ページ1に含まれる内容の要旨
Cordless Driver Drill
10 mm (3/8”) MODEL 6170D
10 mm (3/8”) MODEL 6170DW
With Quick Charger
INSTRUCTION MANUAL
SPECIFICATIONS
Capacities
No load speed Dimensions Net
IRPMt IL x W x HI weight
Steel/Wood I Wood screw
10 mm 4.5 mm x 20 mm I 205 mm x 48 mm x 175 mm 0.95 kg
l3/8“) I (3/16” x 3/4”) I - ‘O0 18” x 1-7/8” x 6-7/8”1 I 12.1 Ibs)
I I
Model DC7020 Quick Charger
Input Output Charging time
A.C. only 50 Hz - 60 Hz D.C. 7.2 V. About 3 Hr.
ページ2に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain. Don't use tool in presence of f
ページ3に含まれる内容の要旨
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don’t operate tool when you are t
ページ4に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS I. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (11 battery charger, (2) battery, and (3) product using battery, 3. CAUTION - To reduce risk of injury, charge only MAKITA type recharge- able batteries. Other types of batteries may burst causing personal injury and damage. 4. Do not expose charger to rain or snow
ページ5に含まれる内容の要旨
ADDITIONAL SAFETY RULES FOR CHARGER AND TOOL 1. The Charger and the tool are specifically designed to work together. Do not attempt to charge any other cordless tool with this Charger. Do not attempt to charge the tool with any other charger. 2. Do not charge the tool when temperature is BELOW 10°C (5OOF) or ABOVE 45OC (113OF). 3. Do not use charger in damp or wet locations. 4. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. 5. Do not store the
ページ6に含まれる内容の要旨
Charging Uncao the connector hole. Connect the charging plug to the charging connector, then plug in the charger to the CAUTION : The battery in your new tool is not fully charged. You will need to charge it before use. Do not operate the tool during charging. Overcharging more than 2 days considerably shortens the battery service life. Always unplug the charger after completing the charge. Then cap the charging connector hole. When you charge a new tool or a tool which has not been use
ページ7に含まれる内容の要旨
Switch action Move the reversing switch lever to the "FWD" position for colckwise rotation or the "REV" position for counterclockwise. Tool speed is increased by increasing pres- sure on the tigger. To start the tool, simply pull the trigger. Release the trigger to stop. When the reversing switch lever is in the neutral position, the tool will not start even if you pull the trigger. CAUTION : a Always check the direction of rotation before drilling. *Use the reversing switch lever on
ページ8に含まれる内容の要旨
Drilling operation Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. Drilling in metal To prevent the bit from slipping when starting a hole, make an indentation with a center- punch and hammer at the point to be drilled. Place the point of the bit in the indenta- tion and start drilling. Use a cutting lubricant when drilling metals. The exceptions ar
ページ9に含まれる内容の要旨
Overload protector The overload protector automatically cuts out to break the circuit whenever heavy work is prolonged. Wait 20-30 seconds before resuming operation. MAINTENANCE CAUTION : Always be sure that the tool is switched off before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 9
ページ10に含まれる内容の要旨
ACCESSOR I ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Bits Quick charger DC7020 (A.C. only) I Size I Part NO. ~ Phillips 111R 12-volt Quick charger DC7022 I I 0 Rubber pad assembly *Chuck keys10 Part No. 123001-2 Part No. 763419-1 J
ページ11に含まれる内容の要旨
Mar - 27- 91 US 10 mm (318") CORDLESS DRIVER DRILL Model 6170D Q Note. The switch and other part configurations may differ from country to country
ページ12に含まれる内容の要旨
MODEL 61700 Mar.-27-'91 US 'LiM DESCRIPTION 1 1 1 DrdlChuek SI0 11 Pan Head Screw M5x1E I2 1 2 1 Gear 13 1 3 1 Plans Bearing 5 14 1 4 1 Motmi I5 1 5 1 1 6 1 Holder 6 I6 17 1 7 1 Switch 1 E 1 Housing R IE 1 9 6 Tapping Screw 3x20 19 1 IO 1 can 20 r f MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thorou ly inspected and tested before leaving the factory. It is warranted to be free of defects from workanshlp and materials for the period of ONE YEAR
