ページ1に含まれる内容の要旨
CR9922
3 Band Dual Alarm
Clock Radio
Please read this manual before use
ROBERTS
Sound for Generations
ページ2に含まれる内容の要旨
123 4 Controls 14 13 12 11 10 9 8 7 6 5 1. Clock display 5. Fast forward button 9. Slow reverse button 13. Alarm 1 indicator 6. Time set button 10. Snooze button 2. Alarm 2 indicator 14. PM indicator 3. Headphone socket (on rear) 7. Alarm set/Off button 11. Alarm type indicators 4. LED dial pointer 8. Sleep button 12. Auto dimmer 1
ページ3に含まれる内容の要旨
Controls 15 16 17 18 19 20 21 15. Display brightness switch 18. Volume control 19. Waveband selector 16. Alarm selector switch 17. Function switch 20. Tuning control 21. Battery compartment (on underside) If you need any further advice, please call our Technical Helpline on :- 2 020 8758 0338 (Mon-Fri)
ページ4に含まれる内容の要旨
Switching on and setting the time ON Before using your clock radio you must first set the correct time. 1. Place the unit on a flat surface. Plug the mains lead into a wall socket and switch on. 2. The clock display will flash 12:00. 3. Press and hold down the Time Set button. 4. Whilst holding down the Time Set button press the fast forward (Fast), or slow reverse (Slow) buttons to set the time. Release the buttons when the correct time is reached. The clock uses a 12 hour display with a PM ind
ページ5に含まれる内容の要旨
Listening to the Radio 1. Switch on the radio by sliding the Function switch to the 'On' position. The LED dial pointer will light up indicating that the radio is switched on. 2. Select the required waveband using the Waveband selector switch. 3. Tune in to the desired station by rotating the Tuning control. The station frequency is indicated by the LED dial pointer. The Wire aerial located on the rear of your clock radio is for FM reception. The wire should be fully extended and positioned for
ページ6に含まれる内容の要旨
Setting alarm times The alarms can be set to wake you by either buzzer or the radio alarms. Your alarm clock radio has 2 separate alarms which can be set to activate at different times. Setting alarm 1 1. Slide the Alarm function switch to the ' ' position. 1 2. Press and hold down the Alarm set button. 3. Whilst holding down the Alarm Set button press the fast forward (Fast), or slow reverse (Slow) buttons to set the required alarm time. Release the buttons when the correct alarm time is reac
ページ7に含まれる内容の要旨
3. Whilst holding down the Alarm Set button press the fast forward (Fast) or slow reverse (Slow) buttons to set the required alarm time. Release the buttons when the correct alarm time is reached. The clock uses a 12 hour display with a PM indicator. Ensure that the correct 12 hour cycle is selected. Checking the Alarm Times 1. To check alarm 1 time, set the Alarm function switch to the ' ' 1 position. 2. Press the Alarm Set button to display the alarm 1 time. 3. To check alarm 2 time, set the
ページ8に含まれる内容の要旨
Setting the alarms to wake to buzzer 1. Set the alarm time as previously described. Set the Function switch to the 'Buzz' position. Set the Alarm selector switch to the ' ', ' ' or ' ' position. The corresponding Alarm 1 2 1+2 indicators will light. 2. The buzzer alarm will sound every day at the preset time for 59 minutes. To turn off the alarm until the next day press the Alarm/ Off button. To turn off the alarms permanently set the Function switch to the 'Off' position. Note: If an alarm t
ページ9に含まれる内容の要旨
Snooze control The buzzer or radio alarm can be silenced for 7 minutes by pressing the Snooze button. This sequence can be repeated whilst the alarm is sounding. Sleep timer The radio can be set to switch off after a preset time has elapsed. Press and hold down the Sleep button until the desired time is reached (maximum 59 minutes in 1 minute steps). The radio will switch off after the sleep time has elapsed. To cancel the sleep function before the preset time has expired, press the Alarm/Off bu
ページ10に含まれる内容の要旨
General Fuse Do not allow this unit to be exposed to water or steam. It is recommended This apparatus must be protected by a 3A fuse (BS1362) in a 13A plug that the FM band be used wherever possible as better results in terms (BS1363). If another type of plug is used a 5A fuse should be fitted in the of quality and freedom from interference will usually be obtained than plug, adaptor or distribution board. on the MW or LW bands. IF IN DOUBT - CONSULT A QUALIFIED ELECTRICIAN. Mains supply Back-up
ページ11に含まれる内容の要旨
Specifications Circuit Features Power Requirements Loudspeaker 8 ohms Mains AC 230 volts, 50Hz only Output power 350mW Back-up Battery IEC size 6LR61 (6F22, PP3) Aerial System FM Wire Aerial Frequency Coverage FM 87.5 - 108MHz MW Built-in Ferrite aerial MW 525 - 1610kHz LW 150 - 260kHz LW Built-in Ferrite aerial ROBERTS RADIO LIMITED PO BOX 130 MEXBOROUGH SOUTH YORKSHIRE S64 8YT The Company reserves the right to amend the specification without notice. If you need any further advice, please call
ページ12に含まれる内容の要旨
Guarantee This radio is guaranteed for twelve months from the date of delivery to the original owner against failure due to faulty workmanship or component breakdown, subject to the procedure stated below. Should any component or part fail during this guarantee period it will be repaired or replaced free of charge. The guarantee does not cover: 1. Damage resulting from incorrect use. 2. Consequential damage. 3. Product with removed or defaced serial numbers. Procedure: Any claim under this guara
