ページ1に含まれる内容の要旨
Chest Press
Assembly Instructions
ページ2に含まれる内容の要旨
Chest Press Assembly Instructions Item Qty Description Part Number Item Qty Description Part Number 1 1 Front Brace 80113XX 22 1 Front Shroud 8024703 2 1 Rear Brace 80114XX 23 4 M10 x 20mm Bolt 3251701 3 1 Tower 79854XX 24 1 Plate 7322301 4 4 M10 x 130mm Bolt 3251720 25 1 Cam Guard 8013201 5 42 3/8” Flat Washer 3102514 26 2 M5 x 10mm Phillips Screw 3239101 6 13 M10 Nylock Nut 3242002 27 1 Seat Pad 72972XX 7 1 Seat Frame 80111XX 28 1 Back Pad 74741XX 8 6 M10 x 90mm Bolt 3251715 29 2 M10 x 35m
ページ3に含まれる内容の要旨
ページ4に含まれる内容の要旨
Chest Press Assembly Instructions 1. LOOSELY assemble the FRONT BRACE (1) and REAR BRACE (2) to the TOWER (3) using four M10 X 130mm BOLTS (4), eight 3/8" SAE WASH- ERS (5) and four M10 NYLOCK NUTS (6) as shown. 2. LOOSELY assemble the SEAT FRAME (7) to the FRONT BRACE (1) and REAR BRACE (2) using four M10 X 90mm BOLTS (8), eight 3/8" SAE WASHERS (5) and four M10 NYLOCK NUTS (6) as shown. 3. LOOSELY assemble the TOP BRACE (9) to the SEAT FRAME (7) and TOWER (3) using two M10 X 90mm BOLTS (8), fo
ページ5に含まれる内容の要旨
5. Insert the PIVOT SHAFT (11), LONG SPACER (12), two BEARINGS (13) and two SMALL SPACER (14) into the WORKARM (15) as shown. Carefully insert the WORKARM into the FRONT BRACE (1) and secure it with two M10 X 25mm BOLTS (16) and two 3/8" SAE WASHERS (5). Tighten the BOLTS securely.
ページ6に含まれる内容の要旨
Chest Press Assembly Instructions 6. Assemble the OUTPUT CAM (17), OUTPUT PLATE (18), and OUTPUT RING (19) using three M10 X 45mm BOLTS (20) and three 3/8" SAE WASHERS (5) as shown. Tighten the BOLTS securely. 7. Assemble the REAR SHROUD (21) and FRONT SHROUD (22) to the TOWER (3) using four M10 X 20mm BOLTS (23), four 3/8" SAE WASH- ERS (5) as shown. Be sure all tabs along the sides and top of the SHROUDS are fully engaged in the slots located inside the TOWER. Tighten the BOLTS securely. Do no
ページ7に含まれる内容の要旨
10. Attach the SEAT PAD (27) to the SEAT FRAME (7) using two M10 X 25mm BOLTS (16) and two 3/8" SAE WASHERS (5). Tighten the BOLTS securely. 11. Attach the BACK PAD (28) to the SEAT FRAME (7) using two M10 X 35mm BOLTS (29) and two 3/8" SAE WASHERS (5). Tighten the BOLTS securely.
ページ8に含まれる内容の要旨
Chest Press Assembly Instructions NOTE: Some components have been removed from the illustration for clarity. 12. Assemble one M10 HEX JAM NUT (30) onto one end of the CABLE (31) approximately 1/2”. Assemble the ROD END BEARING (32) to the same end of the CABLE until it meets the M10 HEX JAM NUT. Tighten the M10 HEX JAM NUT securely. 13. Loosely assemble the ROD END BEARING (32) of the CABLE (31) to the WORK ARM (15) using one M10 X 40mm BOLT (33), SPACER (34), 3/8" SAE WASHER (5) and M10 NYLOCK
