ページ1に含まれる内容の要旨
Product features and decorations may vary from picture above.
Instructions
Model Number: H4792
WARNING
IMPORTANT! KEEP INSTRUCTIONS FOR FUTURE REFERENCE.
Please read these instructions before use of this product.
Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included).
Requires four LR20 ("D") alkaline batteries (not included) for operation.
www.fisher-price.com
1
ページ2に含まれる内容の要旨
Parts IMPORTANT! Please remove all parts from the package and WARNING identify them before assembly. Some parts may be packed in the pad. To prevent serious injury or death 2 Toys (Toys may be different than shown.) from falls and being strangled in the restraint system: Pad Toy Bar • Always use the restraint system. Never rely on the tray to restrain child. • Never use with an active child who may 4 Links be able to climb out of the seat. • Not recommended for children who can sit up by themse
ページ3に含まれる内容の要旨
Assembly IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. Hubs CAUTION This package contains small parts in its unassembled state. Adult assembly is required. Leg Housing Back Base Button Front Curved Base 2 • Place the front curved base on a flat surface so that it curves away from you. • Place
ページ4に含まれる内容の要旨
Assembly CORRECT INCORRECT HUBS FACING OUT HUBS FACING IN FRONT FRONT BASE BASE CURVES CURVES INWARD OUT 3 • Check to be sure you have assembled the leg assemblies to the bases correctly. Please refer to the illustrations above. • If the leg assemblies are assembled incorrectly to the bases, simply pull the legs from the bases. Please re-read and repeat assembly step 2. • Set the frame assembly aside. 4
ページ5に含まれる内容の要旨
Assembly Armrest Holes Oval End Seat Tube Round End Seat Tube Round Seat Bottom 4 • Position the seat bottom so that the back faces you and the 6 Seat Bottom Oval armrest holes are facing up. • Locate the round end seat tube. • Locate the oval end seat tube. Hint: Look at opening in the straight end of the tube. It should be Hint: Look at opening in the straight end of the tube. It should be oval. completely round. • Fit the oval end seat tube into the oval opening in the • Fit the round end sea
ページ6に含まれる内容の要旨
Assembly Seat Back Raised Slots Seat Back Wire Seat Bottom 8 • Fit the seat back to the seat bottom. #8 x 1.9 cm Screw 10 • Fit the seat back wire through the raised slots on the seat back. Rod 9 • Insert the rod into the side opening between the seat back and seat bottom. • Insert a #8 x 1.9 cm screw into the opening in the rod and tighten. 11 • Fit the ends of the seat back wire into the outside holes in the seat tubes. 6
ページ7に含まれる内容の要旨
Assembly Hubs Seat Tubes Assembly Tool 13 • Insert the ends of the seat tubes into the holes in the hubs. Rounded Side • Push the seat tubes in until you hear a “snap” (for each). • Push down on the seat to be sure the seat is secured in both frame hubs. Lock Nut – 2 12 • Attach a lock nut, rounded side facing out, onto one end of a seat back wire. #6 x 3.18 cm Screw – 2 • Tighten the lock nut by using the assembly tool. Turn the tool clockwise to tighten the lock nut. • Repeat this procedure t
ページ8に含まれる内容の要旨
Assembly Elastic Loops Waist Belts 16 Holes • Insert the waist belts through the slots in the pad. • Fit the top of the pad over the seat back edge. Elastic Loops Tabs 15 • Place the pad onto the seat. • Insert the pad elastic loops through the holes in the seat bottom. • From under the seat, fit the elastic loops onto the tabs on the seat back. Tabs 17 • From behind the seat, fit the pad elastic loops to the tabs on the seat back. 8
ページ9に含まれる内容の要旨
Assembly Slot #8 x 1.9 cm Screw – 2 Toy Bar Hubs Crotch Belt Clips Seat Tubes 19 • Fit the toybar hubs to the seat tubes. Hint: The toybar hubs are designed to fit to the seat tubes one way. If the toybar hubs do not fit correctly, turn the toybar around and try again. • Insert a #8 x 1.9 cm screw through the seat tubes and into the toybar hubs. Tighten the screws. Elastic Loops 18 • Fit the crotch belt through the slot in the pad. • Fit the pad side clips around the edge of the seat bottom. • F
ページ10に含まれる内容の要旨
Assembly Tray Tray Links 20 • Fit and “snap” the tray onto the seat armrests. • Insert and “snap” the tray links into the holes in the tray. 21 • Fit the toy links and/or toys on the toy bar/tray! Assembly is now complete. 10
ページ11に含まれる内容の要旨
Battery Installation Hint: We recommend using alkaline batteries for longer battery life. 1,5V x 4 “D” (LR20) Shown Actual Size Battery Safety Information Battery Compartment Batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage: • Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). • Insert batteries as indicated inside the battery compartment. • Remove batt
ページ12に含まれる内容の要旨
Setup and Use IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. Waist Belts WARNING To prevent serious injury or death from falls and being strangled in the restraint system: Crotch Belt • Always use the restraint system. Never rely on the tray to restrain child. 1 • Never use with an active child
ページ13に含まれる内容の要旨
Setup and Use Music Button Power Switch Seat Wire 4 3 Swinging • Make sure your child is properly secured in the seat. • Slide the swing power switch on to any of six speed settings. • Watch the toys move when the seat swings! • Be sure to slide the switch to the off position when the swing is not in use. UPRIGHT SEMI-RECLINE RECLINE Hint: As with most battery-powered swings, a heavier child will reduce the amount of swinging motion on all settings. In most cases, the low Adjust the seat angle t
ページ14に含まれる内容の要旨
Setup and Use Care • The pad is machine washable. Wash it separately in cold water on the gentle cycle. Do not use bleach. Line dry only. •The frame, links, toys and toy bar may be wiped clean using a mild cleaning solution and a damp cloth. Do not use bleach. Toy Bar Do not use harsh or abrasive cleaners. Rinse clean with water to remove residue. Elastic Loops 1 To remove the pad: • Remove the four pad elastic loops from the seat back and bottom tabs. • Remove the top of the pad from the seat.
ページ15に含まれる内容の要旨
Storage Consumer Information GREAT BRITAIN Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB. Toy Bar Helpline: 01628 500302. AUSTRALIA Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia. Consumer Advisory Service 1300 135 312. ASIA Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China. MALAYSIA PRESS BUTTON Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd. (993532-P) Lot 13.5, 13th Floor, M
ページ16に含まれる内容の要旨
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A. ©2004 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. PRINTED IN CHINA H4792pr-0726
