ページ1に含まれる内容の要旨
USER'S MANUAL
Model No. 831.159412
Serial No.
Write the serial number in the
space above for reference.
Serial Number Decal
F- x EE R C i _%_E_
EQUIPMENT
HELPLINE!
1-800-735-5879
CAUTION!
Read all precautions and
Instructions in this user's man-
ual before using this equip-
ment. Save this user's manual
for future reference.
PATENT PENDING
SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179
ページ2に含まれる内容の要旨
TABLE OF CONTENTS IMPORTANT PRECAUTIONS ..................................................................... 2 BEFORE YOU BEGIN ........................................................................... 3 ASSEMBLY .................................................................................... 4 TROUBLE-SHOOTING AND MAINTENANCE ....................................................... 10 USING THE BODYLIFT ......................................................................... 11 ORDERING
ページ3に含まれる内容の要旨
BEFORE YOU BEGIN Thank you for selecting the PROFORtvP BODYLIFT Department toil-free at 1-800-736*6879, Monday Body Weight Resistance System. The compact through Saturday, 7 a.m. until 7 p.m. Central Time BODYLIFT features an impressive array of weight sta- (excluding holidays). To help us assist you, please tions designed to develop every major muscle group note the product model number and serial number of the body. Whether your goal is a shapely figure, before calling. The model number is 831
ページ4に含まれる内容の要旨
ASSEMBLY Before beginning assembly, carefully read the • As you assemble the BODYLIFT, make sure that following Information end Instructions: all parts are oriented exactly as shown in the drawings. • Assembly requires two people. • Tighten all parts as you assemble them, unless • Due to the size of the BODYLIFT, it should be instructed to do otherwise. assembled in the location where it will be used. THE FOLLOWING TOOLS (NOT INCLUDED) ARE • Place all parts of the BODYLIFT in a cleared area REQU
ページ5に含まれる内容の要旨
Attach the Footrest (35) to the Front Upright (7) 3. 3 with two 3/8" x 2 3/4" Bolts (85), two 3/8" Flat Washers (53), and two 3/8" Nylon Locknuts (33) as shown. 35 85 53 . Remove the 3/8" x I 112"Carriage Bolt (80) and 4 the 3/8" Nylon Jam Nut (41) from the indicated brackets on the Front Upright (7). Remove the 19 loop of Cable (25) from the brackets. 41 Lubricate the 3/8" x 1 1/2" Carriage Bolt (80). Attach the Selector Plate (19) to the brackets on the Front Upright (7) with the Carriage Bolt
ページ6に含まれる内容の要旨
. Slide a Weld Cover (63) onto each of the indicat- ed axles on the Front and Rear Uprights (7, 2). The Weld Covers must be tumed so the open sides are facing the Uprights. Lubricate the axles. 2 Slide a Short Riser (4) onto the axles, The Short Riser must be turned as shown. Lubricate Hold a 3/4" J=tetainer (57) and a 3/4" Retainer Cap (59) against the end of one of the axles. The teeth on the Retainer must bend toward the Retainer Cap (see the inset drawing). Tap the Retainer and Retainer Cap
ページ7に含まれる内容の要旨
Carefully cut the wire tie attached to the Cable (25). Wrap the loop of Cable from steps 4 and 5 around the 3 1/2" Pulley (27) as shown. Hold the Pulley and the Pulley Covers (88) between the indicated holes in the Selector Plate (19). Make sure that the Pulley Covers are turned so the small rims are inside the loop of Cable as shown. See assembly step 9, and make sure that the Cable is routed exactly as shown. Attach the Pulley Covers (88) and the 3 1/2" Pulley (27) to the Selector Plate (19) w
ページ8に含まれる内容の要旨
10.PulltheMoment Arm(10)forward. Hold the lower and of the Left Press Arm (52) in the upper end of the Moment Arm. The Left Press Arm must be turned so the Handle (12) is on the side shown. Attach the Left Press Arm with two 3/8" x 2 1/2" Bolts (44) and two 3/8" Nylon Locknuts (33). The lO 12 Bolts must be Inserted from the side shown, or the BOBYLIFT will not function properly. Press a Small Bumper (91) onto the underside of the Handle (12). Assemble the Right Press Arm (11) in the same manner.
ページ9に含まれる内容の要旨
14. InsertonePadTube(13)intotheSeatFrame(8). 14 InserttheotherPadTubeintotheLegLever(9). Slide two 6" Pads (24) onto each Pad Tube (13). 24 24 15. Pivot the Link Tube (16) on the Left Arm (5) onto 15 the end of the Link Tube Axle (17). Attach the Link Tube to the Link Tube Axle with a 114"x 1 1/4" Bolt (49) and a 1/4" Acorn Nut (62). Tap a 1" x 1" Inner Cap (36) into the Link Tube (16). Attach the Link Tube (16) on the Right Arm (6) to the Link Tube Axle (17) in the same manner. 16 62 16. Make s
ページ10に含まれる内容の要旨
TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the BODYLIFT. Replace any worn parts immediately. The BODYLIFT can be cleaned using a damp cloth and mild non-abrasive detergent, Do not use solvents, HOW TO TIGHTEN THE CABLE Woven cable, the type used on the BODYLIFT, can stretch slightly when it is first used. If there is slack in the Cable (25), the Cable should be tightened. First, move the selector to hole position Ul" (see HOW TO Ball SELECT A RESISTANCE SETT
ページ11に含まれる内容の要旨
USING THE BODYLIFT The instructions below describe how each part of the BODYLIFT can be adjusted. Refer to the EXERCISE GUIDE accompanying this user's manual for exercise guidelines, and to see how the BODYLIFT should be set up for each exercise. IMPORTANT: When attaching the lat bar or nylon strap, make sure that the attachments are in the correct starting position for the exercise to be performed. If there is any slack in the cable or chain as an exer- cise is performed, the effectiveness of t
ページ12に含まれる内容の要旨
ページ13に含まれる内容の要旨
Thischartisprovided tohelpyouidentify thesmallpartsusedinassembly. Remove thischartfromtheuser'smanual before beginning assembly.
ページ14に含まれる内容の要旨
PART IDENTIFICATION CHARTmModel No. 831.159412 This chart is provided to help you identify the small parts used in assembly. The number in parenthesis below each part refers to the key number of the part. The second number refers to the quantity needed for assembly. Note: Some parts may have been pre-assembled for shipping purposes; if you cannot find a part in the parts bag, check the frame to see if it has been pre-assembled. O 1/4" Acorn Nut (62)-2 1/2" x 1" Sleeve (89)-1 J Weld Cover (63)-8
ページ15に含まれる内容の要旨
1/4"x 3/4" Sorew (47)-2 1/4" x 1 1/4" Bolt (49)-3 5/16" x 2 3/4" Bolt (78)-1 3/8" x 2" Bolt (87)-1 1/4" x 2 1/2" Screw (32)-1 1/4" x 2 1/2" Carriage Bolt (46)-1 3/8" x 2 1/2" Carriage Bolt (70)-4 3/8" x 2 1/2" Bolt (44)-4 1/4" x 1 3/4" Bolt (43)-1 R0195B Printed in USA© 1995 Seam, Roebuck and Co. 3/8" x 2 3/4" Bolt (85)--3
ページ16に含まれる内容の要旨
EXPLODED DRAWING--Model No. 831.159412 4 \ 18 27 5O 41 53 75 57 71 59 79 19 14 4O 46 33 24 21 67 69 .78 13 59 63 57 12 33 9O 24 63 52 i 85 6O 72 37 .-'" 33 53 81 _. 27, 66 42 RO195B
ページ17に含まれる内容の要旨
PART LIST--Model No. 831.159412 Key Part Key Part No. No. Qty. Description No. No. Qty. Description 3/8" x 4 1/2" Bolt 1 120574 1 Base 54 013485 1 1/4" Nylon Jam Nut 2 120575 1 Rear Upright 55 121576 3 5/8" Retainer 3 121466 2 Long Riser 56 102603 2 3/4" Retainer 4 121467 2 Short Riser 57 101578 8 1 1/2" Round Bushing 5 121468 1 Left Buttedly Arm 58 120810 16 3/4" Retainer Cap 6 121469 1 Right Butterfly Arm 59 120788 8 Pivot Tube 7 120580 1 Front Upright 60 120793 1 1/2" x 1/4" Spacer 8 120581 1
ページ18に含まれる内容の要旨
HOW TO ORDER REPLACEMENT PARTS Each BODYLIFT has its own MODEL NUMBER. Always mention this MODEL NUMBER when requesting service or repair parts for your BODYLIFT. All parts listed herein can be ordered through SEARS, ROEBUCK AND CO. SERVICE CENTERS and most SEARS RETAIL STORES. If parts you need are not stocked locally, your order will be transmitted to a SEARS PARTS DISTRIBUTION CENTER for handling. WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION: • The MODEL NUMBER of the pro
