ページ1に含まれる内容の要旨
Cordless Drill
MODEL 6040D
MODEL 6040DW
With Quick Charger
INSTRUCTION MANUAL
SPECIFICATIONS
Capacities
No load speed Dimensions Not
IRPM) IL x W x H) weight
SteelIWood Wood screw
10 mm 4.5 mm x 20 mm I 195 mm x 48 mm x 166 mm 0.8 kg
450
1318") I (3116'' x 314") (7-518" x 1-718" x 6-112") I 11.7 Ibs)
Model DC4100A Quick Charger
Input I output I Charging time
~~
A C. only 50 Hz - 60 Hz DC 6 4V 3 Hr
I I
Manufacturer reserves the right to change specifications without notice.
Not
ページ2に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain. Don't use tool in presence
ページ3に含まれる内容の要旨
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don't operate tool when you are t
ページ4に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS I. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and 13) product using battery. 3. CAUTION - To reduce risk of injury, charge only MAKITA type recharge- able batteries. Other types of batteries may burst causing personal injury and damage. 4. Do not expose charger to rain or snow
ページ5に含まれる内容の要旨
ADDITIONAL SAFETY RULES FOR CHARGER AND TOOL 1. The Charger and the tool are specifically designed to work together. Do not attempt to charge any other cordless tool with this Charger. Do not attempt to charge the tool with any other charger. 2. Do not charge the tool when temperature is BELOW 10°C (5OoF) or ABOVE 45OC (113OF). 3. Do not use charger in damp or wet locations. 4. Do not attempt to use a step-up transformer, an engine generator or DC pow- er receptacle. 5. Do not store th
ページ6に含まれる内容の要旨
Charging Connect the charging plug to the charg- ing connector, then plug in the charger to the power receptacle. Charging takes 3 hours. CAUTION: The battery in your new tool is not fully charged. You will need to charge it be- fore use. Do not operate the tool during charging. Overcharging more than 2 days consid- erably shortens the battery service life. Always unplug the charger after completing the charge. When you charge a new tool or a tool which has not been used for a long
ページ7に含まれる内容の要旨
Switch action pull the trigger. To start the tool, simply Release the trigger to stop. Reversing switch action This tool has a reversing switch to change the direction of rotation. Slide the revers- ing switch to the right for clockwise rota- tion or to the left for counterclockwise. Reversing swit CAUTION : 0 Always check the direction of rotation before operation. .Use the reversing switch only when the tool comes to a complete stop. Changing the direction of rotation before the t
ページ8に含まれる内容の要旨
Drilling operation Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. Drilling in metal To prevent the bit from slipping when starting a hole, make an indentation with a centerpunch and hammer at the point to be drilled. Place the point of the bit in the indentation and start drilling. Use a cutting lubricant when drilling metals. The exceptions are ir
ページ9に含まれる内容の要旨
(A.C. only) Size Part No. 784214-0A Phillips #2 Slotted #5F 784010-0A 0 Chuck key S10 Part No 763419-1 784606-0A Square drill bit 0 Tool holster 11 has some bits storage space. only after removing Use holster to carry drill bit. Also keep the reversing switch lever in 0 Rubber pad assembly neutral position when carrying in the holster. Part No. 123001-2 Part No. 823033-3B 8. %% J 0 Foam polishing pad 0 Wool bonnet Part No. 743023-2 Part No 743401-6 9
ページ10に含まれる内容の要旨
Sep.-07-'87 EN CORDLESS DRILL Model 6040D Note: The switch and other part configurations may differ from country to country. 10
ページ11に含まれる内容の要旨
Sep.-07-'87 EN MODEL 6040D 1 1 Pan Head Screw M5x18 11 1 Plane Bearing 4 2 1 DrillChuckS10 12 1 Gear Complete 11 -65 3 Gear 13 1 Plane Bearing 4 1 14 1 Name Plate 4 1 Plane Bearing 5 15 1 Housing Sa1 lWilh Item 61 5 1 Motor 6 1 Housing Set (With Item 151 16 1 Holder 6 17 1 Swnch 7 8 Tapping Screw 3x20 8 1 Switch 18 1 Dade 1 Compression Spring 7 19 1 Ide1 9 10 1 Switch Lever 20 1 Banary 11
ページ12に含まれる内容の要旨
I MAKmA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or mat
