ページ1に含まれる内容の要旨
Park bench with
solar liGhts
Model 95845
setuP and oPeration instructions
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
t o PreVent serious injury, read and understand
all warninGs and instructions before use.
© ®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of this manual
or any artwork contained herein may be
ページ2に含まれる内容の要旨
sPecifications Bench Dimensions 48” Long x 15-1/4” Deep x 14-1/4” High (Back Rest) 16” High from Ground Light Panels Qty. 6 “V” Design Crinkled Panels with LED Lighting Solar Panel Mount 9.33 Ft. Long Cord Batteries 3 Rechargeable “AA” 1.2V 500mAH (Included) Net Weight 31.1 Lbs. Maximum Weight Capacity 400 lb. save this Manual You will need the manual for the safety warnings and precautions, assembly instruc- tions, operating and maintenance procedures, parts list and diagram. Keep your invoic
ページ3に含まれる内容の要旨
7. do not allow children to play on this Park bench. Children under 10 years of age should be accompanied by an adult. Do not let children stand on this Park Bench. The Bench could topple if overloaded or if weight is distributed unevenly. 8. do not let children or animals near the power source of this product. 9. check for damaged parts. Before using this product, carefully check that it will oper- ate properly and perform its intended function. Check for damaged parts and any other condit
ページ4に含まれる内容の要旨
asseMbly We suggest you assemble the unit on a soft surface to avoid damage to the finish. 1 1 9, 8 & 10 9, 8 & 10 1 1 3 3 1 1 8, 9 &10 8, 9 &10 f fiiG Gure 1 ure 1 3 3 1. Attach the five wooden Seat Slats (3) onto the right and left Arm Rests (1) using the Screws (9) on the top side of the Slats and the Washers (8) and Nuts (10) on the underside. Hand tighten. See Figure 1. 3 5 7 7 & 8 fiGure 2 2. Attach the Seat Brace (5) to the wooden Seat Slats (3) using the Tap Screws (7).
ページ5に含まれる内容の要旨
Screw (6) Backrest (2) Armrest (1) fiGure 3 3. Attach the Back Assembly with LED Lights (2) to the Armrest (1), right and left. Use the four Screws (6) through the brackets on both Armrests (1) and through the Back Assembly (2). Tighten Screws. See Figure 3. 4. To secure the Bench to the ground, hammer the Ground Nails (9) through the pre-drilled holes at the base of each leg. Make sure that when hammering nails into ground that the area is clear of any underground wires or cables. Page 5 S
ページ6に含まれる内容の要旨
oPeratinG the Park bench Side Knob Solar Panel Stake fiGure 4 1. Place the Park Bench in a location where the sun can shine on the Solar Panel. Attach the Power Cord to the Solar Panel with Stake (4). Anchor or bury the Power Cord to avoid someone tripping over the wires. (Power Cord not shown above. See assembly drawing on page 8). See Figures 3 & 4. 2. Press the Solar Panel with Stake (4) into the Ground. Page 6 SKU 95845 for technical questions, please call 1-800-444-3353
ページ7に含まれる内容の要旨
Power Cord Leading to the Solar Panel with Stake (4) (not shown) fiGure 5 3. warning: avoid any electrical wires or cables hidden underground. 4. Use the two side knobs on the side of the Solar Panel (4) to tilt the Solar Panel to ab- sorb the suns rays for charging. See Figure 4 on page 5. 5. With the Cord from the back of the Park Bench connected to the Solar Panel with Stake (4), allow eight to twelve hours for the charge from the sun to take affect. 6. Have the Power Switch (11) that is
ページ8に含まれる内容の要旨
Parts list Part description Q’ty 1 Arm Rest (right/left) 2 2 Back Assembly with LED Lights and Cord 1 3 Wood Slat 5 (6) 4 Solar Panel with Stake 1 5 Seat Brace 2 (7) 6 Screw (6 X 15mm) 5 7 Tap Screw (5 X 15mm) 10 (8) 8 Washer 10 9 Screw (6 X 32mm) 10 (9) 10 Nut 10 11 Power Switch 1 (10) 12 Ground Nail 4 asseMbly dia GraM 9 8 10 6 12 6 2 6 6 11 3 5 4 1 7 note: Some parts are listed as shown for illustration purposes only and are not available individually as replacement parts. 07f Page 8 SKU 958
