ページ1に含まれる内容の要旨
IMPORTANT MANUAL Do Not Throw Away
OPERATOR'S MANUAL
MODEL:
WARNING:
Read this Man u al and follow all Warn-
ings and Safety Instructions. Fail ure
PRRT900
to do so can re sult in serious in ju ry.
REAR TINE TILLER
ALWAYS WEAR EYE PROTECTION DURING OPERATION
Visit our website: www.poulanpro.com
Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine.
The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty.
11.08.11
ページ2に含まれる内容の要旨
SAFETY RULES Safe Operation Practices for Walk-Behind Powered Ro ta ry Tillers • Do not overload the machine capacity by attempting TRAINING to till too deep at too fast a rate. • Read the Manual care ful ly. Be thor ough ly fa mil iar with • Never operate the machine at high speeds on slippery the controls and the proper use of the equip ment. Know surfaces. Look behind and use care when backing. how to stop the unit and disengage the controls quickly. • Never allow bystanders near the unit
ページ3に含まれる内容の要旨
CUSTOMER RESPONSIBILITIES PRODUCT SPECIFICATIONS • Read and observe the safety rules. Gasoline Capacity: 2.9 Quarts (2,7L) • Follow a regular schedule in maintaining, caring for Unleaded Reg u lar and using your tiller. OIL (API:SG-SL): SAE 30 Above 32°F/0°C • Follow instructions under “Maintenance” and “Stor age” (Capacity 20 oz/0,6L) sections of this Manual. SAE 5w30 Below 32°F/0°C IMPORTANT: THIS UNIT IS EQUIPPED WITH AN INTERNAL Spark Plug: Champion RC12YC COMBUSTION ENGINE
ページ4に含まれる内容の要旨
ASSEMBLY Your new tiller has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tiller all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. TOOLS REQUIRED FOR ASSEMBLY FRONT A socket wrench set will make assembly easier. Standard wrench sizes are listed. (1) Utility knife (1) Tire pressure gauge (1) Pair of pliers LEFT RIGHT
ページ5に含まれる内容の要旨
ASSEMBLY • Grasp handle assembly. Hold in “up” position. Be sure UNPACKING CARTON (See Fig. 2) handle lock remains in gearcase notch. Slide handle assembly into position. CAUTION: Be careful of exposed sta ples when handling or disposing of cartoning material. HANDLE ASSEMBLY "UP" POSITION IMPORTANT: WHEN UN PACK ING AND ASSEM BLING TILLER, BE CAREFUL NOT TO STRETCH OR KINK CABLES. TIGHTEN HANDLE LOCK • While holding handle assembly, cut cable ties se cur ing LEVER TO HOLD handle ass
ページ6に含まれる内容の要旨
ASSEMBLY CONNECT SHIFT ROD (See Fig. 6) • Insert end of shift rod into hole of shift lever indicator. • Insert hairpin clip through hole of shift rod to secure. SHIFT HAIRPIN SHIFT LEVER CLIP ROD INDICATOR Fig. 6 REMOVE TILLER FROM CRATE • Make sure shift lever indicator is in “N” position (See Fig. 6) • Tilt tiller forward by lifting handle. Separate cardboard cover from leveling shield. • Rotate tiller handle to the right and pull tiller out of carton. CHECK TIRE PRESSURE The tires on your
ページ7に含まれる内容の要旨
OPERATION KNOW YOUR TILLER READ THIS MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER. Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your Tiller or in literature supplied with the product. Learn and understand their meaning. TINE CONTROL SHIFT LEVER CHOKE CONTROL THROTTLE CONTROL SHIFT LEVER IN DI CA TOR DEPTH STAKE LEVELING SHIELD OUTER SIDE REC
ページ8に含まれる内容の要旨
OPERATION The operation of any tiller can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tiller and while tilling. We recommend a wide vision safety mask for over spectacles or standard safety glasses. 00155 HOW TO USE YOUR TILLER Know how to operate all controls before adding fuel and SHALLOWEST oil or attempting to start engine. TILLING TRANSPORT (CULTIVATING) POSITION STOPPING (See Fig.
ページ9に含まれる内容の要旨
OPERATION • When you have completed your turn-around, release ADD GASOLINE the tine control and lower handle. Place shift lever in • Fill to within 1/2" of top of fuel tank to prevent spills and till position and move throttle control to de sired speed. to allow for fuel expansion. Do not overfill. Use fresh, To begin tilling, hold tine control against the handle. clean, regular un lead ed gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon TO TRANSPO
ページ10に含まれる内容の要旨
engine_art_71 OPERATION NOTE: A warm engine requires less choking to start. • Soil conditions are important for proper tilling. Tines will • Move throttle control to desired running position. not readily penetrate dry, hard soil which may con trib ute to excessive bounce and difficult handling of your tiller. • Allow engine to warm up for a few minutes before Hard soil should be mois tened before tilling; however, engaging tines. extremely wet soil will “ball-up” or clump during tilling.
ページ11に含まれる内容の要旨
MAINTENANCE MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE SERVICE DATES REGULAR SERVICE Check Engine Oil Level Change Engine Oil 1,2 Oil Pivot Points Inspect Spark Arrester / Muffler Inspect Air Screen Clean or Replace Air Cleaner Cartridge 2 Clean Engine Cylinder Fins Replace Spark Plug RH Gear Case Grease Fitting (1oz.) 1 - Change more often when operating under a heavy load or in high ambient temperatures. 2 - Service more often when operating in dirty or dusty conditions. LUBRICATION C
ページ12に含まれる内容の要旨
MAINTENANCE Disconnect spark plug wire before performing any maintenance (except car bu re tor adjustment) to prevent accidental start ing of engine. Prevent fires! Keep the engine free of grass, leaves, spilled oil, or fuel. Re move fuel from tank before tipping unit for maintenance. Clean muffler area of all grass, dirt, and debris. Do not touch hot muffler or cylinder fins as contact may cause burns. ENGINE LUBRICATION Use only high quality detergent oil rated with API service classifi
ページ13に含まれる内容の要旨
engine_art_71 MAINTENANCE COOLING SYSTEM (See Fig. 18) Your engine is air cooled. For proper engine performance and long life keep your engine clean. • Clean air screen frequently using a stiff-bristled brush. • Keep cylinder fins, levers, and linkage free of dirt and chaff. CYLINDER FINS BLOW ER HOUS ING MUFFLER AIR SCREEN Fig. 18 MUFFLER Do not operate tiller without muffler. Do not tamper with exhaust system. Damaged mufflers or spark arresters could create a fire hazard. Inspect pe
ページ14に含まれる内容の要旨
SERVICE AND ADJUSTMENTS CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug. TILLER TO ADJUST HANDLE HEIGHT (See Fig. 19) Select handle height best suited for your tilling conditions. CLEVIS PIN Handle height will be different when tiller digs into soil. • First loosen handle lock lever. • Handle can be positioned at different settings between “HIGH” and “LOW” positions. • Retighten handle lock lever securely after adjusting. HANDL
ページ15に含まれる内容の要旨
SERVICE AND ADJUSTMENTS TO REPLACE GROUND DRIVE BELT GROUND DRIVE BELT ADJUSTMENT (See Fig. 21 and 22) (See Fig. 22) • Remove belt guard (See “TO REMOVE BELT GUARD” For proper belt tension, the extension spring should have in this section of this manual). about 5/8" stretch when tine control is in “EN GAGED” posi- • Remove old belt by slipping off engine pulley first then tion. This tension can be attained as follows: remove from transmission pulley. • Loosen cable clip screw securing t
ページ16に含まれる内容の要旨
SERVICE AND ADJUSTMENTS • To maintain the superb tilling performance of this TINE REPL ACEMENT (See Figs. 23, 24 and 25) ma chine the tines should be checked for sharpness, wear, and bending, particularly the tines which are CAUTION: Tines are sharp. Wear next to the transmission. If the gap between the tines gloves or other protection when han- ex ceeds 3-1/2" they should be replaced or straight ened dling tines. as necessary. • New tines should be assembled as shown in Fig. A bad
ページ17に含まれる内容の要旨
SERVICE AND ADJUSTMENTS ENGINE TO AD JUST CARBURETOR The carburetor has been preset at the factory and ad just ment should not be necessary. However, engine per for mance can be affected by dif fer enc es in fuel, tem per a ture, al ti tude or load. If the carburetor does need ad just ment, contact your nearest authorized service center/de part ment IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVER SPEED ING THE ENGINE ABOVE THE FACTO
ページ18に含まれる内容の要旨
STORAGE Immediately prepare your tiller for storage at the end of the ENGINE OIL season or if the unit will not be used for 30 days or more. Drain oil (with engine warm) and replace with clean oil. (See “ENGINE” in the Maintenance section of this man ual). WARNING: Never store the tiller with gasoline in the tank inside a build ing CYLINDER(S) where fumes may reach an open flame • Remove spark plug. or spark. Allow the engine to cool before • Pour 1 ounce (29 ml) of oil through spark pl
ページ19に含まれる内容の要旨
TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly. 2. See “TO START ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Dirty air cleaner. 4. Clean or replace air cleaner cartridge. 5. Water in fuel. 5. Empty fuel tank and carburetor, and refill tank with fresh, clean gasoline. 6. Clogged fuel tank. 6. Remove fuel tank and clean. 7.
ページ20に含まれる内容の要旨
LIMITED WARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in mate- rials and work man ship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or replace, at our option, without charge for parts or labor incurred in replacing parts, any part which we find to be defective due to materials or workmanship. This Warranty is subject to the following limitations and exclusio
