ページ1に含まれる内容の要旨
OWNER’S MANUAL
Bin Level
Automatic Control Grain Spreaders
Models 918 & 936
PNEG-1137
Date: 08-10-07
PNEG-1137
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Bin Level SAFETY GUIDELINES This manual contains information that is important for you, the owner/operator, to know and understand. This information relates to protecting personal safety and preventing equipment problems. It is the responsibility of the owner/operator to inform anyone operating or working in the area of this equipment of these safety guidlines.To help you recognize this information, we use the symbols that are defined below. Please read the manual and pay attention to these sect
ページ4に含まれる内容の要旨
Bin Level 1. Disconnect all power before servicing or adjusting. Have bin properly grounded. NOTE: With power on, the unit will start unexpectedly if the mercury switch is activated by jerking, shaking or jarring. 2. Do not enter a bin without proper eye protection while the unit is operating. 3. Do not attempt to service or adjust the unit from a ladder unless the ladder is secured to another piece of equipment or to the bin. The grain spreader can swing and will not support a ladder. Be sure
ページ5に含まれる内容の要旨
Bin Level Installation and Operation INSTALLATION Figure 1: 918 and 936 Bin Level - Hanger Hooks and Chains Double chains are attached to the hopper in three places. One chain from each of the three attachment points is hooked into a hanger hook to form a “V”. This is necessary to keep the spreader from swinging around the fill- hole each time the spreader is started. The Bin Level hanging height can change the spreading pattern. On steep-roofed bins, hanging the Bin Level lower in the bin
ページ6に含まれる内容の要旨
Installation and Operation Bin Level BIN LEVEL GRAIN SPREADER PARTS DRAWING FOR MODELS 918 & 936 6
ページ7に含まれる内容の要旨
Bin Level Parts List Bin Level Grain Spreader Parts List 918 936 Ref. Part No. Ref. Part No. No. Number Required Description No. Number Required Description 1 301A0102 2 Handle Nut 1 301A0102 2 Handle Nut 2 301A0108 1 Ring - Outside Pan 2 302A0309 1 Ring - Outside Pan 3 301A0110 1 Gate - Slide 3 301A0110 1 Gate - Slide 4 301A0111 1 Pan - Spreader, 18" O.D. 4 302A0307 1 Pan - Spreader, 20" O.D. 5 301A0122 1 Wheel - Rubber Drive, 2-3/4" 5 302A0313 1 Wheel - Rubber Drive, 3-1/4" 6 301B0202 1 Shield
ページ8に含まれる内容の要旨
Installation and Operation Bin Level 8
ページ9に含まれる内容の要旨
Bin Level TROUBLE SHOOTING PROBLEM CORRECTION (a) Spreader is not hung level. Grain is high on (b) Spreader not stopping & starting properly during filling. See Figure 2. one side of bin. (c) Spreader running continuously. (a) Slide Gate open too far. Grain is high at the (b) Spreader stopping too long, letting too much grain through slide gate. center of bin. See Figure 4. (c) Outside ring set too low. See Figure 3. (a) Slide Gate not open far enough. Grain is low at the (b) S
ページ10に含まれる内容の要旨
Bin Level NOTES 10
ページ11に含まれる内容の要旨
Bin Level The GSI Group, Inc. Warranty THE GSI GROUP, INC. (“GSI”) WARRANTS ALL PRODUCTS WHICH IT MANUFACTURES TO BE FREE OF DEFECTS IN MATERIAL AND WORKMANSHIP UNDER NORMAL USAGE AND CONDITIONS FOR A PERIOD OF 12 MONTHS AFTER RETAIL SALE TO THE ORIGINAL END USER. THE PURCHASER’S SOLE REMEDY AND GSI’S ONLY OBLIGATION SHALL BE TO REPAIR OR REPLACE, AT GSI’S OPTION AND EXPENSE, PRODUCTS THAT, IN GSI’S SOLE JUDGMENT, CONTAIN A MATERIAL DEFECT DUE TO MATERIALS OR WORKMANSHIP. ALL DELIVERY AND SHIPM
ページ12に含まれる内容の要旨
This Equipment shall be installed in accordance with the current installation codes and applicable regulations which should be carefully followed in all cases. Authorities having jurisdiction should be consulted before installation occurs. For more information, contact the DMC Distribution Center closest to you. Illiana Distribution Center Clear Lake Distribution Center 1004 E. Illinois St. 5205 4th Ave South Assumption, Illinois 62510 Clear Lake, Iowa 50428 Phone: 217-226-5100 Phone: 641-357-33
