ページ1に含まれる内容の要旨
VERTICAL/HORIZONTAL
22 TON LOG SPLITTER
MODEL NO. S402022H0 & S402022K0
Owner’s Manual
ASSEMBLY & OPERATING INSTRUCTIONS
WARNING: All operators must read this manual before operating this log
splitter. Follow the safety instructions in the manual and in decals attached
to the product. Failure to do so could result in serious injury or death.
LS181-877-0411
Rev. 0
ページ2に含まれる内容の要旨
Table of Contents Page(s) Important Safety Information................................................................................................................. 1-6 Intended Use ......................................................................................................................... 1 Personal Protective Equipment ............................................................................................... 1 Safety Decals ................
ページ3に含まれる内容の要旨
WARNING: Read and thoroughly understand all instructions in this manual and on safety decals before assembling or operating this log splitter. Failure to do so may cause serious injury or death. Do not allow anyone to operate this log splitter who has not read this manual. As with all power equipment, a log splitter can be dangerous if assembled or used improperly. Do not operate this log splitter if you have any questions concerning safe operation. To get answers to any questions, call our
ページ4に含まれる内容の要旨
PART NUMBER: S52062400 LOCA TION: HYDRAULIC T ANK LOWER T ANK, RIGHT CORNER PART NUMBER: S52062200 LOCA TION: T OP OF CYLINDER PART NUMBER: S52062100 LOCA TION: T OP OF HYDRAULIC PART NUMBER: CYLINDER LOCA TION: OUTSIDE OF BOTH Page 2 STRIPPER PLATES
ページ5に含まれる内容の要旨
GENERAL SAFETY ALWAYS keep the operator’s manual nearby for reference. Reread the manual periodically. ALWAYS establish a safety zone restricting bystanders to a 10 foot radius around the log splitter when log splitter is in operation. ALWAYS ensure that all operators are properly trained or have read and understood the operator’s manual. ALWAYS operate the log splitter with a clear mind, free of the influence of alcohol, drugs or medication. ALWAYS wear close fitted clothing, free from lanyards
ページ6に含まれる内容の要旨
OPERATION OF THE LOG SPLITTER ONLY operate the log splitter from the operator zone as shown in the diagram. The operator has the safest and most efficient access to the control valve and the beam in this location. Operating the log splitter in another location can result in serious injury or death. TOP VIEW OPERATOR ZONE ALWAYS block the wheels to prevent movement of the log splitter while in operation. KNOW how to stop the log splitter and disengage the controls before operating it. NEV
ページ7に含まれる内容の要旨
NEVER perform any service or repair on your log splitter without first removing the spark plug wire. ALWAYS perform all recommended maintenance procedures before using your log splitter. ALWAYS check the level of hydraulic oil and engine oil before operation. ALWAYS periodically check that all nuts, bolts, screws, hydraulic fittings and hose clamps are tight. ALWAYS replace all damaged or worn parts immediately. ALWAYS be sure that all replacement parts meet manufacturer ’ s specifications.
ページ8に含まれる内容の要旨
IMPORTANT NOTE – (spark arrester): As a precautionary measure against possible flying sparks, always take a Class B fire extinguisher with you when operating this log splitter in dry areas. This log splitter is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is
ページ9に含まれる内容の要旨
ASSEMBLY INSTRUCTIONS ITEM NO. DECSRIPTION QTY. 1 Road-Speed Tire and Wheel 2 2 Hardware Kit (not shown) 1 3 Tongue Assembly 1 4 Tank Assembly 1 5 Beam Lock Assembly 1 6 Beam Assembly 1 NOTE: This log splitter was partially assembled at the factory. Refer to the drawing and parts list should it become necessary to disassemble the unit for repair or replacement of parts. STEP 1: Remove all the components from the shipping container.Inspect each piece for shipping d
ページ10に含まれる内容の要旨
STEP 3: Attach the tongue assembly (5) to the tank assembly (1) using two 1/2” NC x 4-1/2” hex cap bolts (2), two 1/2” lock washers (3) and two and two 1/2” hex nuts (4). T ighten. 5 ITEM NO. DESCRIPTION QTY. 1 Tank Assembly 1 2 1/2” NC x 4-1/2 Hex Bolt 2 3 1/2” Lock Washer 2 4 1/2” NC Hex Nut 2 5 Tongue Assembly 1 STEP 4: Stand the beam (1) up on end. Two people may be needed for this step to ensure sa
ページ11に含まれる内容の要旨
STEP 5: Connect the end of the 1/2” ID x 38” hydraulic pressure hose (1) coming from the fitting on the pump to the fitting on the valve. See illustrations below . STEP 6: Slide one hose clamp on the end of the 1/2” x 56” hydraulic return hose (2 ) that comes from the fitting on the filter . Then connect the hose to the fitting on the valve.T ighten hose clamps. See illustrations below . Area of Detail ITEM NO. DESCRPTION QTY. 1 1/2” X 38” Pressure Ho
ページ12に含まれる内容の要旨
REPLACEMENT PARTS TANK/ENGINE ASSEMBLY BREAKDOWN ITEM NO. PART NO. DESCRIPTION QTY. 1 O/L 5/16” Flat Washer 8 2 O/L 5/16”-18UNC Nylock Nut 4 3 O/L 5/16” x 1-1/2” GR 5 Bolt 4 4 S40118800 Tank 1 5 S390604B0 Filter Base 1 5A S390601A0 Filter Element 1 6 S39034900 3/4” Hex Nipple 1 7 S39038300 Straight Fitting, 3/4” NPT to 1 3/4” ID Tube 8 S39032000 3/4” NPT x 3/4” Tube 1 9 S39037100 Pump/Honda Engine Assy. or 1 S39074000 Pump/Kohler Engine Assy. 10 S071022W
ページ13に含まれる内容の要旨
ENGINE/PUMP ASSEMBLY BREAKDOWN ITEM NO. PART NO. DESCRIPTION QTY. 1 O/L 5/16”-18 UNC Nylock Nut 4 2 O/L 5/16” Regular Lock WAsher 4 3 O/L 5/16” x 1-1/4”GR5 Hex Bolt 4 4 O/L 5/16” x 1 UNF GR5 Hex Bolt 4 5 S39053100 Honda GC190 Engine or 1 S39055000 Kohler SH265 Engine 6 S40034800 3/16” x 1” Square Key 1 7 S40081200 Pump Mount 1 8 S400835L0 Jaw Coupler 3/4” Bore 1 9 S400833L0 Jaw Coupler 1/2” Bore 1 10 S400834L0 Rubber Coupler Spider 1 1
ページ14に含まれる内容の要旨
TONGUE ASSEMBLY BREAKDOWN ITEM NO. PART NO. DESCRIPTION QTY. 1 O/L M10 x 1.5 x 120mm GR5 Bolt 2 2 O/L M10 x 1.5 Nylock Nut 2 3 O/L M10 Flat W asher 6 4 S40032300 Chain w/Hook 2 5 S40034600 Hitch Ball Assembly 1 6 S40127400 Ground Stand 1 7 S401215A0 Tongue 1 8 S9114-1 Retaining Ring 1 9 S9132-1 Washer 1 O/L- Obtain locally. Common fasteners available through hardware and farm stores. Page 12
ページ15に含まれる内容の要旨
OPERATING INSTRUCTIONS WARNING: Read and thoroughly understand all instructions and safety information before operating this log splitter. Failure to do so may cause serious injury or death. Do not allow anyone to operate this log splitter who has not read this manual. As with all power equipment, a log splitter can be dan- gerous if assembled or used improperly. Do not operate this log splitter if you have doubts or ques- tions concerning safe operation. Call our customer service department a
ページ16に含まれる内容の要旨
To Stop the Engine 1) Move the throttle lever to the SLOW position. 2) Move the throttle lever to the STOP position. 3) Turn the fuel valve to the OFF position. ENGINE OIL RECOMMENDATIONS (Kohler SH265) For temperatures above 32 degrees F use an 10W-30 oil. Using mutigrade oil may increase oil consumption. Using SAE 30W oil below 40 degrees F will resuilt in hard starting and possible engine bore damage.For temperatures below 32 degrees F use an SAE 5W-20 or SAE 5W-30 oil. Oil capac- ity is ab
ページ17に含まれる内容の要旨
CAUTION: TURN FUEL SHUT OFF VALVE TO THE “OFF” POSITION PRIOR TO TOWING.FAILURE TO DO SO MAY RESULT IN FLOODING THE ENGINE. NOTE: The engine maximum governed speed is preset at the factory at 3600 RPM no load speed. When splitting wood the throttle should be set at the maximum speed to develop the horsepower required for the pump. OPERATION WARNING: See safety information related to operation of the log splitter in the safety section of this manual. Make sure that you have the
ページ18に含まれる内容の要旨
Log Splitter Accessories Make your log splitter more productive with these optional accessories! S40200600 Log Catcher Bolts onto side of the log splitter beam in minutes. Saves time. Saves your back. Holds the split log off to the side until you are ready to quarter it. No more bending over to pick up half split logs. S40201200 Four W ay W edge Double your productivity with this handy attachment. Just slip the 4-way wedge over the standard wedge. Then secure with cable and
ページ19に含まれる内容の要旨
IMPORTANT NOTICE W e, the manufacturer , reserve the right to change the product and/or specifications in this manual without notification. The manual is for information usage only and the pictures and drawings depicted herein are for reference only. NOTES Warranty Repair and Service Do not return this product to the store for warranty issues or repair. Call 1-800-525-8322 for the location of the nearest service center. Record the information below for future reference. Model No. _____________
ページ20に含まれる内容の要旨
SPECIFICATIONS Engine Honda GC190 or Kohler SH265 Pump Two-Stage, 11 gpm Cylinder 4 in. Diameter x 24 in. Stroke Valve Auto-Return Maximum Splitting Force 22 Tons* Maximum Log Length 26 in. Cycle T ime 13 Seconds* Wheels 4.80 x 8 in. Road -Speed Wedge 8 in. High with Spreader WIngs Beam 6 in. x 9 in. with Built-In Log Cradle Hydraulic Capacity 6.5 Gal. Maximum Filter Spin-On Replaceable Height 43 in. in Horizontal Position Length 95 in. Width 49 in. Weight 595 lbs. *Tonnage and cycle times may
