ページ1に含まれる内容の要旨
Z100 / Z300 Z500
Z700
OWNER’S MANUAL
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE
OPERATING YOUR NEW ELLIPTICAL!
ページ2に含まれる内容の要旨
Table of Contents Product Registration . 2 Important Safety Instructions 3 Important Electrical Information 4 Important Operation Instructions ..4 E25 Assembly Instructions .5 E55 Assembly Instructions .11 Operation of Your New Elliptical ...17 Manufacturer s Limited Warranty ..30 ATTENTION-THIS ELLIPTICAL IS INTENDED FOR RESIDENTIAL USE ONLY AND IS WARRANTED FOR THAT APPLICATION. ANY OTHER APPLICATION VOIDS THIS WARRANTY IN ITS ENTIRETY. 1
ページ3に含まれる内容の要旨
CONGRATULATIONS ON YOUR NEW ELLIPTICAL AND WELCOME TO THE SOLE FAMILY! Thank you for your purchase of this quality elliptical trainer from Sole. Your new elliptical was manufactured by one of the leading fitness manufacturers in the world and is backed by one of the most comprehensive warranties available. Sole will do all we can to make your ownership experience as pleasant as possible for many years to come. If you have any questions about your new product or questions about the warranty conta
ページ4に含まれる内容の要旨
Important Safety Instructions WARNING - Read all instructions before using this appliance. Do not operate elliptical on deeply padded, plush or shag carpet. Damage to both carpet andelliptical may result. Keep children away from the elliptical. There are obvious pinch points and other caution areas that can cause harm. Keep hands away from all moving parts. Never operate the elliptical if it has a damaged cord or plug. If the elliptical is not working properly, call your dealer. Keep the c
ページ5に含まれる内容の要旨
Important Electrical Information WARNING! NEVER remove any cover without first disconnecting AC power supply. If A.C. voltage varies by ten percent (10%) or more, the performance of your elliptical may be affected. Such conditions are not covered under your warranty. If you suspect the voltage is low, contact your local power company or a licensed electrician for proper testing. NEVER expose this elliptical to rain or moisture. This product is NOT designed for Use outdoors, near a pool or spa
ページ6に含まれる内容の要旨
Assembly Instructions (E25) UNPACKING THE UNIT 1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along the dotted Line. Lift Box over the unit and unpack. 2. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged parts are found, or parts are missing, contact your dealer immediately. 3. Locate the hardware package. The hardware is separated into steps. Remove the tools first. Remove the hardware for each step as needed to avoid conf
ページ7に含まれる内容の要旨
STEP 2: HANDLE BAR ASSEMBLY 1. Ins tall the 2 pc s of 1 7m/m Wave Was h ers o nto the Le ft and Right s ide of the Handle Bar axle. 2. Slide the Left and Right Handle Bars onto the appropriate side of the axle. 3. Put the 2 pcs of 5/16" x 23 x 1.5T Flat Washers onto the 2 pcs of 5/16" x 15m/m Hex Head Screws and install, and tighten, in the threaded holes in the ends of the axle. STEP 3: CONNECTING ARM ASSEMBLY 1. Align the hole in the end of the Connecting arm (L)(pivoting rod end) with the hol
ページ8に含まれる内容の要旨
ページ9に含まれる内容の要旨
ページ10に含まれる内容の要旨
ページ11に含まれる内容の要旨
ページ12に含まれる内容の要旨
Assembly Instructions (E55) UNPACKING THE UNIT 1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along the dotted Line. Lift Box over the unit and unpack. 2. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged parts are found, or parts are missing, contact your dealer immediately. 3. Locate the hardware package. The hardware is separated into steps. Remove the tools first. Remove the hardware for each step as needed to avoid conf
ページ13に含まれる内容の要旨
6. Using the two sided wrench tighten the three bolts, and the fourth bolt which is pre-installed, firmly. These bolts should be tightened as much as you possibly can. 7. Locate the electronic console and the four 1/2 X 1/4 Phillips head screws. 8. There will be three electrical wire connectors at the top opening of the console mast, two 2 pin (hand pulse sensors), one 10 pin (main wire harness). Connect these to the mating connectors on the back of the console. The connectors are keyed so you
ページ14に含まれる内容の要旨
bolt using two wrenches provided. You have to put a wrench on both axle bolts to tighten firmly. 6. Align the hole in the end of the connecting arm (pivoting rod end) with the hole in the bracket of the handle bar. The rod end should be on the inside of the handle bar bracket. Take one of the 1-1/4 X 3/8 bolts and install it through the handle bar bracket and the rod end. Install a flat washer and Nylon nut on the bolt and tighten firmly using a wrench on the nut and one on the bolt. 7. Repeat
ページ15に含まれる内容の要旨
ページ16に含まれる内容の要旨
Step3/ 4 15 E25 / E55 Elliptical
ページ17に含まれる内容の要旨
Features Adjustable foot pedals, and orthopedically correct foot pads E55 only Through research performed with a leading sports scientist and physical rehabilitation expert, Sole engineering has developed a breakthrough in pedal design. No other elliptical, at any price, offers these unique features. The history of elliptical use over the past few years tells us that many users suffer from numb toes while working out on elliptical trainers. Many other users complain of ankle, Achilles tendon, kn
ページ18に含まれる内容の要旨
ページ19に含まれる内容の要旨
ページ20に含まれる内容の要旨
Programming the console Each of the programs can be customized with your personal information and changed to suit your needs. Some of the information asked for is necessary to ensure the readouts are correct. You will be asked for your Age and Weight. Entering your Age is necessary during the Heart Rate control programs to ensure the correct settings are in the program for your Age. Otherwise the work settings could be too high or low for you. Entering your Weight aides in calculating a more cor
