ページ1に含まれる内容の要旨
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
MARCY CORNER GYM
Safety Notice
CR 5
Hardware Identifier
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MWB CR 5
Retain This
Manual for
Reference
9-20-02
OWNER'S
IMPEX FITNESS PRODUCTS
MANUAL
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitnes
ページ2に含まれる内容の要旨
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE IDENTIFIER.....…....................................................................... 3 ASSEMBLY INSTRUCTIONS...............................................................…..........4 PARTS LIST…………………………………………………………….……….…….23 RESISTANCE CHART…………………
ページ3に含まれる内容の要旨
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person a
ページ4に含まれる内容の要旨
3
ページ5に含まれる内容の要旨
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Place the Right Base Frame (#46) and Left Base Frame (#87) on the floor, at a right angle to each other. Attach the Rear Vertical Beam (#50) to the joint and align the holes. Secure the holes with two M10 x 3” Carriage Bolts (#64), ∅ 3/4” Washers (#6) an
ページ6に含まれる内容の要旨
STEP 2 (See Diagram 2) A.) Attach the Right Vertical Beam (#21) to the Right Base Frame (#46). Secure it with two M10 x 2 ¾” Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft Nuts (#5). B.) Attach the Right Seat Support (#49) to the Right Vertical Beam (#21). Secure it with one Bracket (#7), two M10 x 2 ¾” Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft Nuts (#5). C.) Attach the other end of Right Seat Support (#49) to the Right Base Frame (#46). Secure it with on
ページ7に含まれる内容の要旨
STEP 3 (See Diagram 3) A.) Slide two ∅ 2 ½” Rubber Bumpers (#58) onto two Chromed Guide Rods (#58). Insert the two Guide Rods into the holes on the Right Base Frame (#46). Slide the Selector Stem (#67) onto the two Guide Rods (#22). Slide the Selector Stem over the Selector Rod (#69). Secure the Selector Rod to the Selector Stem with two M10 x 1” Allen Bolts (#56). DO NOT install the plates yet. B.) Repeat the Procedure A above to install another set of Guide Rods. C.) Place the Up
ページ8に含まれる内容の要旨
DIAGRAM 3 7
ページ9に含まれる内容の要旨
STEP 4 (See Diagram 4) A.) Attach the Front Press Base (#97) to the Right Base Frame (#46). Secure it with a 9 ¼” Front Press Axle (#60), two ∅ ¾” Washers (#6), and two M10 Aircraft Nuts (#5). B.) Attach the Front Press Frames (#63) to the Front Press Base. Secure it with four M10 x 2 ¾” Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft Nuts (#5). DIAGRAM 4 8
ページ10に含まれる内容の要旨
STEP 5 (See Diagram 5) A.) Attach the Butterfly Support Frame (#18) to the front of Right Vertical Beam (#21). Attach the Butter Pulley Support (#74) to the back of Right Vertical Beam. Align the holes. Secure them together with two M10 x 2 ¾” Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft Nuts (#5). B.) Insert the Axle on the Left Butterfly (#20) into the hole on the Butterfly Support Frame from the bottom. Secure it with one ∅ 1 ½” Washer (#16), ∅1 3/8” Lock Ring (#13), M6
ページ11に含まれる内容の要旨
STEP 6 (See Diagram 6) A.) Attach the Vertical Press Frame (#78) to the Rear Vertical Beam (#50). Secure it with a M10 x 4 7/8” Vertical Press Axle (#81), two ∅ ¾” Washers (#6), and two M10 x 1” Allen Bolts (#56). B.) Place the Vertical Press Frame rest onto the ∅ 1 ½” Rubber Bumper (#83). DIAGRAM 6 10
ページ12に含まれる内容の要旨
CABLE LOOP DIAGRAM 11
ページ13に含まれる内容の要旨
STEP 7 (Upper Cable Loop & Diagram 7) A.) Attach the 108” Upper Cable (#93) to the front opening on the Upper Frame (#8). Attach a Pulley (#79) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#10), two Pulley Bushings (#11), and one M10 Aircraft Nut (#5). Draw the Cable towards the back of the machine. Note: Make sure the Ball Stopper is underneath the frame. B.) Attach a Pulley to the bracket on the Upper Frame. Secure it with one M10 x 2” Allen Bolt (#98), two ∅ ¾” Washers
ページ14に含まれる内容の要旨
DIAGRAM 7 13
ページ15に含まれる内容の要旨
STEP 8 (See Butterfly Cable Loop & Diagram 8) A.) Attach the 83” Butterfly Cable (#95) to the slot on the back of Left Butterfly (#20). Draw the Cable through the slot then to the open left Swivel Pulley Bracket (#72). B.) Attach a Pulley (#79) to the bracket. Secure it with one M10 x 2” Allen Bolt (#98), two ∅ ¾” Washers (#6), and one M10 Aircraft Nut (#5). C.) Draw the Cable around the Pulley then downward. Install a Pulley to the Angled Double Floating Bracket (#51). Let the Bracke
ページ16に含まれる内容の要旨
DIAGRAM 8 15
ページ17に含まれる内容の要旨
STEP 9 (See Front Press Cable Loop & Diagram 9) A.) Attach the 247” Front Press Cable (#94) to the lower opening on the Leg Developer (#40). B.) Attach a Pulley (#79) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#10), two Pulley Bushings (#11), and one M10 Aircraft Nut (#5). C.) Draw the Cable underneath the Pulley through the opening on the Right Seat Support (#49) to the open bracket on the Right Base Frame (#46). D.) Attach a Pulley to the bracket. Secure it with one M1
ページ18に含まれる内容の要旨
DIAGRAM 9 17
ページ19に含まれる内容の要旨
STEP 10 (See Leg Press Cable Loop & Diagram 10) A.) Attach one end of the 82” Leg Press Cable (#96) to the open slot on the back of the Leg Press Frame (#84). Secure it with one M10 x 2 ½” Allen Bolt (#10), two ∅ ¾” Washers (#6), and one M10 Aircraft Nut (#5). B.) Draw the Cable to the front opening on the Left Seat Support (#92). Attach a Pulley to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#10), two Pulley Bushings (#11), and one M10 Aircraft Nut (#6). C.) Draw the Cable a
ページ20に含まれる内容の要旨
DIAGRAM 10 19
