ページ1に含まれる内容の要旨
Demolition Hammer
MODEL HM1500B
002883
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
ページ2に含まれる内容の要旨
SPECIFICATIONS Model HM1500B Blows per minute 1,300 Overall length 807 mm (31-3/4”) Net weight 19 kg (42 lbs) • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area 4. Double insulated
ページ3に含まれる内容の要旨
6. Do not expose power tools to rain or wet Tool Use and Care conditions. Water entering a power tool will 15. Use clamps or other practical way to increase the risk of electric shock. secure and support the workpiece to a 7. Do not abuse the cord. Never use the cord stable platform. Holding the work by hand or to carry the tools or pull the plug from an against your body is unstable and may lead outlet. Keep cord away from heat, oil, to loss of control. sharp edges or moving parts. Replace 16.
ページ4に含まれる内容の要旨
24. When servicing a tool, use only identical Use of unauthorized parts or failure to follow replacement parts. Follow instructions in Maintenance instructions may create a risk of the Maintenance section of this manual. electric shock or injury. USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in l
ページ5に含まれる内容の要旨
tion. Without proper warm-up, hammering 11. Do not point the tool at any one in the area operation is difficult. when operating. The bit could fly out and injure someone seriously. 7. Always be sure you have a firm footing. Be sure no one is below when using the 12. Do not touch the bit or parts close to the tool in high locations. bit immediately after operation; they may be extremely hot and could burn your 8. Hold the tool firmly with both hands. skin. 9. Keep hands away from moving parts. 13
ページ6に含まれる内容の要旨
FUNCTIONAL CAUTION: DESCRIPTION Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 002891 Switch action CAUTION: 1 Before plugging in the tool, always check to see that the 2 switch trigger actuates properly and returns to the “OFF” position when released. Switch can be locked in “ON” position for ease of operator comfort during extended use. Apply caution 1. Lock button when locking tool in “ON” position and maintain firm 2. Swit
ページ7に含まれる内容の要旨
002928 Installing or removing the bit 1 This tool accepts bits either with or without a collar on its shank. To install the bit, follow either procedure (1) or (2) described 2 below. (1) For bits with a collar 002934 1. Bit with collar 1 2. Bit without coller 2 3 4 5 Fig.(1) 1. Bit 2. Tool retainer 3. Tool holder 4. When the bit is inserted 5. When the bit is retained Pivot the tool retainer back and slightly downward. Insert the bit into the tool holder as far as it will go. To securely retain
ページ8に含まれる内容の要旨
CAUTION: Always assure that the bit is securely retained by attempting to pull the bit out of the tool holder after completing the above procedure. The bit without a collar cannot be retained by the method shown in Fig.(1). To remove the bit, follow the installation procedure in reverse. OPERATION Chipping/Scaling/Demolition Hold the tool firmly with both hands. Turn the tool on and apply slight pressure on the tool so that the tool will not bounce around, uncontrolled. Pressing very hard on
ページ9に含まれる内容の要旨
002958 Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure 1 the brush holder caps. 2 1. Screwdriver 2. Brush holder cap 002972 Lubrication 1 This tool requires no hourly or daily lubrication because it has a grease-packed lubrication system. It should be relubri- cated after every 6 months of operation. Send the complete tool to Makita Authorized or Factory Service Center for this lubrication service. However, if circumstances requ
ページ10に含まれる内容の要旨
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita service center. Bull point Cold chisel Scaling chisel Clay spade Rammer Safety goggles Hammer grease Hex wrench
ページ11に含まれる内容の要旨
Memo 11
ページ12に含まれる内容の要旨
Memo 12
ページ13に含まれる内容の要旨
First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold 13 Cut
ページ14に含まれる内容の要旨
MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: 3. How did you learn about this product: Home Center Other ( ) Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( ) 2. Use of the product is intended for: 4. Most favored points are: Construction Trade Design Repair Se
ページ15に含まれる内容の要旨
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ARIZONA FLORIDA MISSOURI PENNSYLVANIA 3707 E. Broadway Rd., Ste. 6 750 East Sample Road 9876 Watson Road 1704 Babcock Blvd. Phoenix, AZ 85040 Pompano Beach, FL 33064 St. Louis, MO 63126-2221 Pittsburgh, PA 15209 (602) 437-2850 (954) 781-6333 (314) 909-9889 (412) 822-7370 CALIFORNIA GEORGIA NEBRASKA PUERTO RICO 41850 Christy St. 4680 River Green Parkway NW 4129 S. 84th St. 200 Guayama St. Fremont, CA 94538-5107 Duluth,
ページ16に含まれる内容の要旨
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of
