ページ1に含まれる内容の要旨
ROUND HEAD FRAMING
NAILER KIT
MODEL G6050
INSTRUCTION MANUAL
COPYRIGHT © MAY, 2002 BY GRIZZLY INDUSTRIAL, INC.
1821 VALENCIA ST., BELLINGHAM, WA 98227
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN TAIWAN
ONLINE MANUAL DISCLAIMER
THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS CUR-
RENTLY BEING SHIPPED. THE MACHINE CONFIGURATION CAN CHANGE AS PRODUCT IMPROVEMENTS
AR
ページ2に含まれる内容の要旨
SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progres- sion of symbols is described below. Remember that safety messages by them- selves do not eliminate danger and are not a substitute for proper accident pre- vention measures. Indica
ページ3に含まれる内容の要旨
Safety Instructions For Pneumatic Tools 10. USE PROPER AIR HOSE for the 18. DISCONNECT TOOLS before ser- tool. Make sure your air hose is in vicing and changing accessories. good condition and is long enough to 19. USE THE RECOMMENDED reach your work without stretching. ACCESSORIES. Consult the owner’s manual for recommended 11. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neck- accessories. The use of improper ties, rings, bracelets, or other jewel- accessories may cause risk of ry
ページ4に含まれる内容の要旨
Basic Nailer Safety In addition to the rules stated in the previ- ous section, and those in the warning boxes throughout this manual, please observe the following safety tips for your new nailer: 1. READ THIS ENTIRE MANUAL BEFORE OPERATING THE NAIL- ER. 2. ALWAYS DISCONNECT AIR FROM THE NAILER whenever servicing or Operating this nailer can propel installing nails. During maintenance, objects into the air, causing immedi- a nailer connected to air may fire acci- ate eye damage. To protect yourse
ページ5に含まれる内容の要旨
INTRODUCTION Most important, we stand behind our tools. Commentary If you have any service questions or parts We are proud to offer the Grizzly Model requests, please call or write us at the G6050 Round Head Framing Nailer. This location listed below. model is part of a growing Grizzly family of fine power tools. When used according to Grizzly Industrial, Inc. the guidelines set forth in this manual, you 1203 Lycoming Mall Circle can expect years of trouble-free, enjoy- Muncy, PA 17756 able oper
ページ6に含まれる内容の要旨
Compressed Air System Safety Yoke Mechanism The Model G6050 is designed to be oper- A safety yoke mechanism (bump fire) on ated at 80-120 psi. Do not exceed the the nose of the nailer acts as a safety maximum operating pressure! device. When the trigger is pressed, the nailer will not fire until the safety yoke Before you use your new nailer, regulate mechanism is depressed. the air pressure on your air compressor to barely over the minimum psi for your nail- Before you use your nailer for the f
ページ7に含まれる内容の要旨
OPERATION Single/Bump Fire Mode Loading Nailer The Model G6050 is equipped with a sin- To load your nailer: gle/bump fire trigger. 1. Disconnect the air supply from the To select single or bump fire operation: nailer! 2. Pull the magazine pusher all the way 1. Disconnect the air supply from the back until it locks in place. nailer! 3. Place a stick of nails into the maga- 2. Locate the hex nut that secures the zine as shown in Figure 1. Make sure safety yoke mechanism to the trigger the pointed
ページ8に含まれる内容の要旨
Besides damaging your workpiece, Operating Nailer deflection can cause injury if your free If you have not read the safety instruc- hand is securing the workpiece in the tions in this manual, do not operate the location that the nail deflects. nailer. 4. Press the trigger. If the nail drove into the wood far enough, continue with Periodically, place one drop of the included your intended operations. If the nail oil into the quick connect fitting where the either went too far or not far enough, n
ページ9に含まれる内容の要旨
To clear a jammed nail from the discharge Clearing Jammed Nails area with the Model G6050: The most frequent situation with any type of nailer is a nail jam. A jammed nail must 1. Disconnect the nailer from the air be cleared before using the nailer again. supply! The two places where a nail can get 2. Pull the magazine pusher all the way jammed are the magazine and the dis- back until it locks in place. charge area. 3. Remove all nails from the magazine. 4. Locate the nail inside of the nailer
ページ10に含まれる内容の要旨
Oiling Nailer Cleaning Nailer The Model G6050 is considered an oil-less Use a good solvent to clean the nose assembly of the nailer. Always be sure that model. This means it features a teflon pis- the nailer is dry before using it again. ton ring that does not require oil to operate. However, periodic applications of oil will Do not allow dust, chips, sand, etc. into the extend the useful life of the piston assem- air connectors or into the body of the nail- bly. er; this may result in leaks an
ページ11に含まれる内容の要旨
Replacing Pistons/O-Rings If you use your nailer day in and day out, Grizzly offers repair pistons as cheap insurance against wasted down time and lost profits in the event that a piston or pis- ton shaft becomes worn out. To replace a piston: Figure 7. Removing nailer exhaust cap. 8. With a long flathead screwdriver or similarly shaped tool, push the piston shaft back inside the nailer until you can grip the piston head and remove it from the cylinder. (Be careful not to scratch the discharge a
ページ12に含まれる内容の要旨
G6050 PART BREAKDOWN -11- G6050 Round Head Framing Nailer Kit 15A 15-2 16B 1A 7A 2A 4 5A 89 6 30A 28A 8 82 20 9 24 10 80A 21A 11 83A 29 41 25 73 43 39 42 12 26 44 82 38A 13 74A 45 59 19 33 32 46 14 36 47 22 27 39 34 88 48 39 49 28A 57 64 69 23 30A 50 60A 58 95 63 51 56 56 62 84 52 40 67A 71A 68A 39 66 85 39 35A 92 90 65 85 31A 78 61A 77 76 12-1 21-1 37A 53A
ページ13に含まれる内容の要旨
REF PART # DESCRIPTION REF PART # DESCRIPTION 01A P6048007A BUTTON HD CAP SCR 42 P6050042 PLUNGER 02A P6050002A EXHAUST COVER 43 P6050043 VALVE 04 P6050004 PU WASHER 44 P6050044 O-RING 05A P6050005A CAP SCREW + SW 45 P6048045 O-RING 06 P6050006 CAP 46 P6050046 O-RING 07A P6044077 FLAT WASHER 47 P6044047 VALVE PLUNGER 08 P6050008 SPACER 48 P6050048 O-RING 09 P6050009 PISTON STOPPER 49 P6048049 SPRING 10 P6050010 SPRING 50 P6050050 PLUNGER 11 P6050011 O-RING 51 P6050051 O-RING 12 P6050012 PISTON H
ページ14に含まれる内容の要旨
TROUBLESHOOTING PROBLEM CAUSE ACTION Air leaking at trigger valve 1. O-rings in trigger valve 1. O-rings must be replaced housing are damaged. & operation of safety area. yoke must be checked. Air leaking between hous- 1. Loose screws in housing. 1. Tighten screws. ing and hose. 2. Damaged O-ring. 2. Replace O-ring. 3. Loose air fitting. 3. Tighten air fitting. Air leaking between hous- 1. Damaged seal. 1. Replace damaged seals. ing and cap assembly. 1. Air leaks. 1. Tighten screws and fit- Tool
ページ15に含まれる内容の要旨
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance. This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are here- by limited to
ページ16に含まれる内容の要旨
WARRANTY CARD Name__________________________________________________________ Street__________________________________________________________ City____________________State________Zip_________ Phone Number____________E-Mail___________________FAX____________ Model #_______________Serial#________________Order #______________ The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of course, all information is s
ページ17に含まれる内容の要旨
Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT NAIL
