ページ1に含まれる内容の要旨
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
COMPETITOR
Safety Notice
WM-205 COMBO BENCH
Hardware Identifier
Assembly Instruction
Exploded Diagram
Parts List
Warranty
Ordering Parts
Model
WM-205
Retain This
Manual for
Reference
07-03-08
OWNER'S
MANUAL
®
IMPEX INC.
14777 Don Julian Rd., City of Industry, CA 91746
Tel: (800) 999-8899 Fax (626) 961-9966
www.impex-fitness.com
info@
ページ2に含まれる内容の要旨
TABLE OF CONTENTS BEFORE YOU BEGIN............................................................................................... 1 IMPORTANT SAFETY NOTICE................................................................................ 2 HARDWARE PACK……............................................................................................ 4 ASSEMBLY INSTRUCTIONS.................................................................................... 5 EXPLODED DIAGRAM.............
ページ3に含まれる内容の要旨
PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machi
ページ4に含まれる内容の要旨
WARNING LABEL REPLACEMENT The Warning Label shown here has been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown. 3
ページ5に含まれる内容の要旨
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size. 4
ページ6に含まれる内容の要旨
ASSEMBLY INSTRUCTION Tools required assembling the machine: Two Adjustable Wrenches. NOTE: It is strongly recommended two or more people assembling this equipment to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the Left & Right Upright Beams (#1 & #19) by a Cross Brace (#2) in the mid-span. Secure them with two M10 x 2 ¾” Hex Bolts (#38), one Bracket (#16), two ∅ ¾” Washers (#44), and two M10 Aircraft Nuts (#47) on each end of the Cross Brace. B.) Insert the Backre
ページ7に含まれる内容の要旨
STEP 2 (See Diagram 2) A.) Connect the Front Stabilizer (#5) to the Main Seat Support (#3) and secure them with three M8 x 5/8” Hex Bolts (#41) and Ø 5/8” Washers (#45). DO NOT tighten the nuts and bolts yet. B.) Connect the Main Seat Support to the Cross Brace (#2). Secure it with two M10 x 2 1/8” Bolts (#39), one Bracket (#16), two ∅ ¾” Washers (#44), and two M10 Aircraft Nuts (#47). DO NOT tighten the nuts and bolts yet. C.) Connect one end of the Diagonal Support (#4) to the Main S
ページ8に含まれる内容の要旨
STEP 3 (See Diagram 3) A.) Attach the Leg Developer (#9) to the open bracket on the Front Stabilizer (#5). Secure it with one M10 x 2 ¾” Hex Bolt (#38), Ø ¾” Washer (#44), and M10 Aircraft Nut (#47). Do not over tighten the Nut and Bolt. Make sure the Leg Developer is able to swivel. B.) Insert two Foam Tubes (#10) halfway through the holes on the Leg Developer. Push four Foam Rolls (#35) onto the Tubes from both sides. C.) Attach a Spring Clip (#36) onto the weight post on the Le
ページ9に含まれる内容の要旨
7 STEP 4 (See Diagram 4) A.) Attach the Backrest Supports (#14) onto both ends of the Pivot on the Main Seat Support (#3). Place the other end rest against the Backrest Adjustment Bar (#8). B.) Place the Backrest Board (#17) onto the Backrest Supports. Secure it with four M6 x 1 ½” Hex Bolts (#43) and ∅ ½” Washers (#46). C.) Place the Seat Pad (#18) onto the bracket on the Main Seat Support (#3). Align the holes and secure it with four M6 x 1 ¼” Hex Bolts (#15) and ∅ ½” Washers (46)
ページ10に含まれる内容の要旨
8 STEP 5 (See Diagram 5) A.) Attach the ball end of the Cable (#33) to the Pulley (#30). Place the Pulley in the open slot on the Upper Lat Bar Frame (#52). Secure it with one M10 x 2” Hex Bolt (#40), two Pulley Bushings (#29), and one M10 Aircraft Nut (#47). B.) Slide the Weight Holder (#11) onto the Lat Bar Frame. C.) Insert the Lower Lat Bar Frame (#12) into the Upper Lat Bar Frame. Secure them together with four M8 x 5/8” Hex Bolts (#41) and four Ø 5/8” Washers (#45). D.) Connect t
ページ11に含まれる内容の要旨
9 10
ページ12に含まれる内容の要旨
PARTS LIST KEY NO. DESCRIPTION QUANTITY 1 Left Upright Beam 1 2 Cross Brace 1 3 Main Seat Support 1 4 Diagonal Support 1 5 Front Stabilizer 1 6 Right Bar Catch 1 7 Left Bar Catch 1 8 Backrest Adjustment Bar 1 9 Leg Developer 1 10 Foam Tube 2 11 Weight Holder 1 12 Lower Lat Bar Frame 1 13 Lat Bar 1 14 Backrest Support 2 15 M6 x 1 ¼” Hex Bolt 4 16 Bracket 3 17 Backrest Board 1 18 Seat Pad 1 19 Right Upright Beam 1 20 Weight Bar 1 21 2’ Square End Cap 2 22 1” x
ページ13に含まれる内容の要旨
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMP
