ページ1に含まれる内容の要旨
NOTE:
Please read all instructions
carefully before using this
product
Table of Content
Safety Notice
IGS-06
Hardware Identifier
CABLE CROSSOVER
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
IGS-06
Retain This
Manual for
Reference
04-18-02
OWNER'S
IMPEX FITNESS PRODUCTS
MANUAL
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitne
ページ2に含まれる内容の要旨
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE IDENTIFIER.....…....................................................................... 3 ASSEMBLY INSTRUCTIONS........................................................................... 4 EXPLODED DIAGRAM……………………………………………………………... 8 PARTS LIST………………………………
ページ3に含まれる内容の要旨
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one perso
ページ4に含まれる内容の要旨
3
ページ5に含まれる内容の要旨
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Adjustable Wrench and Allen Wrench NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach a Floor Stabilizer (#6) and a Lower Pivot Bracket (#35) to the Base Frame (#3). Secure it with two M12 x 4” Carriage Bolts (#28), ∅ 1” Washers (#29), and M12 Aircraft Nuts (#30). B.) Insert the Lower Pulley Bracket (#14) into the hole on the
ページ6に含まれる内容の要旨
STEP 2 (See Diagram 2) A.) Attach a Support Frame (#2) to the Floor Stabilizer (#6). Secure it with one Bracket (#16), two M12 x 4” Carriage Bolts (#28), ∅ 1” Washers (#29), and M12 Aircraft Nuts (#30). B.) Insert two Guide Rods (#12) into the holes on top of the Base Frame (#3). Secure each Guide Rod with one M10 x 1” Allen Bolt (#38) and ∅ ¾” Washer (#32) from the bottom. C.) Slide one 1” Thick Rubber Bumper (#22) onto each Guide Rod from top. Note: WD40 or similar lubricant might be
ページ7に含まれる内容の要旨
STEP 3 (See Diagram 3 & Cable Loop Diagram) A.) Attach the horizontal beam on the Crossover Frame (#1) to the top of the two Guide Rods (#12). Note: Help of a second or third person is a must!! Secure the Guide Rods with two M10 x 1” Allen Bolts (#38) and ∅ ¾” Washers (#32). Repeat the same procedure to install the other side. B.) Secure each end of Crossover Frame to each Rear Support Frame (#2) with one Bracket (#16), two M12 x 4” Carriage Bolts (#28), two ∅ 1” Washers (#29), and
ページ8に含まれる内容の要旨
DIAGRAM 3 7
ページ9に含まれる内容の要旨
8
ページ10に含まれる内容の要旨
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Crossover Frame 1 2 Support Frame 2 3 Base Frame 2 4 Weight Holder 2 5 Guide Rod Sleeve 4 6 Floor Stabilizer 2 7 Allen Bolt 4 8 Small Pulley Bracket 2 9 Large Upper Pulley Bracket 2 10 ∅ 1” x 1 ½” Brass Bushing 2 11 Handle 4 12 Guide Rod 4 13 Olympic Sleeve 4 14 Lower Pulley Bracket 2 15 ∅ 1” x ¾” Brass Bushing 4 16 Bracket 4 17 Chin Up Grip 2 18 6” Pulley 8 19 4 ½” Pulley 2 20 Cable 2 21 M10 x 1” Round Allen Bolt 8 2
ページ11に含まれる内容の要旨
IRON GRIP SPORT By IMPEX FITNESS PRODUCTS LIMITED LIFE TIME WARRANTY IMPEX FITNESS PRODUCTS ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of LIFE TIME on the Frame and Weld, 3 YEARS on parts, and 6 MONTHS on upholstery from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's opti
