ページ1に含まれる内容の要旨
TROUBLESHOOTING
Before seeking repair or replacement, we recommend that you review the following:
LOUD NOISES: (Other than those during grinding of IF TURNTABLE DOES NOT ROTATE FREELY:
small bones and fruit pits): These are usually caused by Turn off disposer, then check for any foreign object lodged
accidental entry of a spoon, bottle cap or other foreign between the turntable and grind ring. Dislodge object by
object. To correct this, turn off electrical switch and water. rotating table wit
ページ2に含まれる内容の要旨
(July 2011) All about the Use& Care of your Food Waste Disposer TA B L E O F C O N T E N T S Product Registration........................................... 2 Electrical Connections ........................................ 6 Important Safety Instructions .............................. 2 Operating Instructions ........................................ 7 Removal of Old Unit ........................................... 3 Troubleshooting................................................. 8 Installation
ページ3に含まれる内容の要旨
PRODUCT REGISTRATION Bill of sale, sales slip, cancelled check or other purchase See insert for specific information about your new record should be kept to verify the original purchase date for disposer: warranty purposes. NOTE: This Food Waste Disposer has been designed to operate on 110-120 Volt, 60Hz exclusively. Using any other voltage or Hz adversely affects performance. Model Number* IMPORTANT: Read all instructions thoroughly. Keep this guide for future reference. Serial Number* C
ページ4に含まれる内容の要旨
REMOVAL OF OLD UNIT TYPICAL INSTRUCTIONS, YOUR MODEL MAY VARY Caution: Be sure to support the disposer while Before starting this step, turn off electrical power perfomring this step or it may fall when the at the circuit breaker or fuse box. mounting ring is disconnected from the mounting If your old mount is the same as the mount on your new assembly. If your disposer is hard wired (metal disposer, just reverse the assembly instructions found in shielded cable not utili
ページ5に含まれる内容の要旨
INSTALLATION OF MOUNTING ASSEMBLY G Stopper Rubber Gasket A Sink Flange B H Lower Mounting Ring Fiber Gasket C Backup Flange D Dishwasher Inlet Mounting Ring E Disposer Hush Cushion® Snap Ring F NOTE: Hush Cushion included between mounting ring and lower mounting ring. Mount System READ COMPLETELY BEFORE STARTING NOTE: Pay close attention to the order of mount assembly parts, as they have been correctly assembled by the factory. E. Tighten the 3 mounting screws evenly with a A. Di
ページ6に含まれる内容の要旨
INSTALLATION OF MOUNTING ASSEMBLY YOUR DISPOSER COMES WITH THE FOLLOWING MOUNT SYSTEM 1 6 2 1 1 3 4 5 A B C D E Mount System READ COMPLETELY BEFORE STARTING NOTE: Pay close attention to the order of mount assembly parts, as they have been correctly assembled by the factory. D. Place a weight such as a disposer on the sink flange to A. Evenly apply 1/2” thick rope of plumber’s putty around hold it in place. Use a towel to prevent scratching sink. flange (1). Pull snap ring
ページ7に含まれる内容の要旨
ELECTRICAL CONNECTIONS Wiring Disposer Directly to House Current A. Connect disposer to 110-120 Volt, 60Hz AC current only. This appliance must be connected to a grounded, metal permanent wiring system or an equipment grounding con- B. If plug-in cord is used, use a three prong plub (see A). ductor must be run with the circuit conductors and connected Ground wire should be attached to the ground screw in to the equipment-grounding terminator or lead on the the bottom of the end bell (see
ページ8に含まれる内容の要旨
OPERATING INSTRUCTIONS The Anti-Jam Swivell Impellers make a clicking sound as they swing into place. This indicates normal operation. that the disposer slows down while grinding. The A. Remove sink stopper. Turn on a medium flow of cold disposer is actually increasing torque (grinding power) water. and is operating under normal conditions. B. Turn switch to ON position; your motor is turning at full D. Before turning disposer off, let water and disposer run speed and ready to use. f
