ページ1に含まれる内容の要旨
CORDLESS
DRILL
443T, 243T, 183T,
GTX12100K, GTX144100K
INSTRUCTION MANUAL
1
ページ2に含まれる内容の要旨
Contents Warranty 2 � � � � � � � � � � � � � � � � � � � � Description of symbols 3 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � Specifications 4 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � Safety instructions 4 � � � � � � � � � � � � � � � � � � � � �
ページ3に含まれる内容の要旨
Description of symbols Introduction The rating plate on your tool may show symbols. These Your new GMC power tool will more than satisfy your represent important information about the product or expectations. It has been manufactured under stringent instructions on its use. GMC Quality Standards to meet superior performance criteria. Wear hearing protection. Wear eye protection. You will find your new tool easy and safe to operate, Wear breathing protection. and, with proper care, it w
ページ4に含まれる内容の要旨
ページ5に含まれる内容の要旨
shoes, hard hat, or hearing protection used for before use. Many accidents are caused by poorly appropriate conditions will reduce personal injuries. maintained power tools. c. Avoid accidental starting. Ensure the switch is in the f. Keep cutting tools sharp and clean. Properly off position before plugging in. Carrying power tools with maintained cutting tools with sharp cutting edges are your finger on the switch or plugging in power tools that less likely to bind and are easier to control.
ページ6に含まれる内容の要旨
be considered a case of misuse. The user and not the Additional safety instructions for drills manufacturer shall be liable for any damage or injury Wear ear protectors with impact drills. resulting from such cases of misuse. Exposure to noise can cause hearing loss. To use this tool properly, you must observe the safety Use auxiliary handles supplied with the tool. regulations, the assembly instructions and the operating Loss of control can cause personal injury. instructions to be found
ページ7に含まれる内容の要旨
charging the exact type of rechargeable battery pack as • I f you wish to charge a second battery pack, unplug supplied with the charger.Any other use may result in the charger from the mains supply and leave it for at the risk of fire, electric shock or electrocution. least 15 minutes. After this time you can charge a second battery pack. • The charger and battery packs supplied with it are specifically designed to work together. Do not attempt Additional safety instructions for the to c
ページ8に含まれる内容の要旨
Know your product 6 This drill is mainly used for drilling in wood or metal sheet and 5 screwdriving. Use the tool and accessories only for intended applications. All other applications are expressly ruled out. 1. Keyless chuck 1 2. Torque collar 2 3. Trigger with variable speed control 4. Forward/reverse switch 5. Side handle 4 6. Side handle clamp knob 3 7. Battery pack release tabs 8. R echargeable battery pack 9. Slim line adaptor 10. Charger 11. LED Lights 12. Battery indicator
ページ9に含まれる内容の要旨
3. Plug in the charger and switch Unpacking on. The red LED indicator will Due to modern mass production techniques, it is unlikely show power to the adaptor and that your GMC Power Tool is faulty or that a part is that charging is missing. If you find anything wrong, do not operate the taking place. tool until the parts have been replaced or the fault has 4. The battery charging time is been rectified. Failure to do so could result in serious approximately 3–5 hours. The personal i
ページ10に含まれる内容の要旨
battery indicator is showing only 1 LED (low) the battery Drilling uses the forward mode. The reverse mode is should be removed and put on the charger. intended for the removal of screws. LED Work area light Adjustable torque The drill has 3 LED lights (11) This drill is equipped with 20 to illuminate the work area and torque settings plus one drill improve vision when drilling in setting which are controlled areas with insufficient light. by the torque collar (2). By rotating the collar
ページ11に含まれる内容の要旨
tighten on the drill bit. The front section of the chuck Drilling masonry needs to be tightened firmly to ensure the drill bit is • This drill is not designed for drilling masonry. Purchase held securely. or hire a Hammer drill. 4. To remove the drill bit, hold the rear section of the Drilling wood chuck firmly and rotate sharply the front section of the • Clamp a piece of scrap wood to the back of your work to chuck in a anti-clockwise direction, sufficiently enough prevent splintering. t
ページ12に含まれる内容の要旨
GMC customer assist If your product needs repairing, replacing, technical service or you simply need help or advice, please contact us on our Customer Assist Line 1300 880 001 (Australia) or 0800 445 721 (New Zealand). For prompt service we suggest you log your service request online at www.gmcservice.com.au. Should you not have access to the Internet, please contact our service department on 1300 880 001 (Australia) or 0800 445 721 (New Zealand). 7am –7pm, 7days a week (AEST). Please n
