ページ1に含まれる内容の要旨
Operating Instructions and Parts Manual
Mini Lathe
Models JML-1014I and JWL-1220
WMH TOOL GROUP
2420 Vantage Drive
Elgin, Illinois 60123 Part No. M-708376
Ph.: 800-274-6848 Revision A 9/06
www.wmhtoolgroup.com Copyright © WMH Tool Group
ページ2に含まれる内容の要旨
WARRANTY AND SERVICE WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these WMH Tool Group Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and major repair on your JET® tools. For the name of an Authorized Service Center in your area call 1-800-27
ページ3に含まれる内容の要旨
Table of Contents Table of Contents ...............................................................................................................................3 Warning .............................................................................................................................................4 Specifications .....................................................................................................................................6 Optional Accessories Availab
ページ4に含まれる内容の要旨
Warning For your own safety, read this instruction manual before operating the lathe. Wear eye protection. Do not wear gloves, necktie, or loose clothing. Tighten all locks before operating. Rotate the workpiece by hand before applying power. Rough out the workpiece before installing on the faceplate. Do not mount a split workpiece or one containing a knot. Use the lowest speed when starting a new workpiece. • Keep guards in place and in working order. • Remove adjusting keys and w
ページ5に含まれる内容の要旨
• Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury. • Some dust created by power sanding, sawing, grinding, drilling and other construction activities contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead based paint. • Crystalline silica from bricks, cement and other masonry products. • Arsenic and chromium
ページ6に含まれる内容の要旨
Specifications Model Number..........................................................JML-1014I.............................................JWL-1220 Stock Number .............................................................. 708375.................................................708376 Swing Over Bed (in.).............................................................10........................................................ 12 Swing Over Tool Rest Base (in.)....................................
ページ7に含まれる内容の要旨
Electrical Requirements In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not modify the plug provided. If it will not fit the outlet, have the pr
ページ8に含まれる内容の要旨
Unpacking 1. Remove contents from the shipping box. 2. Inspect contents for shipping damage and report damage, if any, to your distributor. 3. Be sure to keep the box and packing material should you need to pack the lathe for moving. 4. Do not clean the lathe with anything other than a damp cloth or a mild solvent. Use of heavy solvents, paint thinner, gasoline, etc. will damage painted surfaces. Contents of the Shipping Carton: JML-1014I
ページ9に含まれる内容の要旨
Operations Tailstock Movement Tailstock Handwheel (A, Figure 2) – Turn clockwise to move tailstock spindle forward. Turn counterclockwise to retract tailstock spindle. Tailstock Spindle Lock (B, Figure 2) – Locks tailstock spindle. Release to adjust with handwheel. Tailstock Lock (C, Figure 2) – Locks tailstock in position on the bed. Release to move the Figure 2 tailstock assembly closer to or farther from the headstock. The tailstock spindle is hollow. This can be useful for i
ページ10に含まれる内容の要旨
Face Plate (Figure 6) – Screws on to the headstock and is used in face plate turning operations. Mount your workpiece onto the faceplate with brass screws (not provided). Make sure the screws are not so long that they will enter the area of the workpiece where the material is to be removed. To remove the face plate from the spindle, place the drift rod into hole (A, Figure 6) and let the drift rod contact the bed of the lathe for leverage. Then unscrew the face plate. Drift Rod (Fig
ページ11に含まれる内容の要旨
4. Move the belt (E, Figure 9) to the desired pulley groove according to the speed chart found on the inside of the headstock access door. Be sure the belt is aligned with spindle pulley and motor pulley. 5. Tension the belt by pushing down on the motor plate handle (D, Figure 11) and re- tighten lock handle (C, Figure 11) Belt Replacement 1. Disconnect the machine from the power source (unplug). Figure 10 2. Open the access doors at the left side of the base (A, Figure 9) and at t
ページ12に含まれる内容の要旨
Index Pin The index feature allows you to cut evenly spaced features in a workpiece while keeping the Lathe headstock spindle locked; for example, when cutting flutes on a spindle blank with a router, while the spindle blank is secured within the Lathe centers. There are 24 index positions on the lathe. 1. To use the index pin (Figure 13), screw it farther into the headstock until it engages a hole in the spindle pulley. 2. Make your first flute cutting. Figure 13 3. Unscrew the
ページ13に含まれる内容の要旨
JML-1014I Mini Lathe 13
ページ14に含まれる内容の要旨
Parts List for JML-1014I Mini Lathe Index No. Part No. Description Size Qty 1.............. JML1014-101 ..........Headstock..........................................................................................1 2.............. JML-2......................Faceplate.........................................................3”...............................1 3.............. JML-3......................Spur Center......................................................MT2..........................
ページ15に含まれる内容の要旨
58............ JML-58....................Eccentric Locking Rod ........................................................................1 59............ JML-59A..................Lock Handle Assembly, Tailstock.........................................................1 60............ JML-60W.................White Tailstock ...................................................................................1 61............ JML-61....................Hand Wheel ......................................
ページ16に含まれる内容の要旨
JWL-1220 Lathe 16
ページ17に含まれる内容の要旨
Parts List for JWL-1220 Lathe Index No. Part No. Description Size Qty 1.............. JWL1220-101 ..........Headstock..........................................................................................1 2.............. JML-2......................Faceplate.........................................................3”...............................1 3.............. JML-3......................Spur Center......................................................MT2...........................1 3A
ページ18に含まれる内容の要旨
55............ JML-55....................Tailstock Spindle ................................................................................1 56............ JML-56....................Leadscrew .........................................................................................1 57............ JML-57....................E-Ring .............................................................ETW-12 .....................1 58............ JML-58....................Eccentric Locking Rod ............
ページ19に含まれる内容の要旨
Electrical Connections for JWL-1220 19
ページ20に含まれる内容の要旨
WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800-274-6848 www.wmhtoolgroup.com 20
