ページ1に含まれる内容の要旨
MODEL H8235
3-PIECE FRAMING/BRAD/PALM
NAILER KIT
OWNER'S MANUAL
COPYRIGHT © SEPTEMBER, 2007 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#TS9832 PRINTED IN CHINA
ページ2に含まれる内容の要旨
����������������������������������������������������������������������� �������������������������������������������������������������� ���������������������������������������������������������������������� �������������������������������������������������������������������� ������������������������ ������������������������������������������������������������������ �������������������������������������������������������������������� ���������������������������������������������������������������
ページ3に含まれる内容の要旨
SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indica
ページ4に含まれる内容の要旨
Safety Instructions for Pneumatic Tools 10. USE PROPER AIR HOSE for 17. DISCONNECT TOOLS before the tool. Make sure your air hose servicing, changing accessories, or is in good condition and is long moving to another location. enough to reach your work without 18. DO NOT OVERREACH. Keep stretching. proper footing/balance at all times. 11. WEAR PROPER APPAREL. Do 19. USE THE RECOMMENDED not wear loose clothing, gloves, ACCESSORIES. Consult owner’s neckties, rings, bracelets, or other ma
ページ5に含まれる内容の要旨
Additional Safety Instructions for Nailers 1. HAND INJURIES: Do not place your 6. HOSE USAGE: Make sure your air hands near the nail point of entry. A hose is designed for the tool in use, is nail can deflect and tear through the in good condition, and is long enough surface of the workpiece, puncturing to reach your work without stretching. your hand or fingers. However, an overly long air hose in 2. COMBUSTIBLE GASES: Never con- the work area may be a tripping haz- nect the nailer to pres
ページ6に含まれる内容の要旨
Never point these nailers at yourself or another person! Always pay atten- tion to the direction these nailers are pointed. Use these tools with respect and caution to lessen the possibility of operator or bystander injury. Ignoring this warning may result in serious personal injury. Read the manual before operation. Become familiar with these nailers, their safety instructions, and their Nailer accidents routinely happen operation before beginning any work. while moving the gun to an
ページ7に含まれる内容の要旨
INTRODUCTION Foreword Tool Data Framing Nailer The specifications, details, and photo- graphs in this manual represent the Model 1 Nail Size ...................... ⁄8" Shank Diameter H8235 as supplied when the manual was Nail Strip Angle .................21º Round Head prepared. However, owing to Grizzly’s pol- Nail Length ......................................2"–3½" icy of continuous improvement, changes Magazine Capacity ........................ 60 Nails may be made at any time with no oblig
ページ8に含まれる内容の要旨
SET UP Unpacking Inventory Your new nailer kit was carefully pack- After you open the nailer case, you should aged for safe shipping. If you discover any find the following. damage after you have signed for deliv- ery, immediately call Customer Service at Model H8235 Inventory (Figure 1) Qty (570) 546-9663 for advice. A. 21° Framing Nailer ............................. 1 B. 18 Gauge Brad Nailer ........................ 1 Save the containers and all packing mate- C. Safety Goggles .............
ページ9に含まれる内容の要旨
Compressed Air System The Model H8235 is designed to be oper- ated at the following air pressures using clean, dry, regulated, compressed air: Nailer Operating Air Pressure Framing ................................... 80–100 PSI Brad ......................................... 60–100 PSI Palm ........................................ 70–100 PSI Exceeding the maximum permissible operating pressure may damage the DO NOT exceed the 120 PSI maximum nailers and cause them to malfunc- operating press
ページ10に含まれる内容の要旨
5. Without pressing the trigger, depress Safety Nose the safety nose mechanism against a Mechanism scrap piece of wood that is clean and free of any knots, nails, or other foreign objects. A safety mechanism on the nose of the framing and brad nailers protects against — If the nailer does not fire, then the accidental firing. When the trigger is safety nose mechanism is working pressed, the nailer will not fire until the correctly. safety nose mechanism is depressed. — If the nailer
ページ11に含まれる内容の要旨
OPERATIONS Loading When replacing nails in your Model H8235 framing and brad nailers follow these guidelines: Framing Nailer 1 Nail Size ...................... ⁄8" Shank Diameter Figure 4. Loading nails into the magazine. Nail Strip Angle .................21º Round Head 1 Length..............................................2"–3 ⁄2" 4. Tilt the nailer to slide the nails all the Magazine Capacity ........................ 60 Nails way down to the nose. To load your framing nailer: 5. With one h
ページ12に含まれる内容の要旨
3. Pull the magazine cover back until it 3. Depress the safety nose mechanism stops. against your workpiece. 4. Insert a strip of nails, pointed-end 4. Before pulling the trigger, make sure down, into the magazine as shown in your free hand and other body parts Figure 6. are positioned out of the way of a potential path of a nail in case of deflec- tion. Deflection is caused when grain irregularities, knots, or foreign objects inside the wood cause the nail to change its path, resultin
ページ13に含まれる内容の要旨
Palm Nailer Adjusting Framing 1. Connect the air supply to the quick con- Nailer Depth nect fitting. 2. Make sure your free hand and other Depending on the type of stock and nails body parts are positioned out of the you are using, it may be necessary to way of a potential path of a nail in case adjust the depth of nail penetration for your of deflection. framing nailer. 3. Hold the nail firmly in place with one To adjust the depth for your framing hand as if using a regular hammer. nai
ページ14に含まれる内容の要旨
Brad Nailer Clearing Jammed To clear a jammed nail from the dis- Nails charge area: 1. DISCONNECT NAILER FROM THE A jammed nail must be cleared before AIR SUPPLY! using the nailer again. 2. Depress the magazine latch and pull Framing Nailer the magazine cover back until it stops. To clear a jammed nail from the dis- 3. Remove the nail stick from the maga- charge area: zine. 1. DISCONNECT NAILER FROM THE 4. Remove the two cap screws and driver AIR SUPPLY! guide cover from the nose assemb
ページ15に含まれる内容の要旨
Framing & Brad Nailer Replacing Pistons/ To replace a piston for your framing or O-Rings brad nailer: 1. DISCONNECT NAILER FROM THE Under heavy use, a piston, piston shaft, AIR SUPPLY! or O-ring may wear out. Replacement is quick and easy. Contact Grizzly Customer 2. Remove all nails from the magazine Service at (800) 523-4777 to obtain the fol- cartridge, and clean the exterior of the lowing Piston Repair Kits or the Complete nailer. O-Ring Repair Kits. 3. Remove the four cap screws on
ページ16に含まれる内容の要旨
8. Apply a thin film of tool oil on the new 5. Grab the ram pin and pull the piston O-ring and place it on the new piston. from the cylinder. 9. Insert the new piston in the cylinder. 6. Apply a thin film of tool oil on the new Make sure that the grooves on the pis- O-ring and place it on the new piston. ton shaft line up with those on the guide at the bottom of the cylinder. The new 7. Insert the new piston into the cylinder. piston should easily slide into the cyl- The new piston should e
ページ17に含まれる内容の要旨
CLEANING & LUBRICATION Cleaning Lubricating Use non-flammable solvent to clean the Standard pneumatic tool oil has been nose assembly of the nailer. Always be included with your new Grizzly nailer to sure that the nailer is dry before using it help maintain its useful life. Place two to again. six drops of oil in the nailer air inlet (as shown in Figure 15) before every use, or Do not allow dust, chips, sand, etc. into after 2 hours of continuous use. the air connectors or into the body o
ページ18に含まれる内容の要旨
H8235 PARTS Framing Nailer Parts Breakdown �� �� �� �� � �� �� �� �� �� �� � �� �� �� �� �� �� � �� �� �� �� �� � �� �� �� � �� �� �� � �� �� � � �� �� �� �� �� � �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� -16- Model H8235 3-Piece Framing/Brad/Palm Nailer Kit
ページ19に含まれる内容の要旨
Framing Nailer Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PSB11M CAP SCREW M8-1.25 X 16 49 PH7665049 DEPTH ADJUSTMENT NUT 2 PH7665002 EXHAUST PORT 50 PH7665050 COPPER COLLAR 3 PH7665003 RUBBER SPACER 51 PH7665051 SAFETY NOSE CASE 4 PH7665004 COMPRESSION SPRING 52 PORS060 O-RING 59.5 X 2.0 S60 5 PH7665005 SPRING WIRE 53 PH7665053 DRIVE GUIDE 6 PSB06M CAP SCREW M6-1 X 25 54 PLW04M LOCK WASHER 8MM 7 PLW03M LOCK WASHER 6MM 55 PSB13M CAP SCREW M8-1.25 X 30 8 PH7665008 CYLINDER PLUG 56
ページ20に含まれる内容の要旨
Brad Nailer Parts Breakdown -18- Model H8235 3-Piece Framing/Brad/Palm Nailer Kit ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ���
