ページ1に含まれる内容の要旨
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Marcy Platinum
Safety Notice
Corner Gym
Hardware Pack
Assembly Instruction
GS 99
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
GS 99
Retain This
Manual for
Reference
Jan-14-05
OWNER'S
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
MANUAL
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitne
ページ2に含まれる内容の要旨
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE PACK……….....…....................................................................... 3 ASSEMBLY INSTRUCTIONS...............................................................…..........6 PARTS LIST…………………………………………………………….……….…….25 RESISTANCE CHART…………………………
ページ3に含まれる内容の要旨
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person
ページ4に含まれる内容の要旨
HARDWARE PACK 3
ページ5に含まれる内容の要旨
HARDWARE PACK 4
ページ6に含まれる内容の要旨
HARDWARE PACK 5
ページ7に含まれる内容の要旨
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Place the Right Base Frame (#1) on a flat surface. Make sure there is enough space around to assemble the machine. B.) Insert four Guide Rods (#9) into the holes on the Right Base Frame (#1). Secure each Guide Rod to the Right Base Frame from the bottom
ページ8に含まれる内容の要旨
STEP 2 (See Diagram 2) A.) Attach the Rear Vertical Frame (#4) to the Right Base Frame (#1). Attach the Left Base Frame (#2) to the Rear Vertical Frame. Align the holes and secure them with two M10 x 2 ¾” Carriage Bolts (#84), ∅ ¾” Washers (#99), and M10 Aircraft Nuts (#96). B.) Do not tighten the Nuts and Bolts yet. DIAGRAM 2 7
ページ9に含まれる内容の要旨
STEP 3 (See Diagram 3) A.) Attach the Right Vertical Beam (#3) to the Right Base Frame (#1). Secure it with two M10 x 2 ½” Carriage Bolts (#85), ∅¾” Washers (#99), and M10 Aircraft Nuts (#96). DO not tighten the Nuts and Bolts yet. B.) Attach the Right Seat Support (#7) to the Right Vertical Beam (#3). Secure it with one M10 x 2 ½” Carriage Bolt (#85), one M10 x 2 3/8” Allen Bolt (#83), one 3 1/8” x 1 ¾” Bracket (#31), two Ø ¾” Washers (#99), and one M10 Aircraft Nut (#96). C.) Attac
ページ10に含まれる内容の要旨
STEP 4 (See Diagram 4) A.) Slide fourteen Weight Plates (#44) onto the rear set of Guide Rods (#9). Make sure the groves on the Plates all face toward the back of the machine. Insert a Selector Rod (#29) into the center holes. Slide a Selector Stem (#45) onto the two Guide Rods. B.) Repeat Procedure A above to install the other fourteen Weight Plates onto the other two Guide Rods. Make sure the grove on the Plate all face toward the front of the machine. C.) Place the Upper Frame
ページ11に含まれる内容の要旨
DIAGRAM 4 10
ページ12に含まれる内容の要旨
STEP 5 (See Diagram 5) A.) Attach the Left Seat Support (#8) to the Left Vertical Beam (#5). Secure it with two M10 x 2 ½” Carriage Bolts (#85), one 4 3/8” x 1 ¾” Bracket (#73), two Ø ¾” Washers (#99), and two M10 Aircraft Nuts (#96). B.) Attach the Left Seat Support (#8) to the Left Base Frame (#2). Secure it with a M10 x 2 ½” Carriage Bolt (#85), Ø ¾” Washer (#99), and M10 Aircraft Nut (#96). C.) Attach the Leg Press Frame (#14) to the Left Base Frame (#2). Secure it with one M12 x 3
ページ13に含まれる内容の要旨
STEP 6 (See Diagram 6) A.) Attach the Front Press Base (#10) to the Right Base Frame (#1). Secure it with one M10 x 9 ¼” Front Press Axle (#49), two Ø ¾” Washers (#99), and two M10 Aircraft Nuts (#96). B.) Attach two Front Press Frames (#13) onto the bracket on the Front Press Base. Secure them to the Front Press Base with four M10 x 2 ½” Carriage Bolts (#85), Ø ¾” Washers (#99), and M10 Aircraft Nuts (#96). C.) Securely tighten all Nuts and Bolts previously installed. DIAGRAM 6
ページ14に含まれる内容の要旨
STEP 7 (See Diagram 7) A.) Attach the Butterfly Support Frame (#11) to the front of Right Vertical Frame (#3). Attach the Butterfly Pulley Support (#12) to the back of Right Vertical Frame. Align the holes and secure them with two M10 x 2 ½” Carriage Bolts (#85), Ø ¾” Washers (#99), and M10 Aircraft Nuts (#96). B.) Attach two Swivel Pulley Brackets (#23) to the Butterfly Pulley Support (#12). Secure each Bracket with one M12 x 4 3/8” Hex Bolt (#88), two Ø1” Washers (#100), and one M1
ページ15に含まれる内容の要旨
STEP 8 (See Diagram 8) A.) Attach the Vertical Press Frame (#20) to the Rear Vertical Frame (#4). Secure it with one M10 x 4 7/8” Vertical Press Axle (#48), two Ø ¾” Washers (#99), and two M10 x 5/8” Allen Bolts (#80). B.) Place the Vertical Press Frame rest against the rubber bumper on the Left Vertical Beam (#5). DIAGRAM 8 14
ページ16に含まれる内容の要旨
CABLE LOOP DIAGRAM 15
ページ17に含まれる内容の要旨
STEP 9 (See Cable Loop Diagram & Diagram 9) A.) Attach the 108” Upper Cable (#37) to the front opening on the Upper Frame (#6). Attach a Pulley (#56) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#83), two Pulley Bushings (#55), and one M10 Aircraft Nut (#96). Draw the Cable towards the back of the machine. Note: Make sure the Ball Stopper is underneath the frame. B.) Attach a Pulley to the bracket on the Upper Frame. Secure it with one M10x1 ¾” Allen Bolt (#82), two ∅¾”
ページ18に含まれる内容の要旨
STEP 10 (See Cable Loop Diagram & Diagram 10) A.) Clip one end of the 106” Butterfly Cable (#38) to the slot on the Left Butterfly Adjustment Frame. Draw the Cable through the slot then to the open left Swivel Pulley Bracket (#23). B.) Attach a Pulley (#56) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#82), two ∅ ¾” Washers (#99), and one M10 Aircraft Nut (#96). C.) Draw the Cable around the Pulley then downward. Install a Pulley to the Angled Double Floating Pulley Bracke
ページ19に含まれる内容の要旨
STEP 11 (See Cable Loop Diagram & Diagram 11) A.) Attach the 239” Front Press Cable (#36) to the lower opening on the Leg Developer (#19). Attach a Pulley (#56) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#83), two Pulley Bushings (#55), and one M10 Aircraft Nut (#96). B.) Draw the Cable underneath the Pulley to the opening on the bottom of Right Seat Support (#7). Attach a Pulley to the opening and secure it with one M10 x 1 ¾” Allen Bolt (#82), two Ø ¾” Washers (
ページ20に含まれる内容の要旨
DIAGRAM 11 19
