ページ1に含まれる内容の要旨
I:)E}F604
Volume 2
Optional Shroud Kit
S EMB L Y
NSTRUCTIOHS
625
D Y
O
A B
P A R
B Y
Our Strength Begins With Listening.
ページ2に含まれる内容の要旨
!!I llI IMPORTANT .WARNING... KEEP ALL FRAME BOLT CONNECTIONS LOOSE UNTIL INSTRUCTED IN MAKE SURE SNAP HOOKS ARE FASTENED BEFORE DOING EXERaSES. THE ASSEMBLY STEP SEQUENCES TO SECURELY TIGHTEN. !!!WARNING!!!- ¯ NOTE:The ParaBody Factor 625 base unit must be assembled on LAT BAR IS NOT TO BE USED FOR PULL-UPS. a flat, level surface to assure its proper function. ¯ ParaBody strongly recommends that this product be assembled NOTE: We recommend cleaning your product (pads and the frame members) on a
ページ3に含まれる内容の要旨
Do not mark this box! Document: 11000199
ページ4に含まれる内容の要旨
PARAB6DY INC. FACTOR 625 D-RING RETRO KIT 607/608 PRODUCT ASSEMBLY INSTRUCTION SHEETS TOOLS REQUIRED FOR ASSEMBLY RATCHET 9/16 INCH SOCKET 7/16 INCH WRENCH ADJUSTABLE WRENCH REVISION: A If you experience any problem with the assembly of this product, please contact yo~ar dealer or your PARABODY Customer Service Representative at: 1-800-328-9714
ページ5に含まれる内容の要旨
607/608 FACTOR 625 D-RING RETRO KIT ASSEMBLY PARTS LIST HARDWARE/PARTS: QT~( ITEM NAME/DESCRIPTION 1 (6352301) ........................ ~ ............... D-RING WLDMNT ........................................................ I (6406001) ........................................ ROTARY CABLE .......................................................... 2. 1 (6405701) ....................................... LEG PRESS/ROTARY CABLE ..................................... 3. 1 ~ ........ (6406101) ........
ページ6に含まれる内容の要旨
FACTOR 625 D-RING RETRO KIT ASSEMBLY INSTRUCTIONS 607/608 STEP 1: D-RING’INSTALLATION To assemble the new D-RING to the FACTOR 625, use the following steps: 1. ¯ Remove all the CABLES from the old D-RING. ¯ Loosen, and remove the two (2) 1/4-20 NUTS, and the 1/4 IN. WASHER from the end of the RING CABLE. ¯ Slide one (1) VINYL CAP over the end of the new D-RING. ¯ Remove and discard old D-RING, and replace with the new D-RING. ¯ LOOSELY attach the 1/4 IN. WASHER, and the two (2) 1/4 IN. NUTS to
ページ7に含まれる内容の要旨
607/608 FACTOR 625 D-RING RETRO KIT ASSEMBLY INSTRUCTIONS Replace the remaining CABLES in the following’or~er using the steps outlined in STEP 2: (PLEASE 3. REPLACE ONE CABLE AT A TIME, REPLACING IN A CLOCKWISE DIRECTION AROUND THE D-RING. SEE DRAWING) ¯ PEC/D-RING CABLE (6406101) ¯ MULTI PRESS CABLE (6405801) ¯ LAT CABLE (6405901) When all of the CABLES have been replaced, adjust the height of the D-RING on the D-RING CABLE by raising or lowering the two (2) 1/4-28 IN. NUTS. (THE D-RING SHOULD
ページ8に含まれる内容の要旨
ページ9に含まれる内容の要旨
