ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
89310! PROSYSTEM ASSEMBLY INSTRUCTIONS Attach one (I) I-1/4 SQ. RUBBER BUMPER to the CENTER of the CARRIAGE STOP on the WEIGHT CARRIAGE. Slide WEIGHT CARRIAGE down over the REAR UPRIGHT of the MAIN UPRIGHT. (NOTE: MAKE SURE THAT THE WEIGHT PEG ON THE WEIGHT CARRIAGE IS FACING TOWARDS THE FRONT OF THE MACHINE) LOOSELY attach the two (2) PULLEY MOUNT FLATS to the REAR and FRONT UPRIGHTS of the MAIN UPRIGHT. using two (2) 3/8 X 3 IN. BOLTS, two (2) 3/8 IN. LOCI(. WASHERS, and two (2) IN. NUTS. (NO
ページ4に含まれる内容の要旨
-.1 ~---. 0 ~0 ~ o ~0 ~Z ~ = r-i
ページ5に含まれる内容の要旨
ページ6に含まれる内容の要旨
0 0 0 0 0 0 0 q~0 0 0 0__0~0. 0 ;. . 000000;~00000
ページ7に含まれる内容の要旨
x 0 z c~ c -0 0 z z r- 0 c ~ 0 "r 4~Z ~
ページ8に含まれる内容の要旨
Do not mark this box! Document: 11000258
ページ9に含まれる内容の要旨
893102 PROSYSTEM. PRODUCT ASSEMBLY INSTRUCTIONS SHEETS 1 12/06/95
ページ10に含まれる内容の要旨
893102 PROSYSTEM ASSEMBLY PARTS LIST SORT AND COUNT ALL PARTS BEFORE BEGINNING ASSEMBLY HARDWARE: ITEM NAME/DESCRIPTION QTY 1 1/2 X 3-1/2 IN. BOLT ........................................................................................................ 6 i/2 X 3-1/4 IN. BOLT ........................................................................................................ 2. 3 1/2 X 3 IN. BOLT ..................................................................................................
ページ11に含まれる内容の要旨
893102 PROSYSTEM ASSEMBLY PARTS LIST SORT AND COUNT ALL PARTS BEFORE BEGINNING ASSF_,I~IBLY WELDMENTS/PARTS: ITEM NAME/DESCRIPTION QTY UPRIGHT FRAME W’ELDJ}IENT .................................................................................... 1 2. TOP BO03"I WELD~IENT ................................................................................................ 1 3. CARRIAGE I, VELDMENT ................................................................................................ 1 4. 2 S
ページ12に含まれる内容の要旨
893102 PROSYSTEM ASSEMBLY INSTRUCTIONS Assemble the appropriate END CAY~S to the UPRIGHT FRAME WELDMENT..BENT TUBE. and the LOW ROWATTACHMENT WELDMENT as shown, also attach the 5-1/2 X 2-1/2 IN. NON SKID STRIPS to the LOWROWATTACHMENT as shown. SECURELY assemble the LOW ROWATTACHMENT WELDMENT and the UPRIGHT FRAME ~VELDJ~IENT to the BENT TUBE as shown. LOOSELY assemble the UPRIGHT WELDMENTS to the BENT TUBE as shown. Attach eight (8) 1 IN. SQ. GLIDES to the CARRIAGE WELDMENT as shown in (DETAIL
ページ13に含まれる内容の要旨
893102 PROSYSTEM ASSEMBLY INSTRUCTIONS LOOSELY assemble the LEFT and RIGHT BOOM SUPPORT WELDMENTS to the TOP BOOM WELDMENT as shown. LOOSELY assemble the UPRIGHT WELDMENTS to the LEFT and RIGHT BOOM ’3UPPORT WELDMENTS as shown. SECURELY TIGHTEN ALL LOOSE BOLT CONNECTION MADE TO THIS POINT. Assemble the 4 X 7 IN. ROLLER PADS with MUSHROOM CAPS to the SWIVEL KNEE SUPPORT WELDMENT as shown, also assemble one (1) SPRING PIN ASSEMBLY to the SWIVEL KNEE SUPPORT WELDMENT as shown in (DETAIL D) then SEC
ページ14に含まれる内容の要旨
893102 PROSYSTEM ASSEMBLY INSTRUCTIONS 17. LOW PULLEY CABLE ROUTING ASSEMBL Y (SEE CABLE ROUTING DIAGRA3~I)." ho Route CABLE (657620 i) under and around the PULLEYS at the bottom of the UPRIGHT FRAy’vIE WELDMENT. (NOTE: AFTER CABLE HAS BEEN ROUTED UNDER PULLEY, POSITION CABLE RETAINING CLIP UNDER THE PULLEY AS SHOWN AND TIGHTEN) Route CABLE up and around the bottom PULLEY of the 1-3/4 X 5-1/4 IN. PLATES as shown. and down to, and around the PULLEY under the PULLEY BRACKET WELDMENT. (SEE NOTE ABO
ページ15に含まれる内容の要旨
u[] co m e (- 0 Fq Z 3> c -0 O0 v c FT~ 0
ページ16に含まれる内容の要旨
\1 Z
ページ17に含まれる内容の要旨
x r-~ I :;:u x z zz
ページ18に含まれる内容の要旨
m o o,4 0 ~ / z // / I \ ,J / \ ’J / \ / / / \\ / / / / Z I / \ / / / / /
