ページ1に含まれる内容の要旨
Owner’s Manu
Read and understand this entire manual before riding!
DO NOT RETURN TO STORE!
NOTE: Manual illustrations are for demonstration purposes only.
Illustrations may not reflect exact appearance of actual product.
Specifications subject to change without notice.
Item Number:
E200 13112430
E200S 13112730
Version 1_01/10
E225 13112801
al
ページ2に含まれる内容の要旨
CONTENTS Safety Warnings ...............................................................1 Repair and Maintenance ................................................5-8 Before You Begin ..............................................................2 Troubleshooting Guide .................................................9-10 Assembly and Set-Up ....................................................3-4 Electric Scooter Parts .....................................................11 Hardware Maintenance
ページ3に含まれる内容の要旨
BEfORE yOU BEGIN Remove contents from box. Remove the foam separators that protect the components from damage during WARNING: shipping. Inspect the contents of the box for scratches in the paint, dents or kinked cables that may have DO NOT USE NON- occurred during shipping. Because the scooter is 95 percent assembled and packed at the factory, there RAZOR PRODUCTS WITH should not be any problems, even if the box has a few scars or dents. YOUR RAZOR ELECTRIC SCOOTER. The scooter has
ページ4に含まれる内容の要旨
ASSEMBLy AND SET-UP q Attaching the Handlebars WARNING: Failure to recharge the battery at least once a month may result in a battery that will no longer accept a charge. 1 Loosen the locking knob and 3 Slide the quill into the 2 Remove the plastic protec- WARNING: Failure swing to the 6 o’clock position tor covering the base of the fork until it bottoms on the to properly tighten the wedge to unfold the handlebar. headset. handlebar assembly. Insert the may allow the han
ページ5に含まれる内容の要旨
ASSEMBLy AND SET-UP Front Tire 4 Using a bicycle style tire pump equipped for a Schrader-type valve, inflate the front tire to the PSI indicated on the sidewall of the tire. q Attaching the Seat (if applicable) WARNING: Always disconnect your scooter from the charger before cleaning with liquid. 1 Attach the seat to the 2 Unscrew the four screws on 3 Place the seat post on the seat post with two 4mm key the middle of the deck with the deck and secure using the same Note: If you
ページ6に含まれる内容の要旨
CONNECTORS/HARDWARE MAINTENANCE Brake Safety Gear Check the brakes for proper function. When you squeeze the lever, Always wear proper protective gear such as an approved safety q q the brake should provide positive braking action. When you apply helmet. Elbow pads and kneepads are recommended. Always the brake with the speed control on, the brake cut-off switch wear athletic shoes (lace-up shoes with rubber soles), never ride should stop the motor. Make sure that brakes are not rubbing. b
ページ7に含まれる内容の要旨
REPAIR AND MAINTENANCE q Chain and Rear Tire Replacement Tools required: Phillips screwdriver, 10mm wrench, two (2) 8mm wrenches, and two (2) 17mm wrenches. 1 With a Phillips screwdriver, 2 With a 10mm wrench, 3 With two 8mm wrenches, loosen the two screws and loosen the brake cable anchor loosen brake housing anchor remove the chain guard. and disconnect the cable. and disconnect. Keep the spacer and bolts together. Right Side (Throttle) Spacer Washer (clipped) Washer (plate cut) Axle
ページ8に含まれる内容の要旨
REPAIR AND MAINTENANCE 10 Install the axle adjusters 11 Tighten both axle adjusters 12 Tighten the brake housing and axle nuts. Tighten until they the same number of turns to fine- anchor securely. Test ride and just barely hold the hardware tune the tension on the chain and check. Readjust as needed. in place. center the wheel. 13 Replace the chain guard. q front Tire Replacement Tools required: two (2) 17mm wrenches and a flathead screwdriver. 8-1 Right Side (Throttle) 8-3 8-3 - (Short)
ページ9に含まれる内容の要旨
REPAIR AND MAINTENANCE Note: This system of adjusters q Adjusting the Chain is common to motorcycles Tools required: 10mm wrench, two (2) 8mm wrenches, and two (2) 17mm wrenches. and BMX bicycles. If you are not familiar with it or do not feel comfortable performing the adjustment, consult an authorized Razor service center or a qualified BMX bike or motorcycle mechanic. The chain should be “just taut” – in other words snug, but not piano-wire tight. The tension should be similar
ページ10に含まれる内容の要旨
TROUBLESHOOTING GUIDE Problem Possible Cause Solution Undercharged battery Charge the battery. A new battery should be charged for at least 18 Scooter does not run hours before using the scooter for the first time and up to 12 hours after each subsequent use. Loose wires or connectors Check all connectors. Make sure the charger connector is tightly plugged into the charging port, and that the charger is plugged into the wall. Tripped circuit breaker Check all wires and connectors to mak
ページ11に含まれる内容の要旨
E200 / E200S SCOOTER PARTS Keep your scooter running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability. (Specifications subject to change without notice.) 1 Handlebar grips (right/left) 4 Brake lever assembly 13 Control module 1-1 Valve extender 5 Headset (upper/lower) 14 Battery (2-12V/7Ah) 1-2 Handlebar end cap 6 Front fork 15 Motor - 250W 2 Single speed twist-grip throttle 7 Limiter 16 Kickstand 2-1 Sleeve 8 F
ページ12に含まれる内容の要旨
SB 1918 (CALIFORNIA) DECLARATION YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC VEHICLE. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT. 11
ページ13に含まれる内容の要旨
WARRANTy Razor does not offer an extended warranty. If you have purchased an Razor Limited Warranty extended warranty, it must be honored by the store at which it was The manufacturer warranties this product to be free of manufacturing defects purchased. for a period of 90 days from date of purchase. This Limited Warranty does not cover normal wear and tear, tires, tubes or cables, or any damage, failure For your records, save your original sales receipt with this manual and write or los
