TO ENTER MOTOR. Make sure blower assem
