ページ1に含まれる内容の要旨
NOTE:
Please read all instructions
carefully before using this
product
Safety Notice
IGS-09
Hardware Identifier
OLYMPIC BENCH
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
IGS-09
Retain This
Manual for
Reference
12-11-01
OWNER'S
IMPEX FITNESS PRODUCTS
MANUAL
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
ページ2に含まれる内容の要旨
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE IDENTIFIER.....…....................................................................... 3 ASSEMBLY INSTRUCTIONS........................................................................... 4 EXPLODED DIAGRAM……………………………………………………………... 8 PARTS LIST………………………………
ページ3に含まれる内容の要旨
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one perso
ページ4に含まれる内容の要旨
3
ページ5に含まれる内容の要旨
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Adjustable Wrench and Allen Wrench NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach a Rear Stabilizer (#11) to the bottom of the Upright Beam (#9). Secure it with one Bracket (#15), four M10 x 2 ¾” Carriage Bolts (#12), ∅ ¾” Washers (#13) and M10 Aircraft Nuts (#14). Repeat the same step for the other side. B.) Place the
ページ6に含まれる内容の要旨
STEP 2 (See Diagram 2) A.) Attach the rear of the Main Seat Support (#25) to the Upright Beam (#9). Secure it with two M10 x 2 ¾” Allen Bolts (#16), four ∅ ¾” Washers (#13), and two M10 Aircraft Nuts (#14). Do not tighten the nuts and bolts yet. B.) Slide the Sliding Block (#22) onto the Main Seat Support (#25). Secure it with a Lock Knob (#6). C.) Attach the Front Stabilizer (#40) to the Main Seat Support. Secure it with three M10 x 2 ¾” Allen Bolts (#16), six ∅ ¾” Washers (#13),
ページ7に含まれる内容の要旨
STEP 3 (See Diagram 3) A.) Attach two Seat Supports (#20), one on each side, to the pivot on the Sliding Block (#22). Secure the Seat Supports (#20) to the two rear holes on the Seat Pad (#1) using two M8 x 1 3/4” Allen Bolts (#18) and ∅ ½” Washers (#19). B.) Attach the Seat Incline Adjustment (#27) to the two front holes on the Seat Pad. Secure it with two M8 x 1” Allen Bolts (#26) and ∅1/2” Washers (#19). Place the Seat Incline Adjustment onto the Sliding Block. Insert a L-shaped
ページ8に含まれる内容の要旨
STEP 4 (See Diagram 4) A.) Insert the Leg Developer Holder (#41) into the opening on the Front Stabilizer (#40). Secure it with the Lock Knob (#6). B.) Attach the Leg Developer (#38) to the bracket on the Leg Developer Holder (#41). Secure it with a M12 x 2 3/8” Axle (#36) and M12 Allen Bolt (#45). C.) Secure the Leg Developer (#38) with a 4” Lock Pin (#36). Remove the Pin when using the Leg Developer. D.) Insert a Foam Roll Tube (#32) halfway through the hole on the Leg Developer
ページ9に含まれる内容の要旨
8
ページ10に含まれる内容の要旨
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Seat Pad 1 2 Backrest Board 1 3 2” x 2 ¾” Sleeve 2 4 Crutch 2 5 Olympic Sleeve 1 6 Lock Knob 4 7 Backrest Adjustment Bar 1 8 1 ½” Square End Cap 2 9 Upright Beam 1 10 2” End Cap 6 11 Rear Stabilizer 2 12 M10 x 2 ¾” Carriage Bolt 8 13 ∅ ¾” Washer 18 14 M10 Aircraft Nut 13 15 Bracket 2 16 M10 x 2 ¾” Allen Bolt 3 17 Backrest Support 2 18 M8 x 1 ¾” Allen Bolt 6 19 ∅ ½” Washer 8 20 Seat Support 2 21 1” Square End Cap 4 22 Slidi
ページ11に含まれる内容の要旨
IRON GRIP SPORT By IMPEX FITNESS PRODUCTS LIMITED LIFE TIME WARRANTY IMPEX FITNESS PRODUCTS ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of LIFE TIME on the Frame and Weld, 3 YEARS on parts, and 6 MONTHS on upholstery from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's opti
