ページ1に含まれる内容の要旨
Owner’s Manual
ST-PR
Questions?
Call Us Toll Free
Keys Fitness Helpline
1-888-340-0482
Model Name : ST-PR
Manufactured Date :
PO # :
Model Name Decal Location
215-00090
08/06 Rev B
ページ2に含まれる内容の要旨
Table of Contents Important Safety Information 3 Assembly 4-11 Parts List 12 Exploded View 13 Warranty Information 14 2
ページ3に含まれる内容の要旨
Important Safety Information Please read all instructions carefully before using this product. SAFETY TIPS Consult with your physician before engaging in any vigorous exercise. Know your heart rate and/or pulse as well as your physician-recommended heart rate training zone. Proper medical clearance is recommended for anyone beginning an exercise program especially if you are 35 years of age or older or suffer from heart respiratory problems. - Warm-up before any exercise program with 8 minu
ページ4に含まれる内容の要旨
Assembly Assembly Hardware 4
ページ5に含まれる内容の要旨
Assembly NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. STEP 1 Connect the Left and Right Stabilizer (#1) & (#2) by a Rear Stabilizer (#3). Align the holes and secure themwith one 6 ¼”x 2”Bracket (#41), two M10 x 90 Carriage Bolts (#37), Washers Dia10 (#39), and M10 Aircraft Nuts (#38) at each end of the Rear Stabilizer. Attach one Upright Beam (#5) to the Left Stabilizer (#1). Secure it with one 8 ½”x 2 ¾”Bracket (#12), twoM10 x 70 Carriage Bolts (#36), Washers
ページ6に含まれる内容の要旨
Assembly NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. STEP 2 Attach the Left Support (#6) onto the Left Stabilizer (#1). Secure it with one 4 ¾”x 2” Bracket (#42), two M10 x 70 Carriage Bolts (#36), Washers Dia10 (#39), and M10 Aircraft Nuts (#38) from the bottom up. Attach the front of the Left Support (#6) to the Left Upright Beam(#5). Secure it with one M10 x 20 Hex Bolt (#35) and Washer Dia10 (#39). Repeat Step A & B above to install the Right Support (#7) on
ページ7に含まれる内容の要旨
Assembly NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. STEP 2 Cont. Attach the bottomof Vertical Frame (#8) to the bracket on the Rear Stabilizer (#3). Secure the Vertical Frame to the Rear Stabilizer with two M10 x 20 Hex Bolts (#35) and Washers Dia10 (#39). Secure the Vertical Frame (#8) to the Cross Brace (#4) with two M10 x 70 Carriage Bolts (#36), one 5 1/8”x 2 ¾”Bracket (#19), two Washers Dia10 (#39), and M10 Aircraft Nuts (#38). Attach a Bumper (#28) onto
ページ8に含まれる内容の要旨
Assembly NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. STEP 3 Slide the Sliding Weight Holder (#10) onto the Vertical Frame (#8). Attach two Spring Clips 1”(#31) to the posts on the Sliding Weight Holder. Insert the Upper Frame (#9) onto the top opening on the Vertical Frame (#8). Align the bottomhole on the top of the Vertical Frame. Secure it with one M10 x 80 Hex Bolts (#43) and two Washers Dia10 (#39). Attach the Lat Bar Holder (#26) to the front of Upper Fram
ページ9に含まれる内容の要旨
Assembly NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. STEP 4 Notice: The cable diagram below shows the proper routings of the 110”Lat Cable (#20), the 92” Low Row Cable (#16) for the cable assembly in Steps 4 Use the diagram to be sure that the two cables have been assembled correctly. If the cables have not been correctly rout- ed, the Machine will not function properly and damage may occur. Draw the end, without the rubber ball, of the 110”Lat Cable (#20) to the
ページ10に含まれる内容の要旨
Assembly NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. STEP 4 Cont. 10
ページ11に含まれる内容の要旨
Assembly NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. STEP 5 Attach two Weight Plate Holders (#13) to the holes on the side of each Left and Right Supports (#6) &(#7). Secure each with a M10 x 20 Hex Bolt (#35) and Washer Dia10 (#39). Attach a Spring Clip 1”(#31) to each weight plate holder. Insert the two Bar Catches (#15) into upper selected hole on the left and right Upright Beam. Insert the two Long Bar Catches (#17) into the bottomhole on the Left and Upri
ページ12に含まれる内容の要旨
Parts List ST-PR Parts List Rev A Ref # Part # Description Qty 1 223-00861 LEFT STABALIZER, ST-PR 1 2 223-00862 RIGHT STABALIZER, ST-PR 1 3 223-00863 REAR STABALIZER, ST-PR 1 4 223-00864 CROSS BRACE, ST-PR 1 5 223-00865 UPRIGHT BEAMS, ST-PR 2 6 223-00866 LEFT SUPPORT, ST-PR 1 7 223-00867 RIGHT SUPPORT, ST-PR 1 8 223-00868 VERTICAL FRAME, ST-PR 1 9 223-00869 UPPER FRAME, ST-PR 1 10 219-00340 SLIDING WEIGHT HOLDER, M-PR 1 11 223-00400 LAT BAR#11 M-PR/ST-PR 1 12 210-00168 BRACKET, 8 ½ X 2 ¾ M-P
ページ13に含まれる内容の要旨
Exploded View 13
ページ14に含まれる内容の要旨
Warranty KEYS FITNESS PRODUCTS, L.P. STRENGTH TRAINER WARRANTY Keys Fitness Products L.P. warrants this product for a period of 90 days on parts and lifetime on the frame from the original date of purchase. This warranty covers the product from defects in materials and workmanship for the original purchaser. Using this product for commercial purposes, products damaged by misuse, abuse, or from shipping, moving and storage will void this warranty. Replacement parts are available from Keys
ページ15に含まれる内容の要旨
Keys Fitness Products, L.P. 4009 Distribution Drive, Suite 250 Garland, Texas 75041 Customer Service: 1-888-340-0482
