ページ1に含まれる内容の要旨
Installation/Operation Instructions
for
Shower Towers
EC30000 Ristorre™ Onda™
EC31000 Ristorre™ Ovale™
EC33000 Ristorre™ Metallo™
Ovale™ Onda™ Metallo™
Save These Instructions for Future Use.
Complete and mail-in the product registration card provided with your unit.
Write and save the model and serial number of your unit.
Installer: Leave this manual for homeowner.
Homeowner: Read this manual and keep for future reference.
Copyright © by Jacuzzi Whirlpool Bath FZ7
ページ2に含まれる内容の要旨
SAFETY INSTRUCTIONS NOTE: mInImum W aTeR PReSSuRe FoR THeSe SySTemS IS 40 PSI. WARNINg : WHen uSIng THIS unIT , BaSIC PReCauTIonS SHouLd aLW ayS Be FoLLoWed, InCLudIng THe FoLLoWIng: DANgER : do noT PLaCe oR uSe eLeCTRICaLL y ConneCTed devICeS, SuCH aS TeLevISIon, RadIo, oR STeReo SPeakeRS, LIgHTS, HaIR dR yeRS, oR TeLePHoneS, WITHIn 1.5 m (5 FeeT) oF SHoWeR. IMPORTANT: Read all instructions before beginning installation. Consult local codes for requirements. Owner's Record date Purchased _
ページ3に含まれる内容の要旨
Ristorre™ Ovale™ Shower Tower — Specifications optional-Supplied Temperature Check Spout DIMENSIONS SHIPPINg WEIgHT 3" ( 76 mm) d (depth) 7 lb 10-1/4" ( 60 mm) W (13.3 kg) 46-5/8" (1184 mm) H Product specifications are subject to change without notice. PRODUCT WEIgHT lb (10 kg) minimum Working Water Pressure 1.76 psi (1.5 bar) maximum Working Water Pressure 7.5 psi (5.0 bar) Recommended Working Water Pressure 43.51 psi (3.0 bar) maximum Working Water Temp. 140-158° F (60 –
ページ4に含まれる内容の要旨
Ristorre™ Onda™ Shower Tower — Specifications optional-Supplied Temperature Check Spout DIMENSIONS SHIPPINg WEIgHT 3" ( 76 mm) d (depth) 9 lb 13-1/" ( 343 mm) W (13. kg) 51-1/4" (130 mm) L Product specifications are subject to change without notice. PRODUCT WEIgHT 5 lb (11 kg) minimum Working Water Pressure 1.76 psi (1.5 bar) maximum Working Water Pressure 7.5 psi (5.0 bar) Recommended Working Water Pressure 43.51 psi (3.0 bar) maximum Working Water Temp. 140-158° F (60 –
ページ5に含まれる内容の要旨
Ristorre™ Metallo™ Shower Tower — Specifications optional-Supplied Temperature Check Spout DIMENSIONS SHIPPINg WEIgHT -1/ " ( 63.5 mm) d (depth) 9 lb 1-3/4" ( 1905 mm) W (13. kg) 55-7/8" (1419 mm) L Product specifications are subject to change without notice. PRODUCT WEIgHT 6 lb (1 kg) minimum Working Water Pressure 1.76 psi (1.5 bar) maximum Working Water Pressure 7.5 psi (5.0 bar) Recommended Working Water Pressure 43.51 psi (3.0 bar) maximum Working Water Temp. 140-158° F
ページ6に含まれる内容の要旨
Ristorre™ Ovale™ Shower Tower — Component Identification 8 9 4 10 7 18 11 1 5 15 17 18 19 17 14 6 4 5 7 3 0a 0b 0c 13 1 6 1 16 13 8 no. name Qty Remark no. nam e Qty Remark 1 Tempered glass Front Plate 1 16 S.S.Flexible Hose 1 Included Body Jet 6 17 Hand Shower Bracket 1 Included 3 Wall mount Shower 1 Included 18 Plastic anchor 5 Included 4 Shower arm 1 Included 19 Screw(m3.5x5mm) 1 Included 5 Back Housing 1 0a diverter 1 6 gasket 1 Included 0b Flow Control 1 7 Wall mount
ページ7に含まれる内容の要旨
Ristorre™ Onda™ Shower Tower — Component Identification 4 10 9 8 7 11 18 1 3 19 17 18 14 15 5 17 0a 0b 3 4 7 6 5 0c 1 13 1 6 16 13 8 FRONT SIDE BACK no. name Qty Remark no. nam e Qty Remark 1 Tempered glass Front Plate 1 16 S.S.Flexible Hose 1 Included Body Jet 6 17 Hand Shower Bracket 1 Included 3 Wall mount Shower 1 Included 18 Plastic anchor 5 Included 4 Shower arm 1 Included 19 Screw(m3.5x5mm) 1 Included 5 Back Housing 1 0a diverter 1 6 gasket 1 Included 0b Flow Contr
ページ8に含まれる内容の要旨
Ristorre™ Metallo™ Shower Tower — Component Identification 10 21 11 1 3 6 8 24 23 27 26 2 14 15 25 20a 17 9 20b 20c 19 18 19 18 12 13 7 7 Wall 22 21 16 13 28 no. name Qty Remark 1 Front Plate 1 Body Jet 6 3 Wall mount Shower 1 mirror 1 6 7 Hanger Included 8 Screw Included 10 Connection rod 1 Included 19 Screw 6 Included Parts List The parts list table common to all Ristorre shower towers is located on Page 9. Please refer to this table for com- ponent identification of parts list in all R
ページ9に含まれる内容の要旨
Common Parts List Qty Remark Qty Remark name name 1 Square Temp Check Spout 1 0c Thermo-Static Control 1 Tube Temp Check Spout 13 1 1 Sealing Washer 5 14 glass Shelf assembl y 1 Threaded Connector 1 15 Hand Shower 1 3 Brass nut 16 Shower Flexible Hose 1 4 Spring Washer 17 Hand Shower Bracket 1 5 Washer Plate 18 Plastic anchors 6 6 Silica gel Washer 19 (m3.5X5mm) Screws 6 7 Ring 0a diverte r 1 8 Washer 1 0b Flow Control 1 Jacuzzi Whirlpool Bath: Shower Towers Page 9 FZ710
ページ10に含まれる内容の要旨
INSTALLATION IMPORTANT: Read all instructions before beginning installation. Consult local codes for requirements. Each unit arrives ready for installation, completely equipped with plumbing and fittings. Remove the unit from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. CAUTION: do not drop the shower tower. dropping the unit may damage its appearance and function. Immediately upon receipt, inspect the unit before installing. Should inspe
ページ11に含まれる内容の要旨
Assemble and Install the Shower Tower 1. attach the shower arm and prepare the glass shampoo Figure 4 platform as follows. a. attach the shower arm (4) to the front plate (1) with 1 4 screw nut (11), see Figure 4. Confirm the screen washer at the water inlet fitting of the wall mount shower head (3) is in place and screw the shower head onto the shower arm by hand. Finally, place a sealing washer (1) into the end connector of the 11 flexible tubing as shown in the Figure, and fasten 3
ページ12に含まれる内容の要旨
. Connect 1/" hoses from the front plate (1) marked in red and blue to the hot and cold water supply’s, respectively, as shown in Figure 7. COLD WATER SUPPLY NOTE: do not bend or kink the hoses Figure 7 BLUE HOSE when installing. Tighten fittings with a RED HOSE wrench and test for leaks. 3. align the three mounting holes of the back housing (5) and front plate (1) with the three HOT WATER mounting rods (7) on wall. Fasten the front SUPPLY plate to the fixing rods and attach with the
ページ13に含まれる内容の要旨
4. using the dimensions indicated in Figure 9, drill two holes 1/4” diameter by 1-3/8” deep into the wall on the right hand side of the shower tower. Insert the plastic anchors (18) into each of the holes, and mount the bracket (17) onto the wall using the m3.5x5mm Screws (19). Figure 9 9-7/8" (250mm) 17 16 19 18 19 18 2" (23mm) 2HOLES 1/4"DIA.(6,4mm)x 1-3/8"(35mm) DEEP 63" (1600mm) 2HOLES 1/4"DIA.(6,4mm)x 1-3/8"(35mm) DEEP TOFLOOR 5. Confirm the sealing washer (21) is inside the end of the
ページ14に含まれる内容の要旨
OPERATION 1. CONTROL VALVE. The Control valve consists of three parts, the diverter (0a), flow control (20b), and thermo-static control (20c). a. Diverter 20a The diverter (0a) works as a function selection. Four icons on the diverter indicate the function selected. The four icons represent the following four functions: Hand shower spray , Body jets , Wall mount spray , and Bath spout . b. Flow Control 20b The Flow Control (4b) is located in the center of the Control valve and is
ページ15に含まれる内容の要旨
Jacuzzi Whirlpool Bath Limited Warranty Shower System Product WARRANTY COVERAgE Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Shower System product (“unit”) who purchases the product for personal or single family use (“user”). The Company will repair or replace, at its option, the unit or its equipment in accordance with the following terms and conditions. ONE YEAR LIMITED WARRANTY ON SHOWER SYSTEM
ページ16に含まれる内容の要旨
Warranty Registration Card This card must be filled out and returned to the address printed on the other side within thirty (30) days from date of purchase in order for this warranty to be come effective. Purchaser's name __________________________________________ Purchaser's address ________________________________________ City _____________________________ State ______Zip _________ date
