ページ1に含まれる内容の要旨
OPERATOR’S MANUAL
1/2 in./18 VOLT DRILL-DRIVER
2-SPEED
P206
Your drill-driver has been engineered and manufactured to our high standard for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using
this product.
Thank you for your purchase.
SAVE THIS MANUAL FOR FUTURE REFERENCE
�
2 0
2 4
ページ2に含まれる内容の要旨
TABLE OF CONTENTS n Introduction ..................................................................................................................................................................... 2 �n General Safety Rules.................................................................................................................................................... 3-4 �n Specific Safety Rules...................................................................................................
ページ3に含まれる内容の要旨
GENERAL SAFETY RULES n Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enable better WARNING! control of the tool in unexpected situations. READ AND UNDERSTAND ALL INSTRUCTIONS. Fail- n Use safety equipment. Always wear eye protection. ure to follow all instructions listed below, may result in Dust mask, non-skid safety shoes, hard hat, or hearing electric shock, fire and/or serious personal injury. protection must be used for appropriate conditi
ページ4に含まれる内容の要旨
GENERAL SAFETY RULES n When servicing a tool, use only identical replacement SERVICE parts. Follow instructions in the Maintenance section n Tool service must be performed only by qualified re- of this manual. Use of unauthorized parts or failure to fol- pair personnel. Service or maintenance performed by low Maintenance Instructions may create a risk of shock unqualified personnel may result in a risk of injury. or injury. SPECIFIC SAFETY RULES n Hold tool by insulated gripping surfaces whe
ページ5に含まれる内容の要旨
SAFETY RULES FOR CHARGER n An extension cord should not be used unless absolutely necessary. Use of improper extension WARNING! cord could result in a risk of fire and electric shock. If READ AND UNDERSTAND ALL INSTRUCTIONS. extension cord must be used, make sure: Failure to follow all instructions listed below, may result in a. That pins on plug of extension cord are the electric shock, fire and/or serious personal injury. same number, size and shape as those of plug on charger. n Befo
ページ6に含まれる内容の要旨
SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta- tion of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power min Minutes Time Alternating Current Type of current Direct Current Type or a characteristic of current n No Load Speed Rotational speed, at no load o Class II Construction Doub
ページ7に含まれる内容の要旨
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING Indicates an imminently hazardous situation, which, if not avoided, will DANGER: result in death or serious injury. Indicates a potentially hazardous situation, which, if not avoided, could WARNING: result in death or serious injury. Indicates a potentially hazardous situation, which, if not avoided, may result CAUTION: in minor or moderate injury.
ページ8に含まれる内容の要旨
FEATURES PRODUCT SPECIFICATIONS Chuck .......................................................... 1/2 in. Keyless Clutch.................................................................24 position Motor..................................................................18 Volt DC Torque.................................................. Maximum 330 in.lb. Switch..........................................................Variable Speed Charger Input ................................... 120 V, 60 Hz, AC
ページ9に含まれる内容の要旨
FEATURES KNOW YOUR DRILL-DRIVER LEVELS See Figure 1. Levels are located on the top and end of the motor housing to help keep the drill bit level during use. Before attempting to use this product, familiarize yourself with all operating features and safety rules. MAG TRAY™ BIT STORAGE The magnetic tray conveniently stores screws or other small parts. Bits provided with the drill can be placed in the storage area, located on the top of motor housing. TORQUE ADJUSTMENT RING DIRECTION OF ROTATI
ページ10に含まれる内容の要旨
OPERATION NOTE: Batteries will not reach full charge the first time they are charged. Allow several cycles (operation followed by WARNING: recharging) for them to become fully charged. Do not allow familiarity with tools to make you care- less. Remember that a careless fraction of a second is CHARGING A COOL BATTERY PACK sufficient to inflict serious injury. If battery pack is within normal temperature range, the red LED on charger will come on. NOTE: If the charger does not charge the batte
ページ11に含まれる内容の要旨
OPERATION CHARGING A HOT BATTERY PACK P110 When using the tool continuously, the batteries in the battery CHARGER GREEN LED pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge. When the battery pack becomes discharged and is hot, this will cause the green LED to come on instead of the red LED. After 30 minutes, reinsert the battery pack in the charger. If the green LED continues to remain on, return battery pack to
ページ12に含まれる内容の要旨
OPERATION DIRECTION OF ROTATION SELECTOR WARNING: (FORWARD/REVERSE/CENTER LOCK) REVERSE Battery tools are always in operating condition. There- fore, switch should always be locked when not in use or carrying at your side. SWITCH TRIGGER See Figure 5. To turn the drill ON, depress the switch trigger. To turn it OFF, release the switch trigger. VARIABLE SPEED The switch trigger delivers higher speed and torque with increased trigger pressure and lower speed with decreased trigger pressure. NO
ページ13に含まれる内容の要旨
OPERATION TWO-SPEED GEAR TRAIN TWO-SPEED LO See Figure 7. GEAR TRAIN (HI-LO) SPEED The drill has a two-speed gear train designed for drilling or driving at LO (1) or HI (2) speeds. A slide switch is located on 1 top of the drill to select either LO (1) or HI (2) speed. When 2 using drill in the LO (1) speed range, speed will decrease HI and unit will have more power and torque. When using drill SPEED in the HI (2) speed range, speed will increase and unit will have less power and torque. Use
ページ14に含まれる内容の要旨
OPERATION MAG TRAY™ See Figure 10. The magnetic tray conveniently stores screws or other small parts. INSTALLING BITS See Figure 11 - 12. n Lock the switch trigger by placing the direction of rotation selector in the center position. n Open or close the chuck jaws to a point where the open- ing is slightly larger than the bit size you intend to use. Also, raise the front of the drill slightly to keep the bit from falling out of the chuck jaws. MAG TRAY™ n Insert the drill bit. (SCREW HOLDER)
ページ15に含まれる内容の要旨
15 2 0 OPERATION DRILLING TOP VIEW See Figure 13 - 14. Levels are located on the top and end of the motor hous- ing to help keep the drill bit level during use. n Check the direction of rotation selector for the correct setting (forward or reverse).� n Secure the material to be drilled in a vise or with clamps to keep it from turning as the drill bit rotates.� n Hold the drill firmly and place the bit at the point to be drilled.� LEVEL n Depress the switch trigger to start the drill. n Move
ページ16に含まれる内容の要旨
MAINTENANCE WARNING: GENERAL MAINTENANCE Avoid using solvents when cleaning plastic parts. Most When servicing, use only identical Ryobi replacement plastics are susceptible to damage from various types of parts. Use of any other parts may create a hazard or commercial solvents and may be damaged by their use. Use cause product damage. clean cloths to remove dirt, dust, oil, grease, etc. WARNING: WARNING: Always wear safety goggles or safety glasses with side Do not at any time let brake f
ページ17に含まれる内容の要旨
MAINTENANCE CHUCK REMOVAL See Figures 15 - 17. MALLET The chuck may be removed and replaced by a new one. n Lock the switch trigger by placing the direction of rotation selector in center position. n Insert a 5/16 in. or larger hex key into the chuck of the CHUCK drill and tighten the chuck jaws securely. JAWS n Tap the hex key sharply with a mallet in a clockwise di- rection. This will loosen the screw in the chuck for easy removal. n Open the chuck jaws and remove the hex key. Using a scr
ページ18に含まれる内容の要旨
OPERATOR’S MANUAL 1/2 in./18 VOLT DRILL-DRIVER 2-SPEED P206 • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Authorized Service Center. Be sure to provide all pertinent facts when you call or visit. Please call 1-800-525-2579 for your nearest Authorized Service Center. You can also check our web site at www.ryobitools.com for a complete list of Authorized Service Centers. • MODEL NO. AND SERIAL NO. The model n
