ページ1に含まれる内容の要旨
Laser Range Finder
Item 67802
INSTRUCTIONS AND
PRECAUTIONS
Visit our website at:
http://www.harborfreight.com
Read this material before using
this product. Failure to do so
can result in serious injury.
SAVE THIS MANUAL.
When unpacking, make sure that the
product is intact and undamaged.
If any parts are missing or broken,
please call 1‑800‑444‑3353
as soon as possible.
© ®
Copyright 2011 by Harbor Freight Tools . All rights reserved. No portion of this document
or any artwork contai
ページ2に含まれる内容の要旨
Specifications Important Safety Information Working Range 32′ 1. Never attach or use any other form of optical device with this product. Accuracy ±2% Use as intended only. Battery 1x 9V 2. Do not modify in any way as Product Label this may result in hazardous AVOID EXPOSURE radiation exposure. Laser light is emitted from this aperture. RANGE FINDER ITEM 67802 3. This product is not a toy. Do not allow children to play LASER LIGHT with or near this item. DO NOT STARE INTO BEAM Max. Outpu
ページ3に含まれる内容の要旨
Battery Installation / Replacement Before first use or if the Battery Indicator shows empty, then replace the battery: 1. Slide the Battery Cover down and off the back of the Meter. 2. Remove the old connected Battery. 3. Disconnect the old Battery. Dispose of it properly or recharge if rechargeable. 4. Reconnect new 9V Battery. It will properly attach only one way. 5. Insert connected Battery into compartment. 6. Slide the Battery Cover closed. SKU 67802 For technical questions, please
ページ4に含まれる内容の要旨
MEM INPUT MEM RECALL FT / M 1. Laser Opening: Components Laser light comes from this opening during use. Point away from eyes. 2. Sensor: This measures the location aimed at with the laser. 2 Do not cover during use. 1 3. Display: d b a c 3 e f Figure B: Display READ a. Area/Volume: Shows whether area or volume is being measured, and 4 what part is being measured (Length, Width, or Height). b. Addition: A + here means that the next measurement will be added to the curren
ページ5に含まれる内容の要旨
MEM INPUT MEM RECALL FT / M 4. Buttons: 5. Measurement Base: Rest this base against the surface a you want to measure from before taking a measurement. b e READ c f d g Figure C: Buttons a. Read: Takes a measurement. b. MEM Input: Stores current measurement to memory. c. MEM Recall: Displays stored measurement from memory, then clears it from memory. d. FT / M: Toggles between foot and meter units of measure. e. Volume calculation mode. f. Area calculation mode. g.
ページ6に含まれる内容の要旨
Addition Instructions Note: Addition can be used for distance, area, or volume Read the ENTIRE measurements. IMPORTANT SAFETY However, those measurements INFORMATION section are different units (for example, at the beginning of this feet, square feet, and cubic feet) document before set up and cannot be added together. or use of this product. 1. Take first measurement as explained under Distance Measurement “Distance Measurement”. 1. Place measurement base against 2. Press + / =
ページ7に含まれる内容の要旨
Memory Area/Volume Note: Memory can be used for Calculation distance, area, or volume Note: Area/volume calculation measurements. cannot be exited before 1. Press MEM INPUT to store calculation is complete. displayed Total Result in memory. 1. Press button to enter If only a Current Result is area calculation mode or displayed, it will be stored instead. press button to enter MEM will appear on Display. volume calculation mode. 2. Press MEM RECALL later to 2. The L will blink.
ページ8に含まれる内容の要旨
Record Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Replacement parts are not available for this item. 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
