ページ1に含まれる内容の要旨
49-2020.fm Page 1 Wednesday, August 18, 1999 2:57 PM
Cat. No. 49-2020
OWNER’S MANUAL
Please read before using this equipment.
Smoke Alarm
Siren Detector
for use with the SAFE HOUSE
Wireless Alarm System
(Cat. No. 49-2010/49-2011)
ページ2に含まれる内容の要旨
49-2020.fm Page 2 Wednesday, August 18, 1999 2:57 PM INTRODUCTION Your Radio Shack Smoke Alarm Si- ren Detector gives you extra protec- tion if a smoke alarm is out of normal hearing range. The detector listens for the siren from the smoke alarm. When the detector hears the siren, it sends a signal to the base, which sounds the system’s alarm. © 1997 Tandy Corporation. All Rights Reserved. Radio Shack is a registered trademark used by Tandy Corporation. 2
ページ3に含まれる内容の要旨
49-2020.fm Page 3 Wednesday, August 18, 1999 2:57 PM Notes: • The siren detector does not detect smoke. It only detects the sound from a smoke alarm. • We suggest you use a Radio Shack Cat. No. 49-466 Smoke Alarm with the siren detector. Other smoke alarms might not work properly. • Be sure you test the siren detec- tor as described under “Testing” on Page 12. 3
ページ4に含まれる内容の要旨
49-2020.fm Page 4 Wednesday, August 18, 1999 2:57 PM This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) the device may not cause harmful inter- ference, and (2) the device must accept any interference received, including interference that may cause undesired operation. 4
ページ5に含まれる内容の要旨
49-2020.fm Page 5 Wednesday, August 18, 1999 2:57 PM INSTALLATION INSTALLING THE BATTERY 1. Slide off the battery compartment cover. 2. Connect a 9-volt alkaline battery (Cat. No. 23-553) to the battery connector. Then place the bat- tery in the compartment. illustration 5
ページ6に含まれる内容の要旨
49-2020.fm Page 6 Wednesday, August 18, 1999 2:57 PM 3.Replace the battery compart- ment cover. Note: Changing the detector’s bat- tery sometimes triggers the fire alarm. If this happens, turn off the alarm system then turn it on again. 6
ページ7に含まれる内容の要旨
49-2020.fm Page 7 Wednesday, August 18, 1999 2:57 PM CONNECTING TO THE SYSTEM Follow these steps to add the siren detector to your alarm system. 1. Press LEARN on the system’s base. The LEARN indicator flashes. illustration 2. Enter your access code on the base’s keypad. The LEARN indi- cator lights and the next avail- able zone’s indicator flashes. 7
ページ8に含まれる内容の要旨
49-2020.fm Page 8 Wednesday, August 18, 1999 2:57 PM 3. Press TEST on the siren detector. The system stores the detector’s settings in the next available zone, lights the zone’s indicator, and sounds a brief tone. Note: To assign the siren detec- tor to a zone other than the next available zone, enter the desired zone number. For example, to assign the detector to Zone 5, press 05. Then press TEST on the detector. 8
ページ9に含まれる内容の要旨
49-2020.fm Page 9 Wednesday, August 18, 1999 2:57 PM MOUNTING THE DETECTOR To ensure the siren detector de- tects the smoke alarm when it sounds, mount the detector 4–6 inches from a UL-approved smoke alarm (Cat. No. 49-466). Follow these steps to mount the de- tector. 1. At the desired mounting location, 3 drill two holes 1 /4 inches apart, one above the other. 9
ページ10に含まれる内容の要旨
49-2020.fm Page 10 Wednesday, August 18, 1999 2:57 PM 2. Thread the supplied screws into the holes until each screw’s head 1 extends about /4 inch from the wall. 3. Line up the keyhole slots on the detector with the screws on the mounting location, then slide the detector down onto the screws until it is secure. After you mount the siren detector, be sure you test it as described un- der “Testing” on Page 12. 10
ページ11に含まれる内容の要旨
49-2020.fm Page 11 Wednesday, August 18, 1999 2:57 PM Notes: • The siren detector can also detect other loud sounds (ste- reos, musical instruments, and so on). Be sure you mount the detector in a location that mini- mizes false alarms. • If the battery is not installed, the red safety tab inside the detector prevents you from mounting the detector. 11
ページ12に含まれる内容の要旨
49-2020.fm Page 12 Wednesday, August 18, 1999 2:57 PM TESTING To test the siren detector, hold down the smoke alarm’s test button until its siren sounds. The indicator on the siren detector flashes briefly and the base sounds an alarm. Press CANCEL on the base to si- lence the base’s alarm. Notes: • You might have to hold down the smoke alarm’s test button for as long as 15 seconds. The siren detector has a delay function to help prevent false alarms. • We suggest you perform this test once a
ページ13に含まれる内容の要旨
49-2020.fm Page 13 Wednesday, August 18, 1999 2:57 PM UNINSTALLING Follow these steps to remove the siren detector. 1. Press LEARN on the base. Then enter your access code. illustration 2. Enter the zone number for the siren detector. The correspond- ing zone indicator flashes. CANCEL 3. Press on the base while the indicator flashes. The indica- tor turns off. 4. Press CANCEL again. 13
ページ14に含まれる内容の要旨
49-2020.fm Page 14 Wednesday, August 18, 1999 2:57 PM NOTES 14
ページ15に含まれる内容の要旨
49-2020.fm Page 15 Wednesday, August 18, 1999 2:57 PM 15
ページ16に含まれる内容の要旨
49-2020.fm Page 16 Wednesday, August 18, 1999 2:57 PM Radio Shack Limited Warranty This security product is warranted against manufacturing defects in material and workmanship for ninety (90) days from the date of purchase from Radio Shack company owned stores and authorized Radio Shack franchisees and dealers. Within this period Radio Shack will repair the security product without charge for parts and labor. Simply bring your Radio Shack sales slip as proof-of-purchase date to any Radio Shac
