ページ1に含まれる内容の要旨
1
/ ” CORDLESS DRILL
2
19.2 VOLT
94434
OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from that shown in this manual.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
© ®
Copyright 2006 by Harbor Freight Tools . All rights reserved. No portion
of this manual or any artwork contained herein may be reproduced in an
ページ2に含まれる内容の要旨
SPECIFICATIONS Battery Charger Input 120 VAC / 60 Hz Battery Type NiCd, 19.2 V, 1.7 Ah 1 Battery Charging Time 1 / Hours 2 Drill Specifications 0-350 RPM / 0-1,300 RPM; Variable Speed; Reversible; 24 Torque Settings; Pistol Grip; Squeeze Trigger Weight 5 lb. with Battery UNPACkING When unpacking, check to make sure all the parts shown on the Parts List on page 11 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manua
ページ3に含まれる内容の要旨
Electrical Safety 1. Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded. 2. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. Personal Safety 1. Stay alert. Watch what you are doing, and use common sense when operat- ing a power tool. Do not use a power tool while tired or under the influence of drugs,
ページ4に含まれる内容の要旨
3. Disconnect the power tool from its Battery Pack (22) before making any ad- justments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally. 4. Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. 5. Maintain tools with care. k eep cutting tools sharp and clean. Properly main- tained tools with a sharp cutting edge are less likely to bind and are
ページ5に含まれる内容の要旨
This is just an additional precaution; always check for hidden wiring before drilling. 5. Do not use the Cordless Drill or Charger (26) if it has been dropped, damaged, left outdoors, or immersed in liquid. 6. To avoid electrical shock, do not handle the Charger (26), its Power Cord Plug, or the Cordless Drill with wet hands. 7. k eep the Handle of the Cordless Drill dry, clean, and free from oil and grease. 8. Always turn off the Cordless Drill and unplug the Charger (26) from its electri-
ページ6に含まれる内容の要旨
chemicals are: lead from lead-based paints, crystalline silica from bricks and ce- ment or other masonry products, arsenic and chromium from chemically treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. (California Health & Safety C
ページ7に含まれる内容の要旨
(26) is unplugged from its electrical outlet prior to making any adjustments to the tool. (See Figure A.) 2. Chuck (11): Accepts up to 3/8” shank diameter Drill Bits (not included). To install a Drill Bit with the Cordless Drill pointed away from your body, hold the Chuck Sleeve firmly in place and turn the Chuck clockwise. Insert the shank of a Drill Bit all the way into the Chuck. While holding the Chuck Sleeve in place, turn the Chuck coun- terclockwise to lock the Drill Bit in place
ページ8に含まれる内容の要旨
5. NOTE: While charging, the Battery Pack (22) and Charger (26) may become warm to the touch. This is normal, and does not indicate a problem. (See Figure A.) 6. Once the Battery Pack (22) is fully charged, disconnect the Charger (26) from the electrical outlet. Then, disconnect the Charger from the Battery Pack. (See Figure A.) OPERATING INSTRUCTIONS 1. If possible, install the Side Handle (21) to allow better control of the drill. If desired, insert the Depth Gauge (25) through the h
ページ9に含まれる内容の要旨
8. Make sure to hold the Cordless Drill firmly with both hands, as torque from the Mo- tor will cause the tool to twist. FIGURE C FIGURE C T TOP OP VIEW VIEW S SPEED PEED S SELECT ELECTOR OR RED LIGHT RED LIGHT LEVEL LEVEL GREEN LIGHT GREEN LIGHT YELLO YELLOW LIGHT W LIGHT LIGHT LIGHT A ACTIV CTIVA AT TOR OR 9. Observe the top of the Cordless Drill. (See Figure C.) 10. The Cordless Drill is equipped with a Level that helps the operator drill holes parallel to the floor. (See Figure C.)
ページ10に含まれる内容の要旨
INSPECTION, MAINTENANCE, AND CLEANING 1. WARNING! Always turn the Trigger to its “OFF” position, unplug the Char- ger (26) from its electrical outlet, and disconnect the battery before performing any inspection, maintenance, or cleaning. 2. BEFORE EACH USE, inspect the general condition of the Cordless Drill. Check for misalignment or binding of moving parts, cracked or broken parts, leaking Battery Pack, damaged Charger wiring, chipped or broken Drill Bits, and any other condi- tion that m
ページ11に含まれる内容の要旨
PARTS LIST Part Description Qty. Part Description Qty. 1 Screw 8 15 Washer 1 2 Right Body 1 16 Panel 1 3 Plate 1 17 Transistor 1 4 Speed Control 1 18 Radiator 1 5 Level Tube 1 19 Trigger 1 6 Level Tube Panel 1 20 Battery Clamp 1 7 Screw 2 21 Side Handle 1 8 Display Panel 1 22 Battery Pack 1 9 Screw 2 23 Forward/Reverse Switch 1 10 Screw 1 24 Left Body 1 11 Chuck 1 25 Depth Gauge 1 12 Gear Box 1 26 Charger 1 13 Connector 1 27 Torque Selector Ring 1 14 Screw 1 PLEASE READ THE FOLLOWING CAREFULLY T
ページ12に含まれる内容の要旨
ASSEMBLY DIAGRAM 26 NOTE: Some parts are listed and shown for illustration purposes only, and are not avail- able individually as replacement parts. SKU 94434 For technical questions, please call 1-800-444-3353 PAGE 12
