Miller Electric 500SSXの取扱説明書

ページ1に含まれる内容の要旨

1994 Form: OM-168 256
Apri
Miller
Effective With Serial No. KE600689
OWNERS
MANUAL
Gold Starfi
500SSX
CC/DC Power Source
Welding
ForSMAW and GTAW
Welding
510 41 Volts At 35%
Amperes, DC, Duty Cycle

50/60 Hz Power
Requires Three-Phase, Input

Protection
Overheating

Arc Control
(Dig)
Read and follow these instructions and all Give this manual to the
operator.
blocks
safety carefully.
Have trained and

only qualified persons
For
this call distributor
install, or service unit. hel

ページ2に含まれる内容の要旨

ページ3に含まれる内容の要旨

I ~-1S 7S~> ~. J MILLERS TRUE BLUETM LIMITED WARRANTY Effective ,Janu 1, 1992 ary with a serial number of KC or (Equipment preface newer) This limited all previous MtLLER warranties and is evr:tusive with no other or warranties espreased or imptied. warranty supersedes guarantees * LtMITEDWARRANTY to the terms and coeditione betow, MtLLER Electric Remote Controls Subject to its Co Appleton, Wisconsin, warrants original retail purchaser that new Mtg. . Kits Accessory MILLER sotd after t

ページ4に含まれる内容の要旨

ページ5に含まれる内容の要旨

WELDING SAFETY PRECAUTIONS ARC ARC WELDING be a WARNING can hazardous. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHILDREN AWAY. PACEMAKER WEARERS KEEP AWAY UNTIL CONSULTING YOUR DOCTOR. In in as most to certain hazards occurs. is safe when taken. The welding, jobs, exposure Welding precautions are information below is a of the more information that will be found in the safety given only summary complete safety Standards listed the next Read on and follow all Standar

ページ6に含まれる内容の要旨

ページ7に含まれる内容の要旨

J 3. from CYLINDERS if Keep cylinders or other electrical can away any welding explode damaged. circuits. contain under Shieldin~ gas cylinders gas high 4. Never allow a electrode to touch welding any cylinder. If Since ~ a cylinder can explode. pressure. damaged, 5. Use correct only shielding cylinders, hoses, and ~ of gas regulators, ~J are the gas cylinders normally part welding for the to treat them specific maintain them and . process~ be sure fittings designed application; carefully, in

ページ8に含まれる内容の要旨

ページ9に含まれる内容の要旨

PRECAUTIONS SECURITE DE EN A SOUDAGE LARC MISE EN GARDE A LE SOUDAGE LARC est dangereux. AINSI QUE LES CONTRE LES PROTEGEZ-VOUS, AUTRES, BLESSURESGRAVES POSSIBLESOU LA MORT. NE LAISSEZ PAS LES ENFANTS NI LESPORTEURSDESTIMULATEURCARDIAQUE MOINS CONSULTE SAPPROCHER, QUILSNAIENT UN (A MEDECIN). Le Ia des activitØs a certains soudage, comme plupart industrielles, Le nest des expose risques. soudage pas dangereux lorsquon prend Les de sØcuritØ suivantes ne font rØsumer information contenue dans l

ページ10に含まれる内容の要旨

ページ11に含まれる内容の要旨

ETINCELLES LES ET LES metal. En Ia soudure refroidissant, du laitier. peut projeter 1. Portez un Øcran facial des lunettes a PROJECTIONS BRULANTES ou coques approuvØes. peuvent Des Øcrans latØraux sont recommandØs. des blessures. causer 2. Portez des vŒtements de individuelle protection appropriØs. Le et le des Øclats de piquage meulage produisent 4. Les BOUTEILLES tout contact entre une bouteille et une electrode. EmpŒchez endommagees peuvent 5. Nutilisez des bouteillesde des que gaz protecteu

ページ12に含まれる内容の要旨

ページ13に含まれる内容の要旨

EMF INFORMATION Considerations About And The Effects OfLow Electric And Frequency Welding NOTE ~ Fields Magnetic -~ Section in The is a from the General Conclusions To reduce fields the use the following quotation magnetic workplace, following of the U.S. Office of Congress, TechnologyAssessment, Biological procedures: Effects of Power Electric & Fields Frequ9ncy Magnetic 1. cables close or them. Keep together by twisting taping OTA-BP-E-53 DC: U.S. Paper, Background (Washington, 2. cables to

ページ14に含まれる内容の要旨

ページ15に含まれる内容の要旨

ページ16に含まれる内容の要旨

ページ17に含まれる内容の要旨

- SECTION 1 INFORMATION SAFE~TY modl.1 2/93 Read all this manual. safety messages throughout all to avoid Obey safety messages injury. of Learn thi? WARNING and CAUTION. meaning 1 Alert Safety Symbol 2 Word Signal 1 2 2 WARNING death means possible serious or can injury happen. iIIi1~I : ! CA~ CAUTION means minor possible ~ ELECTRIC SHOCK can w~OVING PARTS can or can Injure. injury equipment damage kIII.~ S happen. Do not touch live electrical from parts. ~fl Keep away moving parts.

ページ18に含まれる内容の要旨

ページ19に含まれる内容の要旨

2-1. Curves Volt-Ampere The show the volt-ampere curves minimum and maximum voltage and output capabilities amperage of the welding source. power Curves of other fall be settings tween the curves shown. A~. Low B. Range High Range 70 70 60 60 50 50 40 40 0 0 > > 30 30 C.) C.) 20 20 10 10 0 0 0 50 100 150 2D0 250 300 350 400 450 500 650 600 0 100 200 300 400 600 600 700 800 900 DC AMPERES DC AMPERES ssbl .110/91 SB-084 850-A / SB-084 845-A 2-1. Curves Figure Volt-Ampere 2-2. Duty Cycle L ~AUTI

ページ20に含まれる内容の要旨