ページ1に含まれる内容の要旨
ACE DRIVER
DELUXE
Operators Manual
IT IS THE RESPONSIBILITY OF THE OPERATOR TO MAINTAIN CUSTOMER SAFETY
AT ALL TIMES, AND IT IS IMPERATIVE THAT THE DETAILS SET OUT IN THIS
MANUAL ARE FOLLOWED PRECISELY.
Part No. 90500019
ページ2に含まれる内容の要旨
SAFETY WARNING In Order to Use This Machine Safely In order to use this machine safely, be sure to read this Operators Manual and the Installation and Commissioning manual carefully before installation and use of the machine. Whenever the owner of this machine entrusts disassembly, installation, adjustment, routine maintenance or trouble shooting to another person, the owner should ensure that they read the appropriate precautions and relevant sections of this manual before starting work. In ord
ページ3に含まれる内容の要旨
© 1994 Ltd - all rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of phonographic recording, nor may it be stored in a retrieval system, transmitted or otherwise copied for public or private use, without permission from namco Ltd. While the information contained in this manual is given in good faith and was accurate at the time of publication, BRENT LEISURE LIMITED reserve the right to make changes and alteration
ページ4に含まれる内容の要旨
Contents 1. HOW TO PLAY ............................................................................................................... 1 2. SPECIFICATIONS .......................................................................................................... 2 3. PRECAUTIONS .............................................................................................................. 4 3-1. Notes on Operation ...................................................................................
ページ5に含まれる内容の要旨
6-4. Removing the Monitor....................................................................................... 27 6-5. Steering and Shift Lever ................................................................................... 29 6-5-1. Replacing the Steering Wheel..............................................................29 6-5-2. Shift Assembly Maintenance ................................................................ 29 6-5-3. Replacing the Steering Drive PCB .........................
ページ6に含まれる内容の要旨
1. HOW TO PLAY • This machine is a multi-player racing game that allows several people to play at the same time, up to a maximum number of eight. � When two or three players are competing against each other, the computer car is included and competition is between four cars. When four or more players compete against each other, competition is amongst those players only. When only one player is playing, he/she competes against the computer cars. [Game Summary] � The object of the game is to comple
ページ7に含まれる内容の要旨
2. SPECIFICATIONS POWER SUPPLY :- 220/240volts AC POWER CONSUMPTION:- 720W MONITOR :- Hantarex 28" Polo Colour Monitor with auto degauss. DIMENSIONS :- - Assembled: 2,370mm(w) x 2,180mm(d) x 2,200mm(h) - Separated: Seat Assy 1,070mm(w) x 2,030mm(d) x 1,640mm(h) Tower Assy 2,100mm(w) x 850mm(d) x 1,760mm(h) Header Assy 1,380mm(w) x 842mm(d) x 325mm(h) Sign Boards 440mm(w) x 170mm(d) x 490mm(h) WEIGHT:- - Assembled: 1,112kg - Separated: Seat Assy 360kg (x2) Tower Assy 348kg Header Assy 32kg Sign
ページ8に含まれる内容の要旨
ACCESSORIES :- Keys: (Cash Door)..................................................... 2 (Coin Door)...................................................... 2 (Back Door) ..................................................... 2ea IEC Mains Lead .................................................................. 1 Operators Manual...............................................................1 Installation & Commissioning Manual ................................ 1 Monitor Manual .......................
ページ9に含まれる内容の要旨
3. PRECAUTIONS Be sure to read this section carefully 3-1. Notes on Operation NOTE: Only operate this machine after checking that it has been installed correctly and in accordance with the Installation and Commissioning manual. NOTE: The supplied guard fence is to ensure customers do not get too close to the machine or get injured. Make sure that the fence is fitted to the machine correctly and the rubber safety mats are in place. NOTE: Parts of this machine move during game play, so there are p
ページ10に含まれる内容の要旨
3-2 Notes on Installation 1. This machine is designed for indoor use only. Do not install the machine in the following places: Page 5
ページ11に含まれる内容の要旨
2. If this machine is installed next to walls or other machines, ensure there is plenty of space between them NOTE: So that customers are not crushed or injured while the machine is moving, ensure that it is separated from walls or other machines by at least 30cm. NOTE: In order that the PCB rack or power supply can be removed for service, make sure that the rear of the machine is separated from a wall or other machine by a distance of at least 50cm or more. 3-3. Notes on Moving and Shipping NO
ページ12に含まれる内容の要旨
3-4 Notes on Handling DANGER The Mains voltage to this machine should be within the range of 220 to 240v AC and the transformer input matched accordingly. DANGER Be sure that the power is turned OFF when replacing parts and connecting/disconnecting connectors. DANGER to prevent possible electric shocks due to failure, this machine MUST be fitted with a securely connected earthed plug. DANGER The monitor and power supply contain areas of very high voltage. Be extremely careful when inspecting or
ページ13に含まれる内容の要旨
4. MAJOR COMPONENTS Page 8
ページ14に含まれる内容の要旨
5 ADJUSTMENTS 5-1 Turning on the Power After the machine has been installed, turn ON the power. The Power switch is located on the rear of the upper tower section. (See section 4 "Major Components" (page 8).) 5-2 Adjustment Switches The adjustment switches are located inside the coin door. 1. Service Switch Press this switch to obtain game credits without incrementing the play meters. 2. Test Switch Slide this switch "ON" to enter test mode. Test mode allows game testing and the changing of game
ページ15に含まれる内容の要旨
5-3 Test Mode 1. Open the coin door and slide the test switch "ON". The "Menu Screen" will be displayed on the monitor. 2. Select the test required by moving the shift lever up or down. The colour of the selected test will change. 3. Enter the selected test by stepping on the accelerator. Select "EXIT" to return to the "Menu Screen" (step on the accelerator when using the monitor test screen). 4. After testing is completed, ensure that the test switch is returned to the "OFF" position to return
ページ16に含まれる内容の要旨
5-3-1 Coin Options a. Select item (1) COIN OPTIONS [DEFAULT IN GREEN] "COIN OPTIONS" on the menu screen, GAME COST to set the game cost 1 COIN 1 CREDIT ........... (a) and related settings. COIN1 MECH VALUE b. Use the shift lever to 1 COIN COUNT AS 1 COIN ........... (b) select the required item then step on COIN MECH 2 VALUE the accelerator. 1 COIN COUNT AS 1 COIN ........... (c) c. Use the shift lever to BONUS FOR QUANTITY BUY IN change the settings NONE ........... (d) then step on the accele
ページ17に含まれる内容の要旨
5-3-2 Game Options a. Select item (2) "GAME OPTIONS" on the GAME OPTIONS [DEFAULT IN GREEN] menu screen to set the game options. PCB ID NUMBER ................. (a) b. Use the shift lever to TEAM COLOUR BLUE3 ................. (b) select the required item RACE CLASS BEG EXP PRO ................. (c) then step on the accelerator. DIFFICULTY B B B ................. (d) c. Use the shift lever to LAPS [LINK] 3 3 4 ................. (e) change the settings then step on the LAPS [SOLO] 3 3 4 ........
ページ18に含まれる内容の要旨
IN TEM DT ESCRIPTIO FACTORY SE (a) PCB Number The PCB number should be set so that none of the linked positions have the same number (D b) Team Colour R6 E 25 or 2 B4 LUE 3 or Y8 ELLOW 17 or 1 G2 REEN 11 or 1 * When more than three sets (6 seats) are linked, different race numbers should be used for the same team colours. (c) Race BEG() d) Game difficulty level (time) A (long) to D (short B Class 3 (6 e) Number of laps (linked game) 3 to (6 f) Number of laps (solo play) 3 to 3 EXP() d) Game diff
ページ19に含まれる内容の要旨
5-3-3 I/O Test 1. Select item (3) "I/O TEST" on the menu screen. 2. Use the shift lever to select the required item then step on the accelerator. I/O TEST DIP 2 12345678 ........... (a) Option Switch (CPU-PCB Sw2) 3 12345678 ........... (b) Option Switch (CPU-PCB Sw1) LINK ON 2 COUNT 0 ........... (c) Link Check SWITCH ........... (d) Switch Test MOTOR ........... (e) Motor Test LAMP ........... (f) Lamp Test LED ........... (g) LED Test EXIT GAS: ENTER SHIFT: CHOOSE (a) Displays the state of th
ページ20に含まれる内容の要旨
5-3-4 Switch Test The following screen is displayed when "SWITCH" is selected on the I/O screen. I/O TEST DIP 2 12345678 3 12345678 LINK ON 2 COUNT 0 SWITCH (a) Accelerator ................ GAS: *0000 COIN 1: OFF .............. (e) Coin 1 switch (b) Brake ................ BRAKE *0000 COIN 2: OFF .............. (f) Coin 2 switch (c) Steering ................ STEER *0000 SERVICE: OFF ..............(g) Service switch (d) Shift ................ SHIFT CENTRE VIEW: OFF .............. (h) View change
