ページ1に含まれる内容の要旨
Cordless Finishing Sander
MODEL 90350
MODEL 9035DW
With Fast Charger
INSTRUCTION MANUAL
SPEC I FI CAT IO N S
Pad size No load speed Overall length Net weight
93 mm x 185 mm
6 000 R1min 185 mm 17 114 i 1 3 kg I2 9 lbsi
13 518 x 7 114 i
Battery Cartridge 7000 Model DC7100 Fast charger
Charging Dimensions Net
Voltage
Input Output
time iL x W x Hi weight
A C only DC 145 mm x 80 mm x 61 mm 0 7 kg
72V 1 Hr
50Hz 60Hr 72V (5 314 x 3 118 x 2 318 i 11 5 lbsi
ページ2に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain. Don't use tool in presenc
ページ3に含まれる内容の要旨
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turn- ing it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don't oper- ate tool when you a
ページ4に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS I. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 3. CAUTION - To reduce risk of injury, charge only MAKITA Battery 7000. Other types of batteries may burst causing personal injury and damage. 4. Do not expose charger to rain or snow. 5. Use of an at
ページ5に含まれる内容の要旨
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OFI. 2. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. 3. Do not allow anything to cover or clog the charger vents. 4. Do not short the battery cartridge. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. 5. Do not store the tool and Battery Cartridge in
ページ6に含まれる内容の要旨
Installing or removing battery cartridge 0 Always switch off the tool before insertion or removal of the battery cartridge. 0 To remove the battery cartridge, pull out Battery cartridge the set plate on the tool and grasp both Set plate sides of the cartridge while withdrawing it i from the barrel. 0 To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Snap the set plate back into place. Be sure to close the
ページ7に含まれる内容の要旨
Attaching the abrasive paper *Pull out the clamp lever and insert the paper end. Be careful to maintain the proper paper tension. Align edges of paper with either edge of the pad. (Pre- bending the paper makes attachment easier.) Once the paper is in place, return the clamp lever to its original position. After inserting the paper, make sure the \ Clamper I teeth of the clamper hold it securely. Otherwise the paper will be loose and Clamp lever subject to slippage, resulting in unev
ページ8に含まれる内容の要旨
Switch action Switch button *To start the tool, simply push the switch I I button. Release the switch button to stop. CAUTION : Before inserting the battery cartridge into the tool, be sure the switch actuates pro- perly. Operation *A finishing sander is generally used to re- move only a small amount of material at a time. Since the quality of the surface is more important than the amount of stock removed, do not bear down on the sander. Keep the base flush with the material at
ページ9に含まれる内容の要旨
MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance and adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any o
ページ10に含まれる内容の要旨
Aug 17 84 US CORDLESS FINISHING SANDER Model 90350 Note: The switch and other part configurations may differ from country to country. 10
ページ11に含まれる内容の要旨
MODEL 90350 Sep -19-'84 US 'FoM GD DESCRIPTION ""0" A&, DESCRIPTION 11 Ballancel Housing SeI 1WNh Item 91 21 Name Plate Flat Washer 7 16 1 Ball Bearing 627LLUX 34 Rivet 0 5 41 Bsllery Holder 17 1 Flat Washer 5 10 1 Countersunk Head Screw M4x10 51 Compression Spring 6 61 Switch 19 2 Foot 78 Pan Head Screw M4x22 1With Washer1 20 2 Clamper 81 Push Rod 21 i Base 91 Housing Set [With Item I1 22 4 Pan Head Screw M4x12 [With Washeil 10 1 Motor 24 1 Rubber Pin 4 11 1 Spindle 25 1 Rubber P
ページ12に含まれる内容の要旨
MAKKA LlMmED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one- year,period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or materi
