ページ1に含まれる内容の要旨
Fire Detection Control Panel
Series BC216
User Manual Part A
Description
Operating Instructions
Subject to change without notice
© by Labor Strauss Sicherungsanlagenbau Ges.m.b.H. Wien © by MEP - Gefahrenmeldetechnik GmbH. Pockau
ページ2に含まれる内容の要旨
2 User Manual Series BC216 / Part A All rights reserved. Under the copyright laws, no part of this manual or of the software may be multiplied, copied, disseminated, transferred by photo- technical means, reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or in part, without the prior written con- sent of Labor Strauss Sicherungsanlagenbau Ges.m.b.H., Vienna. The information written in this User Manual has been worked out with the highest care. Neither
ページ3に含まれる内容の要旨
User Manual Series BC216 / Part A 3 Contents 1 Introduction ............................................................................ 7 1.1 Symbols and type fonts ................................................................ 8 1.2 Important hints for the user and the installer ............................................ 8 1.2.1 What to do in case of a fire alarm ..................................................... 9 1.2.2 What to do in case of a fault ....................................
ページ4に含まれる内容の要旨
4 User Manual Series BC216 / Part A 4.7.1 Displaying fire alarms - menu point [Alarms] ........................................ 37 4.7.2 Displaying activated actuations - menu point [Activated actuations] .................. 38 4.7.3 Displaying technical messages - menu point [Technical messages] ................... 38 4.7.4 Displaying fault messages - menu point [Faults] ..................................... 38 4.7.5 Displaying disablements - menu point [Disablements] ...........................
ページ5に含まれる内容の要旨
User Manual Series BC216 / Part A 5 6.1.1 Testing of the fire detection control panel and the power supply devices ............. 65 6.1.2 Testing of detectors ................................................................. 65 6.1.3 Testing the alarming devices ........................................................ 66 6.1.4 Testing the fire control systems ..................................................... 66 6.1.5 Testing the transmitting devices ..........................................
ページ6に含まれる内容の要旨
6 User Manual Series BC216 / Part A HB216AE.SAM / 0130 / AN9161202 ZN5002/73/6
ページ7に含まれる内容の要旨
User Manual Series BC216 / Part A Chapter 1 • Introduction 7 1 Introduction Decades of research and development of LST in the field of fire detection control panel technology and the successful cooperation with renowned international test authorities led to the development of the new fire detection control panels BC216-1 and BCnet216 of LST. The fire detection control panel BC216-1 was drafted as a compact control panel for application in fire detection systems of small and medium size.
ページ8に含まれる内容の要旨
8 Chapter 1 Introduction User Manual Series BC216 / Part A This User Manual is not designed as a description of or as an operating instruction for a fire detection system. Therefore, detailed instructions for how to act in case of an alarm or a fault are not given. Indi- vidual differences in the variety of components used and in the setup are so extensive that an efficient general description of the system or of the organization in case of an alarm would not be possible. Due to natio
ページ9に含まれる内容の要旨
User Manual Series BC216 / Part A Chapter 1 Introduction 9 in the expansion of the area surveilled require careful replanning and adaptation of the fire detection system. The fire detection system has to be checked and maintained regularly (at least once a year) by trained and skilled personnel in order to maintain its functions and to avoid false alarms. For planning, installing, modifying, maintaining and servicing your fire detection system, be sure to commission only specialists w
ページ10に含まれる内容の要旨
10 Chapter 1 Introduction User Manual Series BC216 / Part A out the reconditioning. Together with the fire prevention officer you have to determine the additional protective measures that are to be taken until the system is fully operational again. Such measures might include, e.g., special attention by your personnel or fire watches in the area where the fault has occurred. Two special faults are to be emphasized: The light-emitting diode 'POWER' is not illuminated: If nothing else i
ページ11に含まれる内容の要旨
User Manual Series BC216 / Part A Chapter 1 Introduction 11 Further approvals are in preparation. 1.4 Warranty Your fire detection control panel Series BC216 has been manufactured with greatest precision and care. Nevertheless, the possibility of malfunctions cannot be excluded entirely. Please contact the authorized installer of your fire detection system in case of a problem. As long as the warranty is in effect all parts that fail to operate properly because of a demonstrable flaw
ページ12に含まれる内容の要旨
12 Chapter 1 Introduction User Manual Series BC216 / Part A Delay time The delay time consists of reaction- and exploration time. During the reaction period the activation of the transmitting devices for fire alarm messages can be delayed during day-operation of the fire detection system. Exploration time allows the user to find the cause of the alarm and to decide if the fire brigade indeed should be notified. Detection area A particular part of a surveilled area where the fire detec
ページ13に含まれる内容の要旨
User Manual Series BC216 / Part A Chapter 1 Introduction 13 Loop Ring-shaped wiring with bi-directional data-bus to connect intelligent fire detectors (e.g., sensors, detectors) and actuation devices to the fire detection control panel. A wire breakage in the loop leads to a fault display on the control panel but does not affect the functions of the connected de- vices. Isolation elements limit the effect of a short-circuit in the wiring, so that a short-circuit will either have no ef
ページ14に含まれる内容の要旨
14 Chapter 1 Introduction User Manual Series BC216 / Part A ing proper equipment for transmission (e.g., continually monitored telephone cables). The transmit- ting device for fire alarm messages which can also be operated - additionally to the menu control - via the buttons in the field 'TRANSM. DEVICE 1' of the key pad of the control panel is called pri- mary transmitting device. The possibility of alarm delay (also see the terms "Alarm delay proce- dure", "Delay time") is exclusive
ページ15に含まれる内容の要旨
User Manual Series BC216 / Part A Chapter 2 Fire detection control panel Series BC216 15 2 Fire detection control panel Series BC216 The construction of a typical fire detection system, the most important features of the fire detection control panels Series BC216 and the connection of the peripheral components of a fire detection sys- tem to the fire detection control panel are described in this chapter. 2.1 Typical construction of a fire detection system with control panel BC216-1 Fi
ページ16に含まれる内容の要旨
16 Chapter 2 Fire detection control panel Series BC216 User Manual Series BC216 / Part A 2.2 Typical construction of a fire detection system with network control panel BCnet216 Basically the network fire detection control panel BCnet216 does not work differently than described from page 15 in Chapter 2.1: "Typical construction of a fire detection system with control panel BC216-1". The most essential difference to a single control panel is that the network fire detection con- trol pan
ページ17に含まれる内容の要旨
User Manual Series BC216 / Part A Chapter 2 Fire detection control panel Series BC216 17 Basically all fire detectors and other devices that may be connected to a stand-alone control panel of type BC216-1 may also be connected to every single of these BCnet sectional control panels (see from page 15 in Chapter 2.1: "Typical construction of a fire detection system with control panel BC216-1"). The operation of the network control panels by the user is made as usual like with a "one cas
ページ18に含まれる内容の要旨
18 Chapter 2 Fire detection control panel Series BC216 User Manual Series BC216 / Part A In case of an alarm, the user can explore the possible danger prior to the transmission of the fire alarm to the fire brigade by using the alarm delay procedure with deadman´s handle. The standard built-in INFO-bus makes the connection of a fire brigade control unit and of display de- vices, transmission devices for remote indication units and of other information devices using wire- saving techno
ページ19に含まれる内容の要旨
User Manual Series BC216 / Part A Chapter 2 Fire detection control panel Series BC216 19 for false fire alarms. The fire detection control panel BC216-1, besides automatic adjusting of the sen- sitivity of the detectors, is capable of displaying a dirt message on the control panel before the detec- tors activate false alarms due to dirt, by using ADM-, ADMPRO- as well as addressable conventional technology. The control panel is capable of making a forecast for each detector about the
ページ20に含まれる内容の要旨
20 Chapter 2 Fire detection control panel Series BC216 User Manual Series BC216 / Part A played on the control panel. In addition to the zone number, the fire detection control panels Series BC216 are capable of displaying a zone-specific text for every detector zone and a detector-specific text for every single fire detector. Thereby relevant information is provided for the safety personnel fast and without delay. Besides with automatic and non-automatic fire detectors, the fire dete
