ページ1に含まれる内容の要旨
COIL ROOFING NAILER
11 GAUGE
Model 92359
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
© ®
Copyright 2004 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For techn
ページ2に含まれる内容の要旨
Specifications In tem Descriptio 3 3 Fastener Length Capacity / " To 1- / " Long 4 4 Fs astener Gauge 0.12" Diameter Shank Md agazine Capacity 120-150 Per Loa OI perating PSI 65-120 PS SI CFM Required 7 SCFM @ 90 PS Tp rigger Type Full Sequential Safety Tri Accessories Carrying Case/ Hex Wrenches (3 mm, 4 mm, & 5 mm)/ Air Tool Oil/ ANSI Approved Safety Impact Eye Goggles/Nail Coil (7/8" Nails) Ns et Weight 11.2 Pound Save This Manual You will need this manual for the safety warnings and precauti
ページ3に含まれる内容の要旨
to do the work of a larger industrial tool. There are certain applications for which this tool was designed. It will do the job better and more safely at the rate for which it was intended. Do not modify this tool and do not use this tool for a pur- pose for which it was not intended. 6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically nonconductive clothes and nonskid foot wear are recommended when working. Wear restrict
ページ4に含まれる内容の要旨
aged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment and binding of moving parts; any broken parts or mounting fixtures; and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or re- placed by a qualified technician. Do not use the tool if the trigger does not oper- ate properly. 15. Guard against electric shock. Prevent body contact with grounded surfaces suc
ページ5に含まれる内容の要旨
other fasteners, or at too steep an angle. Fasteners can ricochet, causing per- sonal injury. Never fire the Nailer into the air, or point it toward yourself or another person. Always wear ANSI approved safety goggles during use, maintenance, and reloading. 24. Do not fire fasteners too close to the edge of a workpiece. They may split the workpiece and fly free, causing personal injury. 25. Take caution, as some woods contain preservatives such as copper chro- mium arsenate (CCA) which can b
ページ6に含まれる内容の要旨
Unpacking When unpacking, check to make sure all parts shown in the Parts List on page 13 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Operation For best service, you should incorporate an oiler, regulator, and inline filter, as shown in the diagram below. Hoses, couplers, oilers, regulators, and filters are all avail- able at Harbor Freight Tools. TO ROOFING NAILER Note: To connect this tool,
ページ7に含まれる内容の要旨
5. Connect the air supply to the tool at the Air Inlet (93). Set the regulator at the recommended 65 PSI to 120 PSI, and set not to go over the maximum 120 PSI. 6. Test the tool by depressing the nose against the workpiece without pulling the Trigger (47). The Tool must not cycle (fire). If it cycles (fires), stop immediately and have it repaired by a qualified service technician. 7. Hold the tool away or off of the workpiece. The nose of the tool should return to its original position. Sq
ページ8に含まれる内容の要旨
1. To open the Cannister (82), press down on the Shaft (68) and swing the Latch (64) and Cannister Cover (89) open. 2. Check the Adjuster Plate (86) inside the Cannister (82). The Platform can be 3 3 adjusted up and down to use various lengths of nails from / ” to 1- / ”: 4 4 A. Between 3/4” and 1” Long Nails (Use top setting). B. Between 1” and 1-1/4” Long Nails (Use middle setting). C. Between 1-1/4” and 1-3/4” Long Nails (Use bottom setting). SHAFT (68) CANNISTER COVER (89)
ページ9に含まれる内容の要旨
3. Place a coil of Nails (not included) around the Adjuster Plate (86) in the Nail Cannister (82). 4. Uncoil enough nails to reach the Feed Hook (50). Place the second nail on the coil between the teeth of the Feed Pawl, making sure the nail head fits in the slot in the upper portion of the Feed Pawl. 5. Swing the Cannister Cover (89) closed. Then, close the Latch (64). Make sure the Latch closes securely. If it does not engage, the nail head is not in the slot in the upper portion of the Fe
ページ10に含まれる内容の要旨
Trigger (47) once and one nail will fire. To fire another nail, pull the nose of the nailer up off the workpiece, place the nose back down onto the next position on the workpiece and briefly squeeze the trigger. Repeat this procedure to continue firing nails. Do not fire nails on top of one another or into any foreign object. Nails could bounce off, damaging the workpiece or causing PERSONAL INJURY. 3. Do not press the Nose of the Roofing Nailer against the work surface with excess force. Al
ページ11に含まれる内容の要旨
Anytime any maintenance or repairs are done (including clearing jams), FIRST: 1. Disconnect the Nailer from the air hose. 2. Attempt to fire the Nailer into a piece of scrap wood to ensure that it is discon- nected and is incapable of firing any nails. 3. Empty the Nail Cannister (82) completely. Clearing Jams 1. Occasionally a nail may become jammed in the firing mechanism of the Roofing Nailer, making the tool inoperable. 2. To remove a jammed nail, disconnect the Roofing Nailer from its
ページ12に含まれる内容の要旨
Anytime any maintenance or repairs are done, FIRST: 1. Disconnect the Nailer from the air hose. 2. Attempt to fire the Nailer into a piece of scrap wood to ensure that it is discon- nected and is incapable of firing any nails. 3. Empty the Nail Cannister (82) completely. Inspection, Maintenance, and Cleaning 1. Inspect the Nailer frequently and make sure that the tool is lubricated (manually or by an automatic oiling system) before each use with Pneumatic tool oil. Do not use detergent oil
ページ13に含まれる内容の要旨
PARTS LIST SKU 92359 For technical questions, please call 1-800-444-3353. PAGE 13
ページ14に含まれる内容の要旨
ASSEMBLY DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 92359 For technical questions, please call 1-800-444-3353. PAGE 14
