Makita HM1202の取扱説明書

デバイスMakita HM1202の取扱説明書

デバイス: Makita HM1202
カテゴリ: エアハンマー
メーカー: Makita
サイズ: 0.15 MB
追加した日付: 7/8/2014
ページ数: 16
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスMakita HM1202の取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Makita HM1202に関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Makita HM1202をこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Makita HM1202のフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Makita HM1202の説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Makita HM1202 取扱説明書 - Online PDF
Advertisement
« Page 1 of 16 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Makita HM1202を全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Makita HM1202の内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

Demolition Hammer
MODEL HM1202
MODEL HM1202C
002877
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com

ページ2に含まれる内容の要旨

SPECIFICATIONS Model HM1202 HM1202C Blows per minute 1,900 950 - 1,900 Overall length 578 mm (22-3/4”) Net weight 9.3 kg (20.5 lbs) • Manufacturer reserves the right to change specifications without notice.  Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Ar

ページ3に含まれる内容の要旨

6. Do not expose power tools to rain or wet Tool Use and Care conditions. Water entering a power tool will 15. Use clamps or other practical way to increase the risk of electric shock. secure and support the workpiece to a 7. Do not abuse the cord. Never use the cord stable platform. Holding the work by hand or to carry the tools or pull the plug from an against your body is unstable and may lead outlet. Keep cord away from heat, oil, to loss of control. sharp edges or moving parts. Replace 16.

ページ4に含まれる内容の要旨

24. When servicing a tool, use only identical Use of unauthorized parts or failure to follow replacement parts. Follow instructions in Maintenance instructions may create a risk of the Maintenance section of this manual. electric shock or injury. USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in l

ページ5に含まれる内容の要旨

tion. Without proper warm-up, hammering 11. Do not point the tool at any one in the area operation is difficult. when operating. The bit could fly out and injure someone seriously. 7. Always be sure you have a firm footing. Be sure no one is below when using the 12. Do not touch the bit or parts close to the tool in high locations. bit immediately after operation; they may be extremely hot and could burn your 8. Hold the tool firmly with both hands. skin. 9. Keep hands away from moving parts. 13

ページ6に含まれる内容の要旨

FUNCTIONAL CAUTION: DESCRIPTION  Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 002889 Switch action 1 CAUTION:  Before plugging in the tool, always check to see that the tool is switched off.  Switch can be locked in “ON” position for ease of operator comfort during extended use. Apply caution when locking tool in “ON” position and maintain firm 1. Switch lever grasp on tool. To start the tool, push the switch lever on the left

ページ7に含まれる内容の要旨

Indicator lamp 002899 For HM1202C only The green power-ON indicator lamp lights up when the tool is switched ON. If the indicator lamp is lit but the tool does not 1 start, the carbon brushes may be worn out, or the electric cir- 2 cuit or the motor may be defective. If the indicator lamp does not light up and the tool does not start, the ON/OFF switch or the mains cord may be defective. The red service indicator lamp lights up when the carbon 1. Power-ON indicator lamp(green) brushes are nearly

ページ8に含まれる内容の要旨

002916 Installing or removing the bit Clean the bit shank and apply bit grease before installing the bit. 1 2 1. Bit grease 2. Bit shank 002922 Insert the bit into the tool. Turn the bit and push it in until it engages. 1 If the bit cannot be pushed in, remove the bit. Pull the tool holder cover down a couple of times. Then insert the bit 2 again. Turn the bit and push it in until it engages. After installing, always make sure that the bit is securely held in place by trying to pull it out. 1. B

ページ9に含まれる内容の要旨

OPERATION 002945 Chipping/Scaling/Demolition Hold the tool firmly with both hands. Turn the tool on and apply slight pressure on the tool so that the tool will not bounce around, uncontrolled. Pressing very hard on the tool will not increase the efficiency. MAINTENANCE CAUTION:  Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. 001146 Replacing carbon brushes When the resin insulating tip inside the carbon brush is 2 exposed to co

ページ10に含まれる内容の要旨

002954 Use a screwdriver to remove the brush holder caps. Take out 1 the worn carbon brushes, insert the new ones and secure 2 the brush holder caps. 1. Screwdriver 2. Brush holder cap 002967 Lubrication This tool requires no hourly or daily lubrication because it has a grease-packed lubrication system. It should be relubri- cated after every 6 months of operation. Send the complete 1 tool to Makita Authorized or Factory Service Center for this lubrication service. However, if circumstances requ

ページ11に含まれる内容の要旨

To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES CAUTION:  These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance

ページ12に含まれる内容の要旨

Memo 12

ページ13に含まれる内容の要旨

First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold 13 Cut

ページ14に含まれる内容の要旨

MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: 3. How did you learn about this product: Home Center Other ( ) Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( ) 2. Use of the product is intended for: 4. Most favored points are: Construction Trade Design Repair Se

ページ15に含まれる内容の要旨

FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ALABAMA COLORADO KENTUCKY NEW MEXICO PUERTO RICO 2365 Pelham Parkway 11839 E. 51st Ave. 1215 S. Hurstbourne Parkway 5805 Menaul Blvd. NE 200 Guayama St. Pelham, AL 35124 Denver, CO 80239-2709 Louisville, KY 40222 Albuquerque, NM 87110 Hato Rey, PR 00917 (205) 620-1791 (303) 371-2850 (502) 326-3740 (505) 881-4619 (787) 250-8776 ARIZONA CONNECTICUT LOUSIANA NEW YORK TENNESSEE 3707 E. Broadway Rd., Ste. 6 508 Spring St.

ページ16に含まれる内容の要旨

WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:  lead from lead-based paints,  crystalline silica from bricks and cement and other masonry products, and  arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Makita BHR240ZK 取扱説明書 エアハンマー 10
2 Makita HM1202C 取扱説明書 エアハンマー 80
3 Makita HM1100C 取扱説明書 エアハンマー 19
4 Makita BHR200SH 取扱説明書 エアハンマー 2
5 Makita BHR200 取扱説明書 エアハンマー 10
6 Makita HM0810B 取扱説明書 エアハンマー 3
7 Makita HM1140C 取扱説明書 エアハンマー 1
8 Makita HM1303B 取扱説明書 エアハンマー 17
9 Makita HM0860C 取扱説明書 エアハンマー 43
10 Makita HM1211B 取扱説明書 エアハンマー 6
11 Makita HM1304B 取扱説明書 エアハンマー 37
12 Makita HM1301 取扱説明書 エアハンマー 17
13 Makita HM1242C 取扱説明書 エアハンマー 1
14 Makita HM1500 取扱説明書 エアハンマー 13
15 Makita HM1500B 取扱説明書 エアハンマー 3
16 Black & Decker 5016-09 取扱説明書 エアハンマー 2
17 Black & Decker D25550 取扱説明書 エアハンマー 6
18 Black & Decker 582429-00 取扱説明書 エアハンマー 0
19 Black & Decker 5025 取扱説明書 エアハンマー 2
20 Black & Decker 5014 取扱説明書 エアハンマー 4