ページ1に含まれる内容の要旨
®
My Café AP
PROGRAMMING MANUAL
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644
41170.0001A 05/12 ©2010 Bunn-O-Matic Corporation
ページ2に含まれる内容の要旨
BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers thermal servers and Thermofresh servers (mechanical and digital)- 1 year parts and 1 year labor. 2) All other equipment - 2 years parts and 1 year labor plus added warranties as specified below: a) Electronic circuit and/or control boards - parts and labor for 3 years. b) C
ページ3に含まれる内容の要旨
CONTENTS LOCKOUT SWITCH .............................................................................................4 PROGRAMMING SWITCHES...............................................................................5 PROGRAMMING .................................................................................................6 41170.1 050312 Page 3
ページ4に含まれる内容の要旨
ADJUSTMENTS & PROGRAMMING PROGRAMMING THE BREWER The programming of the brewer is divided into two levels. Brewing adjustments are in Level 1. Service func- tions are accessed in Level 2. The following function screens are in order of appearance. Each screen will have instructions on how to access, and the procedures to program the various functions of the brewer. IMPORTANT PROGRAMMING NOTES - READ CAREFULLY - To exit the programming mode at any time, press and hold "Hidden" switch located
ページ5に含まれる内容の要旨
PROGRAM FUNCTIONS MAIN SCREEN HIDDEN SWITCH Press until display reads "BREW LOCKOUT" Press/hold to exit program SMALL BREW Step backwards through screens BREW LOCKOUT: NEXT BREW LOCKOUT ? Prevents brewing if the water temperature is less than NO DONE YES the "SET READY" temperature. To access this function screen press and hold the hidden switch. Release when the display reads: "BREW LOCKOUT". The YES or NO should be flashing. Select YES to prevent brewing if the water temperature is
ページ6に含まれる内容の要旨
PROGRAM FUNCTIONS BREW LOCKOUT (YES/NO) BREW LOCKOUT ? Setting to "YES" only allows brewing at or above the "SET READY" temp screen. NO DONE YES BREW OZ. (LARGE) (1-16) BREW OZ A: 8.0 Adjust brew volume for "LARGE" button. (-) DONE (+) BREW METER (LARGE) (1-5) BREW METER A: 2 Simplified pulse brew adjustment. 1=Preinfusion. 2-5=pulse brew, - + 2 being the shortest pulse brew cycle, 5 the longest pulse brew cycle. BREW OZ
ページ7に含まれる内容の要旨
PROGRAM FUNCTIONS HOT H2o READY H2O READY: 190° Sets the minimum temperature allowable to start dispensing hot water. (-) DONE (+) ENTER ASSET # ENTER ASSET # ? This function allows the you to enter in an optional asset number. This can be NO YES useful for tracking the usage or service of an individual machine within a group. SET PULSE BREW (LARGE) SetPulseBrew A ? Individually adjust on/off times. NO DONE YES AIR TIME (LARGE
ページ8に含まれる内容の要旨
PROGRAM FUNCTIONS SERVICE TOOLS allows testing of load components and switches. SERVICE TOOLS ? It should only be used by trained technicians. NO YES TEST OUTPUTS allows testing of load components by manually turning them TEST OUTPUTS ? ON/OFF. ---PLACE A 10 OUNCE CUP UNDER DISPENSE AREA--- NO YES WARNING: HOT WATER WILL DISPENSE DURING SOME TEST MODES! INDEX MOTOR DUMP runs the pod holder back to the pod ejection position. INDEX B MO
ページ9に含まれる内容の要旨
PROGRAM FUNCTIONS SET REFILL SET REFILL Press "YES" to access the refill screen. FOR TRAINED TECHNICIANS ONLY. NO THRESHLD YES IMPROPER SETTINGS CAN RESULT IN OVER FLOW! REFILL Adjust sensitivity of refill probe according to water quality. Always # REFILL ### make sure that the # on the right is larger than the # on the left when (-) DONE (+) water is contacting the tank refill probe. FACTORY DEFAULTS FACTORY DEFAULTS Reset all brew settings
