ページ1に含まれる内容の要旨
MODEL G0733
18" X 47" WOOD LATHE
OWNER'S MANUAL
(For models manufactured since 10/11)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
ページ2に含まれる内容の要旨
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use. This responsibility includes but is not limited to
ページ3に含まれる内容の要旨
Table of Contents INTRODUCTION ............................................... 2 SECTION 1: SAFETY ....................................... 7 SECTION 2: POWER SUPPLY ...................... 10 SECTION 5: ACCESSORIES ......................... 33 SECTION 6: MAINTENANCE ......................... 36 SECTION 3: SETUP ....................................... 12
ページ4に含まれる内容の要旨
INTRODUCTION Manual Accuracy Contact Info your machine may not exactly match the manual Machine Description www.grizzly.com
ページ5に含まれる内容の要旨
Identification Figure 1. To reduce the risk of serious injury when using this machine, read and understand this entire manual before beginning any operations.
ページ6に含まれる内容の要旨
Glossary Of Terms VERY Bed: Outboard Turning: Chuck: Roughing Out: Faceplate: Spindle: Faceplate Turning: Spindle-Turning: Backing Block: Swing: Headstock: Tailstock:
ページ7に含まれる内容の要旨
Machine Data Sheet Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901
Weight.............................................................................................................................................................. 419 lbs. Width (side-to-side) x Depth (front-to-back) x Height.................................................... 80-3/4 x 19-1/16 x 48-1/16 in. Footprint (L
ページ8に含まれる内容の要旨
Spindle Taper............................................................................................................................................ MT#2 Spindle Size...................................................................................................................... 1-1/4 x 8 (RH) TPI in. Spindle Bore......................................................................................................................................... 0.393 in. Spindle Center............
ページ9に含まれる内容の要旨
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of impor- tance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indica
ページ10に含まれる内容の要旨
DISCONNECTING POWER SUPPLY. GUARDS & COVERS. NEVER STAND ON MACHINE. APPROVED OPERATION. STABLE MACHINE. DANGEROUS ENVIRONMENTS. AWKWARD POSITIONS. ONLY USE AS INTENDED. UNATTENDED OPERATION. OFF USE RECOMMENDED ACCESSORIES. MAINTAIN WITH CARE.
ページ11に含まれる内容の要旨
Additional Safety for Wood Lathes KEEPING GUARDS IN PLACE. WORKPIECE CONDITION. EYE/FACE PROTECTION. ADJUSTMENTS/MAINTENANCE. OFF RESPIRATORY PROTECTION. STOPPING LATHE. MOUNTING WORKPIECE. AVOIDING ENTANGLEMENT. ADJUSTING TOOL REST. FACEPLATE TURNING. ON TURNING SP
ページ12に含まれる内容の要旨
SECTION 2: POWER SUPPLY Availability Circuit Information For your own safety and protection of property, consult an electrician if you are Electrocution, fire, or unsure about wiring practices or electrical equipment damage may codes in your area. occur if machine is not correctly grounded and Note: The circuit requirements listed in this man- connected to the power ual apply t
ページ13に含まれる内容の要旨
Grounding Requirements For 220V operation: GROUNDED 6-15 RECEPTACLE Extension Cords 6-15 PLUG Figure 2. Minimum Gauge Size ...........................14 AWG Maximum
ページ14に含まれる内容の要旨
SECTION 3: SETUP Needed for Setup This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with Description Qty the controls and opera- tions before starting the machine! Wear safety glasses dur- ing the entire setup pro- Unpacking cess! The G0733 and its com- ponents are very heavy. please call us immediately Get lifting help or use at (570) 546-9663 for advic
ページ15に含まれる内容の要旨
Inventory Inventory Inventory: (Figures 3–6) Qty A. B. Figure 4. C. D. E. F. G. H. I. J. K. Figure 5. Figure 3. NOTICE Figure 6. Some hardware/fasteners on the inventory list may arrive pre-installed. Check mount- ing locations before assuming that any items from
ページ16に含まれる内容の要旨
Site Considerations Weight Load Physical Environment Machine Data Sheet Space Allocation Electrical Installation See below for required space allocation. Lighting Children or untrained people may be seriously injured by this machine. Only install in an access restricted lo
ページ17に含まれる内容の要旨
Cleanup Mounting Bolting to Concrete Floors Figure 8 Before cleaning, gather the following: Basic steps for removing rust preventative: 1. 2. 3. Figure 8 4. Steps 2–3 NOTICE An
ページ18に含まれる内容の要旨
4. Assembly Step 7 OPERATIONS Page 19, The G0733 and its com- 5. ponents are very heavy. Get lifting help or use power lifting equipment Figure 11 such as a forklift to move heavy items. To assemble your lathe: 1. Figure 9 Figure 11. 6. Figure 12 Figure 9. Steps 5–6 2. 3. Figure 10 Figure 12. Figure 10.
ページ19に含まれる内容の要旨
7. Power Connection Connecting Power 1. OFF 8. 2. Figure 13 Figure 13. Figure 15. Connecting power. Disconnecting Power 9. 1. OFF 2. Figure 14 Figure 16. Disconnecting power. Figure 14.
ページ20に含まれる内容の要旨
6. Test Run Troubleshooting Page 37 7. 8. Before starting the lathe, make sure you have performed the preceding assembly and adjustment instructions, and you have read through the rest of the manual and are familiar with the various functions and 9. safety features on this machine. Failure to follow t
