ページ1に含まれる内容の要旨
NOTE:
Please read all
instructions carefully
before using this product
Table of Contents
MARCY MWB 850
Safety Notice
WEIGHT BENCH
Hardware Pack
Assembly Instruction
Exploded Diagram
Parts List
Warranty
Ordering Parts
Model
MWB 850
Retain This
Manual for
Reference
07/17/03
IMPEX INC.
14777 Don Julian Rd., City of Industry, CA 91746
Tel: (800) 999-8899 Fax (626) 961-9966
OWNER'S
www.impex-fitness.com
MANUAL
info@impex-
ページ2に含まれる内容の要旨
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICE....................................................................... 2 HARDWARE PACK………............................................................................... 3 ASSEMBLY INSTRUCTIONS........................................................................... 5 EXPLODED DIAGRAM....................................................
ページ3に含まれる内容の要旨
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should u
ページ4に含まれる内容の要旨
HARDWARE PACK 3
ページ5に含まれる内容の要旨
HARDWARE PACK 4
ページ6に含まれる内容の要旨
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the Right Upright Beam (#3) to a Rear Stabilizer (#14). Secure them with one Bent Bracket (#17), two M10x3 ¾” Carriage Bolts (#47), two ∅ ¾” Washers (#48) and two M10 Aircraft Nuts (#50). Repeat the same procedure to assemble the other side. B
ページ7に含まれる内容の要旨
STEP 2 (See Diagram 2) A.) Connect the Main Seat Support (#1) to a Rear Stabilizer (#14). Secure them with one Bent Bracket (#17), two M10 x 3 ¾” Carriage Bolts (#47), two ∅ ¾” Washers (#48), and two M10 Aircraft Nuts (#50). B.) Connect the Main Seat Support (#1) to the Front Stabilizer (#5). Secure them with one Bent Bracket (#17), two M10 x 3 ¾” Carriage Bolts (#47), two ∅ ¾” Washers (#48), and two M10 Aircraft Nuts (#50). C.) Slide the Sliding Block (#10) onto the Incline Adjus
ページ8に含まれる内容の要旨
STEP 3 (See Diagram 3) A.) Attach two Ø ¾” Bushings (#54) to the pivot on the Main Seat Support (#1). B.) Attach two Backrest Supports (#7) to the Pivot and align the holes. Secure it with one M10 x 6 ¼” Allen Bolt (#39), two ∅ ¾” Washers (#48), and one M10 Aircraft Nut (#50). C.) Attach two Ø ¾” Bushings (#54) to the pivot on the Sliding Block (#10). D.) Attach the holes on the two Backrest Supports to the Pivot. Align the holes. Secure them with one M10 x 6 ¼” Allen Bolt (#39), two
ページ9に含まれる内容の要旨
STEP 4 (See Diagram 4) A.) Attach two Ø ¾” Bushings (#54) to the pivot on the Main Seat Support (#1). Attach the Seat Incline Support Bracket (#8) to the Bushings and align the holes. Secure it with one M10 x 4 ½” Allen Bolt (#40), two Ø ¾” Washers (#48), and one M10 Aircraft Nut (#50). B.) Attach two Ø ¾” Bushings (#54) to the Seat Incline Support Bracket (#8). Attach two Seat Support Frames (#6) to the Bracket and align the holes. Secure them with one M10 x 8 ¼” Allen Bolt (#38), two
ページ10に含まれる内容の要旨
STEP 5 (See Diagram 5) A.) Attach four Ø ¾” Bushings (#54) to the two Seat Support Frames (#6). Attach another four ∅3/4” Bushings (#54) to the two Backrest Supports (#7). B.) Attach a Backrest Support (#7) to a Seat Support Frame (#6). Please note that the Backrest Support should be on the inside of the Seat Support Frame. Secure them with one M10 x 2 3/8” Allen Bolt (#42) and M10 Aircraft Nut (#50). C.) Repeat the same procedure to install the other side. D.) Do not over tighten
ページ11に含まれる内容の要旨
STEP 6 (See Diagram 6) A.) Place the Seat (#22) onto the Seat Support Frame (#6). Secure it with four M8 x 2” Allen Bolts (#44) and Ø5/8” Washers (#49). B.) Place the Backrest Board (#23) onto the Backrest Supports (#7). Secure it with four M8 x 2” Allen Bolts (#44) and Ø5/8” Washers (#49). DIAGRAM 6 10
ページ12に含まれる内容の要旨
STEP 7 (See Diagram 7) A.) Attach the Leg Developer (#4) to the bracket on the top of Main Seat Support (#1). Secure it with one Axle (#16), two M10x ¾” Allen Bolts (#43), and ؾ” Washers (#48). B.) Insert one Foam Roll Tube (#15) halfway through the hole on the Main Seat Support. Insert two Foam Roll Tubes halfway through the holes on the Leg Developer. Push six Foam Rolls (#18) onto the Tubes from both ends. Plug six Foam Roll End Caps (#31) into the Ends. C.) Attach the Arm Curl
ページ13に含まれる内容の要旨
12
ページ14に含まれる内容の要旨
PARTS LIST KEY NO. DESCRIPTION QUANTITY 1 Main Seat Support 1 2 Left Upright Beam 1 3 Right Upright Beam 1 4 Leg Developer 1 5 Front Stabilizer 1 6 Seat Support Frame 2 7 Backrest Support 2 8 Seat Incline Support Bracket 1 9 Arm Curl Stand 1 10 Sliding Block 1 11 Incline Adjustment Bar 1 12 Crutch 2 13 Cross Brace 1 14 Rear Stabilizer 3 15 Foam Roll Tube 3 16 Axle 1 17 Bent Bracket 6 18 Foam Roll 6 19 Spring Clip 3 20 Right Safety Hook 1 21 Left Safety Hook 1
ページ15に含まれる内容の要旨
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Custo
