ページ1に含まれる内容の要旨
INFRARED WOODEN SAUNA ROOM INSTRUCTION MANUAL
Read all instructions carefully before using the wooden infrared sauna room
IG-520 BH
PRECAUTIONS FOR USE.......................................................1
PARTS NAMES...............................................................2
READ BEFORE INSTALLATION..................................................3
INSTALLATION OF SAUNA ROOM BODY ..............................................4-7
CONTROL PANEL INSTRUCTION .............
ページ2に含まれる内容の要旨
ATTENTION ※Read all instructions before using this appliance. ※Serious injury may result if warnings and instructions below are not observed. ※When using an electrical appliance, basic precautions should always be followed, including the following: DANGER To reduce the risk of burns, fire, electric shock, or injury to persons. ※Connect the power cord to a properly grounded outlet only. ※Use this appliance only for its intended use as described in this manual. Do not use attachmen
ページ3に含まれる内容の要旨
PARTS NAMES IG-520-BH-2 5/25/07
ページ4に含まれる内容の要旨
READ BEFORE INSTALLATION: ※ Each panel is heavy. Be careful to avoid injury when installing, especially the top panel. ※ Two adults are required for the installation of sauna room. ※ There is a “+” button or a “–” button at the sides of each panel, which will be installed correspondently with one “+” to one “–” in following way when installing: The panel with “+”button should be lifted up about 4 inches (10cm) higher than the panel with the “-“ button (Refer to Picture 1); place th
ページ5に含まれる内容の要旨
INSTALLATION OF SAUNA ROOM BODY 1. Place the floor panel in the desired location on a level surface (Note: The floor panel must be level before installing wall and ceiling panels. If the surface is not level you may need to shim the bottom panel to get level.) ※ Make sure lines/grooves of the flooring of the floor panel are parallel with the front wall. 2. Place back panel in the slot of floor panel. 3. Place the left side panel in the slot of floor panel. 4. Place the right sid
ページ6に含まれる内容の要旨
5. Place the Bench Support panel first and then place the Bench surface panel into the sauna room. ※ On larger sauna rooms with more than one bench, rotate the wooden bench supports away from the side walls. ※ Slide the Bench Support Panel down the wooden supports with the heater facing out. ※ Make sure the two side slots of the Bench Support Panel slide completely into the corresponding grooves of the wooden supports . (Refer to picture 1) ※ Connect the power connector from the back o
ページ7に含まれる内容の要旨
6. Place the front panel in the slot of floor panel. 7. Place the top panel on the four side panels. Make sure the connection wires from the three side panels protrude through the corresponding holes of the top panel. ※ Make sure the top panel’s arched side is facing to the front. ※ Make sure the wire is through each hole smoothly and completely. ※ Make sure trim of the top panel fits completely around the four side panels. 8. Make sure each of the lead wires on the
ページ8に含まれる内容の要旨
WARNING: ELECTRIC SHOCK HAZARD Do not plug cord into electrical outlet before connecting power cord wires to terminal block. 9. Make sure to connect wires in correct location by matching color to correct screw location: ※ Open cover on top side of ceiling panel to see three unconnected power wires (Picture 1) ※ Insert the green wire into “〒” and tighten the screw (Picture 2) ※ Insert the black wire into “L” and tighten the screw (Picture 3) ※ Insert the white wire into “N” and tighten the
ページ9に含まれる内容の要旨
CONTROL PANEL INSTRUCTION 1. Press “POWER”to switch on or off. 2.“TIME”refers to control of operating time and indicates the amount of time remaining. ※Once power is on, the default amount of operating time is at 45 minutes. ※Press “UP” and “DOWN” to adjust and set time of use; pressing once will increase or reduce in 5 minute increments. The maximum operating time is 60 minutes. ※After time of use is set, the number will flash for about three seconds. ※After the set “Time”
ページ10に含まれる内容の要旨
OPERATING INSTRUCTIONS FOR COLOR LIGHT THERAPY SYSTEM 1. To activate the color light therapy system press “ADJUST” on the sauna control panel. Upon turning the system on, the color light system will go into an automatically cycling mode, changing color every 8 seconds: 2. Press “ADJUST” 2X: Light system will glow GREEN 3. Press “ADJUST” 3X: Light system will glow RED 4. Press “ADJUST” 4X: Light system will glow BLUE 5. Press “ADJUST” 5X: Light system will glow YELLOW
ページ11に含まれる内容の要旨
WARNINGS AND SUGGESTIONS FOR USE Please read carefully the following warnings, to reduce the risk of burns, fire, electric shock, or injury to persons: ※Do not put the sauna room in a moist environment. ※Place room on level surface. ※Do not repair the product by yourself. Contact the Saunatec National Customer Service Center toll-free at 1-888-780-4427, or email at techsupport@saunatec.com ※Do not disassemble the product by yourself except as indicated in the manual. ※Do not spray the
ページ12に含まれる内容の要旨
IG-520-BH-2 5/25/07
ページ13に含まれる内容の要旨
IG-520-BH-2 5/25/07
