ページ1に含まれる内容の要旨
Model No. PFBE3006.0
USER’S MANUAL
Serial No.
Write the serial number in the
space above for reference.
Serial Number Decal (under seat)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if a part is
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-888-533-1333
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
www.proformservice.com
CAUTION
Visit our website at
Read all precautions and
ページ2に含まれる内容の要旨
TABLE OF CONTENTS WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ASSEMBLY . . . . . . .
ページ3に含まれる内容の要旨
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precautions before using the weight bench. 1. Read all instructions in this manual and all 10. Always make sure that the backrest knob is warnings on the weight bench before using fully inserted into the backrest frame before the weight bench. Use the weight bench only exercising. as described in this manual. 11. Make sure that the cables remain on the pul- 2. It is the responsibility of the owner
ページ4に含まれる内容の要旨
BEFORE YOU BEGIN ® Thank you for selecting the versatile PROFORM model number and serial number before contacting us. FUSION 3.0 XT weight bench. The FUSION 3.0 XT The model number is PFBE3006.0. The serial number weight bench is designed to help develop every major can be found on a decal attached to the weight bench muscle group of the body. Whether your goal is to tone (see the front cover of this manual). your body, build dramatic muscle size and strength, or improve your cardiovascular syst
ページ5に含まれる内容の要旨
ASSEMBLY • As you assemble the weight bench, make sure all Make Assembly Easier parts are oriented as shown in the drawings. Everything in this manual is designed to ensure • Tighten all parts as you assemble them, unless that the weight bench can be assembled suc- instructed to do otherwise. cessfully by anyone. Most people find that by setting aside plenty of time, assembly will go • For help identifying small parts, use the PART smoothly. IDENTIFICATION CHART. Before beginning assembly, c
ページ6に含まれる内容の要旨
2. Attach the remaining Bench Foot (15) to the 2 Center Seat Base (1) with two M4 x 16mm Self- tapping Screws (91) and two M4 Washers (84). 15 1 84 84 91 3. Insert two M10 x 100mm Screws (26) up through 3 the Base Plate (34), the Center Seat Base (1), and the Right and Left Seat Bases (2, 3). 2 Attach the Right and Left Seat Bases (2, 3) to the Center Seat Base (1) with two M10 x 58mm 95 Button Bolts (95) and two M10 Nylon Locknuts (77). 1 3 34 77 26 4. Attach the Seat Frame (5) to the Center
ページ7に含まれる内容の要旨
5. Attach the Backrest (11) to the Backrest Frame 5 (8) with four M6 x 25mm Button Screws (17). 11 17 8 17 6. Apply a small amount of the included grease to 6 an M10 x 87mm Button Bolt (94). Attach the Backrest Frame (8) to the Seat Frame (5) with the Button Bolt and an M10 Nylon Locknut (77). Do not overtighten the Nylon Locknut; the Backrest Frame should pivot easily. Engage the Backrest Knob (22) into one of the holes in the Backrest Frame (8), and fully tighten the Backrest Knob into the Sea
ページ8に含まれる内容の要旨
8. Attach the Seat (12) to the Seat Frame (5) with 8 four M6 x 72mm Button Screws (92) and four M6 Washers (81). 12 5 81 92 92 9. Insert a Pad Tube (10) into the Leg Lever (6). 9 Slide two Foam Pads (14) onto the Pad Tube. Assemble the other two Pad Tubes (10) to the Leg Lever (6) and the Seat Frame (5) in the same manner. 5 14 10 14 6 14 10 10 14 10. Attach the Curl Pad (13) to the Curl Post (7) with 10 two M6 x 25mm Button Screws (17). 13 7 17 8
ページ9に含まれる内容の要旨
11. Attach the Left Rack Base (37) to the Center 11 Rack Base (39) with two M10 x 67mm Bolts (86), an M10 Washer (80), and an M10 Nylon Locknut (77). Do not tighten the Bolts yet. 86 Repeat this step with the Right Rack Base (38). 38 80 39 77 37 12. Attach the Rear Rack Base (40) to the Rear 12 Upright (41) with two M10 x 67mm Bolts (86), two M10 Washers (80), and an M10 Nylon Locknut (77). Do not tighten the Bolts yet. 86 41 77 80 40 13. Attach the Foot Plate (49) and the Rear Rack 13 Base (40)
ページ10に含まれる内容の要旨
14. Insert an M10 x 20mm Bolt (89) into the Weight 14 Carriage (42) from the side shown. 89 Slide the Weight Carriage Stop (58) onto the Rear Upright (41). Then, slide the Weight Carriage (42) onto the Rear Upright. 42 58 41 15. Attach a Guide Rod (46) to the Left Rack Base 15 (37) with an M8 x 53mm Bolt (9), two M8 38 Washers (83), an 11mm x 8mm Spacer (82), and an M8 Nylon Locknut (78). Do not tighten the 46 Nylon Locknut yet. Attach a Guide Rod (46) to the Right Rack Base (38) in the same ma
ページ11に含まれる内容の要旨
17. Attach a Front Upright (43) to the Right Rack 17 Base (38) with two M10 x 82mm Bolts (85), two 88 M10 Washers (80), and an M10 Nylon Locknut (77). Do not tighten the Bolts yet. Attach the Front Upright (43) to the right Guide Rod (46) with an M10 x 25mm Bolt (88). 46 Repeat this step with the other Front Upright (not shown). 43 77 80 38 85 18. Attach the Cross Frame (44) to the right Front 18 Upright (43) with two M10 x 82mm Bolts (85), two 80 M10 Washers (80), and an M10 Nylon Locknut 85 (7
ページ12に含まれる内容の要旨
20. Orient the Locking Bar (50) as shown. Slide the 20 Barbell (51) through the Left Barbell Guide (52), the Locking Bar, and the Right Barbell Guide (53). 53 Make sure that the Barbell is centered in the Barbell Guides. Engage the Locking Bar into the 50 Uprights (43) at the lowest position. Hole 52 43 51 21. Hand tighten an M8 x 20mm Button Screw (16) 21 into the Left Barbell Guide (52). Slide a Weight Stop (69) onto the Barbell (51). 41 Hand tighten an M6 x 15mm Button Screw (96) 59 into th
ページ13に含まれる内容の要旨
24. Route the Cable (61) under a Pulley (63). Attach 24 the Pulley, a Cable Trap (66), and two Half Finger Guards (65) to the two Pulley Plates (35) with an M10 x 50mm Bolt (79) and an M10 Nylon Locknut 77 (77). Make sure that the Cable Trap is oriented 61 to hold the Cable in the groove of the Pulley. 63 65 65 35 66 79 35 25. Route the Cable (61) over a Pulley (63). Attach 25 the Pulley inside the Top Frame (45) with an M10 x 78mm Bolt (87) and an M10 Nylon Locknut 45 77 (77). 87 63 61 26. Att
ページ14に含まれる内容の要旨
29. Attach the Cable (61) to the Rear Rack Base (40) 29 61 with an M10 x 67mm Bolt (86), two M10 Washers (80), and an M10 Nylon Locknut (77). 77 80 40 80 86 30. Make sure that all parts are properly tightened. The use of the remaining parts will be explained in ADJUSTMENTS starting below. ADJUSTMENTS This section explains how to adjust the weight bench. See the EXERCISE GUIDELINES on page 18 for impor- tant information about how to get the most benefit from your exercise program. Also, refer to
ページ15に含まれる内容の要旨
ATTACHING ACCESSORIES The Lat Bar (55) can be attached to a Cable (61) with a Cable Clip (71). For some exercises the Chain (24) 61 should be attached between the Cable and the Lat 71 Bar with two Cable Clips. 24 The other accessories can be attached to the Cables (61) in the same manner. 71 55 ATTACHING THE BARBELL ADAPTERS Slide a Barbell Adapter (54) onto the Barbell (51) and secure it in place with an M8 x 10mm Set Screw (62). Repeat this process on the other side of the 62 Barbell. 51 54 AD
ページ16に含まれる内容の要旨
ADJUSTING THE BARBELL STOPS 51 Hold the handle on a Barbell Stop Hook (48) and dis- engage the Barbell Stop Hook from the Front Upright (43). Move the Barbell Stop (47) to the lowest point you want the Barbell (51) to go to during the exercise. Reengage the Hook into the Upright. Repeat with the 43 other Barbell Stop. 48 Handle 47 WARNING: Always set both Barbell Stops (47) at the same height. USING THE BARBELL 51 First, attach the desired amount of weight to the Barbell (51) (see ADDING WEIGHT
ページ17に含まれる内容の要旨
CABLE DIAGRAM The cable diagram shows the proper routing of the cables. Use the diagram to make sure that the cables 2 4 and the cable traps have been assembled correctly. If the cables have not been correctly routed, the weight bench will not function properly and damage may 1 occur. The numbers show the correct route for each cable. Make sure that the cable traps do not touch or bind the cables. 3 2 5 1 3 17
ページ18に含まれる内容の要旨
EXERCISE GUIDELINES THE FOUR BASIC TYPES OF WORKOUTS PERSONALIZING YOUR EXERCISE PROGRAM Muscle Building Determining the exact length of time for each workout, To increase the size and strength of your muscles, as well as the number of repetitions or sets completed, push them close to their maximum capacity. Your mus- is an individual matter. It is important to avoid overdo- cles will adapt and grow as you progressively increase ing it during the first few months of your exercise pro- the intens
ページ19に含まれる内容の要旨
Rest for a short period of time after each set. The slowly as you stretch and do not bounce. Ease into ideal resting periods follow: each stretch gradually and go only as far as you can • Rest for three minutes after each set for a muscle without strain. Stretching at the end of each workout building workout. is an effective way to increase flexibility. • Rest for one minute after each set for a toning work- out. STAYING MOTIVATED • Rest for 30 seconds after each set for a weight loss workout. F
ページ20に含まれる内容の要旨
PART IDENTIFICATION CHART Refer to the drawings below to identify small parts used in assembly. The number in parentheses by each draw- ing is the key number of the part, from the PART LIST in the center of this manual. Note: Some small parts may have been preassembled. If a part is not in the parts bag, check to see if it has been preassembled. If a part is missing, call toll-free 1-888-533-1333. M10 x 50mm Bolt (79) M6 Washer (81) M8 Washer (83) M10 Washer (80) M8 x 53mm Bolt (9) M4 Washer (84
