ページ1に含まれる内容の要旨
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
MARCY HOME GYM
Safety Notice
MWM-1558
Hardware Identifier
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MWM-1558
Retain This
Manual for
Reference
07-20-05
IMPEX INC.
OWNER'S
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
MANUAL
www.impex-fitness.com
info@im
ページ2に含まれる内容の要旨
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES...................................................................……….. 2 HARDWARE PACK……….....….....................................................................……….. 3 ASSEMBLY INSTRUCTIONS.........................................................................……….. 6 PARTS LIST………………………………………………………………………………….. 17 RESISTANC
ページ3に含まれる内容の要旨
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one per
ページ4に含まれる内容の要旨
HARDWARE PACK 3
ページ5に含まれる内容の要旨
HARDWARE PACK 4
ページ6に含まれる内容の要旨
HARDWARE PACK 5
ページ7に含まれる内容の要旨
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches, two Allen Wrenches, and one Philips Screwdriver. NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Front Vertical Frame (#3) to the Main Base Frame (#8). Secure it with two M10 x 2 ¾” Carriage Bolts (#77), one 5 ½” x 2” Bracket (#25), two Ø ¾” Washers (#80), and two M10 Aircraft Nuts (#82). DO NOT ti
ページ8に含まれる内容の要旨
STEP 2 (See Diagram 2) A.) Slide the 9 Weight Plates (#29) onto the Guide Rods (#20). Align the holes of the Weight Plates. Insert the Selector Rod (#13) through the center hole. Use a L-shaped Pin (#30) to select the number of plates. B.) Slide the Selector Stem (#28) onto the Guide Rods. C.) Attach the Upper Frame (#4) to the two Guide Rods. Place the Upper Frame onto the Front Vertical Frame (#3). D.) Secure the Upper Frame to the Guide Rods with two M10 x 1” Allen Bolts (#70) and Ø
ページ9に含まれる内容の要旨
STEP 3 (See Diagram 3) A.) Attach the Front Press Base (#11) to the Upper Frame (#4). Secure it with one Long Axle (#43), two Ø ¾” Washers (#80), and two M10 Aircraft Nuts (#82). B.) Attach the Right Butterfly (#6) to the Front Press Base. Secure it with one M6 x 1 5/8” Hex Bolt (#75), Lock Ring (#37), and M6 Aircraft Nut (#83). C.) Slide a Butterfly Foam Roll (#59) onto the Right Butterfly arm. Attach a Front Press Handle (#12) to the Right Butterfly. Secure it with a M10 x 3 3/8” All
ページ10に含まれる内容の要旨
STEP 4 (See Diagram 4) A.) Attach the Main Seat Support (#1) to the Front Vertical Frame (#3). Secure it with two M10 x 3 ½” Carriage Bolts (#76), one 4 ¾” x 2” Bracket (#24), two ∅ ¾” Washers (#80), and two M10 Aircraft Nuts (#82). B.) Attach the Leg Developer (#7) to the bracket on the Main Seat Support. Secure it with a Leg Developer Axle (#44), two M10 x 5/8” Allen Bolts (#71), and two Ø ¾” Washers (#80). C.) Insert two Foam Tubes (#23) halfway through the holes on the Leg Developer
ページ11に含まれる内容の要旨
CABLE LOOP DIAGRAM 10
ページ12に含まれる内容の要旨
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach the 131” Upper Cable (#31) to the opening at the front of the Upper Frame (#4). Note: The Ball Stopper on the cable should be underneath the Frame. B.) Attach a Pulley (#60) to the open bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#69), two Ø ¾” Washers (#80), and one M10 Aircraft Nut (#82). C.) Draw the Cable towards the back of the machine to the open bracket on the Upper Frame. Repeat step B above to install a Pul
ページ13に含まれる内容の要旨
DIAGRAM 5 12
ページ14に含まれる内容の要旨
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach one end of the 119” Butterfly Cable (#33) to the hook on the Right Butterfly (#6). B.) Draw the Cable to the right Swivel Pulley Bracket (#18). C.) Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#69), two Ø ¾” Washers (#80), and one M10 Aircraft Nut (#82). D.) Draw the Cable around the Pulley then downward. Attach the Cable to a Crossed Double Floating Pulley Bracket (#17). Install another Pulley. Let th
ページ15に含まれる内容の要旨
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach the 128” Lower Cable (#32) to the open bracket on the bottom of the Leg Developer (#7). B.) Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#69), two Ø ¾” Washers (#80), and one M10 Aircraft Nut (#82). C.) Draw the Cable underneath the Pulley to the open bracket on the Main Base Frame (#8). Repeat Step B above to install a Pulley. D.) Draw the Cable underneath the Pulley along the top of the Main B
ページ16に含まれる内容の要旨
DIAGRAM 7 15
ページ17に含まれる内容の要旨
STEP 8 (See Diagram 8) A.) Attach a Short Chain (#46) to the Upper Cable (#31) by using a C-clip (#50). Attach the Lat Bar (#14) to the Chain by using another C-clip. Adjust the length of the Chain to obtain desired Lat Bar exercise. B.) Attach a Long Chain (#45) to the Lower Cable (#32) by using a C-clip (#50). Attach the Arm Curl Handle (#15) to the Chain by using another C-clip. Adjust the length of the Chain to obtain the desired Arm Curl exercise. Remove the Chain and the Hand
ページ18に含まれる内容の要旨
PARTS LIST KEY NO. DESCRIPTION Q’ty 51 Front Base Frame End Cap 1 1 Main Seat Support 1 52 Rear Base Frame End Cap 2 2 Rear Base Frame 1 53 2” x 1” End Cap 2 3 Front Vertical Frame 1 54 2 ¾” x 2” End Cap 3 4 Upper Frame 1 55 2” Square End Cap 2 5 Left Butterfly 1 56 Ø 1” Cone-shaped End Cap 3 6 Right Butterfly 1 57 Foam Roll End Cap 4 7 Leg Developer 1 58 Foam Roll 4 8 Main Base Frame 1 59 Butterfly Foam Roll 2 9 Butterfly Pulle
ページ19に含まれる内容の要旨
18
ページ20に含まれる内容の要旨
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Cu
