ページ1に含まれる内容の要旨
Steam press
Prensa de planchar
USK SIT 25803
www.KALORIK.com
120V~60Hz 1000W
ページ2に含まれる内容の要旨
IMPORTANT SAFEGUARDS 1. READ ALL INSTRUCTIONS 2. Use this appliance for its intended use only. 3. Check that your mains voltage corresponds to that stated on the appliance. 4. To protect against a risk of electric shock, do not immerse the appliance in water or other liquids. 5. The iron should always be turned to OFF before plugging in or unplugging from outlet. Never yank cord to disconnect from outlet: instead, grasp plug and pull to disconnect. 6. Do not allow cord to to
ページ3に含まれる内容の要旨
pulled or tripped over. 15. If the supply cord is damaged, disconnect the appliance from the socket immediately and the supply cord must be replaced by the manufacturer, its service agent or a similarly qualified person in order to avoid a hazard. 16. Do not operate the appliance if it has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the appliance, take it to a service agent or a similarly qualified person for examination and repair. Incorrect reassemb
ページ4に含まれる内容の要旨
SAVE THESE INSTRUCTIONS POLARIZED PLUG INSTRUCTIONS This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug will fit into the polarized outlet only one way. If the plug does not properly fit into the outlet at first, reverse it. If it still does not fit, contact a competent qualified electrician. Do not attempt to modify the plug in any way. For appliances equipped with a standard plug, simply insert the plug into the
ページ5に含まれる内容の要旨
PART DESCRIPTION 5 USK SIT 25803 - 080425
ページ6に含まれる内容の要旨
These accessories are included with your appliance. Carefully check to make sure you have all the parts listed below. Unit Features & Accessories 1. Hanger 2. Pole 3. Steam Iron 4. Iron Holder 5. Fabric Brush 6. Iron Bracket 7. Ironing Board 8. Main Bracket 9. Tilted Bracket 10. Steam Adjustment Knob 11. Water Reservoir Cap 12. Water level indicator light 13. Power Switch 14. Lock Button 15. Pole Fix Nut 16. Unlock Button 17. Rear Wheel 18. Bottom Cover 19. Water Filling C
ページ7に含まれる内容の要旨
Figure1: Take the main bracket with ironing board part from package. First insert the pole fixing nuts (part 15) into each pole then slide the bracket into the holes at the back of the front cover (Part 18). Then push the two fixing nuts down to secure the bracket firmly. Figure 2: Inset the 2 shafts of the tilted bracket into the front holes of the front cover, by positioning the black pegged parts into correct position. Push down to fix firmly. Figure 3: Clip on the two shaft co
ページ8に含まれる内容の要旨
Figure 8: Attaching the iron holder: Align the holes of the iron holder with the slots on the side of the iron bracket, and push down to fix. Figure 9: Attaching iron bracket to the frame: take the assembled iron bracket (6), making sure the iron holder faces towards the ironing board, then align the two pillar connectors with main bracket holes and push down to lock. Figure 10: Assemble the pole: Insert the pole into the hole at the top of the iron bracket. Figure 11: Attachin
ページ9に含まれる内容の要旨
INSTRUCTIONS FOR USE FILLING RESERVOIR WITH WATER Note: When the water level is low, the water level indicator will illuminate. It is normal to hear a pumping sound coming from the water reservoir when the water level is low. Adding water will stop the sound. Caution: Be sure that the power is OFF and the appliance is unplugged before filling the water reservoir with water. Warning: To prolong the life of this product and to ensure that the ironing station’s performance is optim
ページ10に含まれる内容の要旨
STEAM SETTINGS Figure 16 Both buttons can be either held down manually or locked into position for ease of use when ironing or steaming for a lengthy period of time. For ordinary steam, press and hold or press and lock the left button. For the steam jet first press and lock the steam button and then press and lock the steam jet button. Should you only want a short burst of steam, simply hold the steam jet button down for a few seconds whilst using regu
ページ11に含まれる内容の要旨
Figure 17 ATTACHING FABRIC BRUSH TO IRON CAUTION: Use care when attaching fabric brush, as the sole plate may be hot. Do not attempt to attach fabric brush while appliance is emitting steam. As shown in figure 18 below, slide the fabric brush over the sole plate until it clicks in place. When the fabric brush is clipped in place you may begin steaming. OPERATING THE IRONING STATION 1. NOTE: The very first time you use the ironing station, turn the steam
ページ12に含まれる内容の要旨
2. To prevent the appliance moving freely during use, push down the lock button on the front to lock the appliance in place. Figure 19 3. Plug power cord into a convenient electrical outlet. 4. Set Lighted ON/OFF switch to “ON”, and check that the switch is illuminated, the heater indicator light will illuminate indicating that heater is active. 5. After approximately 30 to 40 seconds of heating time, the unit will be ready for use.
ページ13に含まれる内容の要旨
material you are steaming. Using light back and forth motions over the area you are steaming will further enhance the process. If use for a long period of time, some water might be sprinkled on the clothes if used from too near. 8. Press ironing your clothes: Detach the brush, and lay the fabric flat on the ironing board, push and lock the left steam button and then press the sole plate on the fabric and make back and forth movements, after several motions, the clothes will be ironed.
ページ14に含まれる内容の要旨
PROPER STORAGE 1. Turn the power switch to OFF and unplug power cord from electrical outlet. 2. Allow unit to cool completely(at least 30 minutes) 3. Remove the Fabric brush attachment from unit (if attached, please refer to following detaching steps) A. Use your finger to push the back of the fabric brush to unlock it.(figure 21) B. Gently slide the fabric brush off the sole plate. CAUTION: Do not attempt to detach the brush if the iron plate is hot!! Figure 21
ページ15に含まれる内容の要旨
6. Wrap the power cord onto the cord clamp on the main bracket, as figure 23 shows. 7. Set the ironing board to the lowered position as shown in figure 23. 8. Store the ironing station in a cool, dry place. Figure 23 MAINTENANCE CHANGING THE FILTER CARTRIDGE The filter cartridge is located inside the water reservoir. The filter cartridge needs to be changed every 3 months. Failure to do so will invalidate this appliance’s warranty. Before changing t
ページ16に含まれる内容の要旨
Each new unit of the ironing station comes complete with a new filter cartridge already inside the water reservoir and a spare filter cartridge. Thereafter you will need to contact the retailer to purchase replacement filter cartridges. The spare filter cartridge can be found in the space under the ironing board as shown in figure 25b below. This is to prevent the spare filter cartridge from being misplaced. Figure 25b MI
ページ17に含まれる内容の要旨
recommended that you place a basin or a rag under the iron so as to prevent the ironing board from getting wet. NOTE: This function is solely for the purpose of cleaning the internal structure of this appliance. This function is not to be used during ironing as it will soak the clothes and possibly stain the clothes with the mineral residue that is being cleaned out of the system. Figure 26 Caution: The steam being emitted during the self clean is very strong and very hot. Take ca
ページ18に含まれる内容の要旨
allow proper time Steam button is Press and hold the steam for the unit not being button for a few seconds to heat up and pressed for steam to begin flowing begin producing steam) Steam output Steam jet holes Use “self clean” function power is reduced have mineral cleaning for 3 minutes. or intermittent. build up blocking the steam. Loud pumping Low water Refill water reservoir sound when steam level in water according to filling button is pressed. reservoir. procedure Dirt/ miner
ページ19に含まれる内容の要旨
DISPOSAL OF THIS APPLIANCE This unit is marked to show that it should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can inform you where to return this product for e
ページ20に含まれる内容の要旨
WARRANTY We suggest that you complete and return the enclosed Product Registration Card promptly to facilitate verification of the date of original purchase. However, return of the Product Registration Card is not a condition of these warranties. You can also fill this warranty card online, at the following address: www.KALORIK.com This KALORIK product is warranted for 1 year from the date of purchase against defects in material and workmanship. This warranty is not transferable. Kee
